B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO MULTISTAGE CENTRIFUGAL PUMPS - 3ACM-100S



The LEO 3ACm100S is a compact stainless-steel horizontal multistage centrifugal pump designed for clean-water transfer, domestic water supply, pressure boosting, agricultural irrigation and light industrial applications. It features a 3-stage hydraulic design, 0.6 kW / 0.8 HP single-phase 220V motor, 1" × 1" inlet/outlet, AISI 304 stainless-steel shaft and stainless-steel wetted construction. Malaysian supplier specifications list a flow range of approximately 5–78 L/min, head of 33.5–5 m, and maximum suction height of 8 m.

Product Specifications

Specification 3ACm100S
Brand LEO
Model 3ACm100S / 3ACM-100S
Pump Type Horizontal Multistage Centrifugal Pump
Series ACm-S Stainless Steel Series
Number of Stages 3
Motor Power 0.6 kW
Motor Rating 0.8 HP
Motor Type Single Phase
Voltage 220V
Frequency 50 Hz
Flow Range 5–78 L/min
Maximum Flow Approx. 4.68 m³/h
Head Range 33.5–5 m
Maximum Head Approx. 33.5 m
Maximum Suction Height 8 m
Suction Connection 1"
Discharge Connection 1"
Inlet / Outlet 1" × 1"
Pump Construction Stainless Steel
Shaft AISI 304 Stainless Steel
Motor Winding Copper
Insulation Class F
Protection Class IPX4
Motor Protection Built-in Thermal Protection
Pump Orientation Horizontal
Approx. Weight 12 kg
Approx. Dimensions 450 × 250 × 280 mm

The Malaysian product specification confirms 220V, 0.8 HP/0.6 kW, 5–78 L/min, 33.5–5 m head, 8 m maximum suction and 1" × 1" connections.

3-Stage Multistage Design

The "3" in 3ACm100S indicates the pump's three-stage hydraulic arrangement. Multiple impellers operate in series, allowing the pump to generate higher discharge pressure than a comparable single-stage pump.

This makes the 3ACm100S suitable for applications requiring:

  • Higher water pressure
  • Moderate flow
  • Pressure boosting
  • Elevated water transfer
  • Long pipe runs
  • Irrigation systems
  • Domestic water supply

The ACm-S range is designed for clean-water transfer, agriculture, industrial use, pressure boosting and fire-fighting applications.

Hydraulic Performance

The published Malaysian specification gives:

Parameter Performance
Minimum listed flow 5 L/min
Maximum listed flow 78 L/min
Maximum flow conversion 4.68 m³/h
Maximum head 33.5 m
High-flow head Approx. 5 m
Maximum suction 8 m

The 33.5 m maximum head and 78 L/min maximum flow are not achieved simultaneously. The actual operating point depends on the system's total dynamic head, pipe friction, elevation and outlet requirements.

0.6 kW / 0.8 HP Motor

The 3ACm100S uses a 0.6 kW / 0.8 HP single-phase motor operating at 220V.

Key motor features include:

  • 0.6 kW output
  • 0.8 HP rating
  • 220V single phase
  • Copper winding
  • Class F insulation
  • IPX4 protection
  • Built-in thermal protection

The product range is listed with copper winding, thermal protection, Class F insulation and IPX4 motor protection.

Stainless-Steel Construction

The 3ACm100S is the stainless-steel version of the ACm multistage family. It is marketed specifically as a stainless-steel multistage centrifugal pump.

Advantages of the stainless-steel construction include:

  • Improved corrosion resistance
  • Better suitability for clean-water systems
  • Durable wetted components
  • Hygienic water-contact surfaces
  • Suitable appearance for domestic and commercial installations

The shaft is specified as AISI 304 stainless steel.

1" × 1" Connections

The pump uses:

Suction: 1"
Discharge: 1"

The compact connection size makes it suitable for:

  • Domestic water systems
  • Small irrigation systems
  • Water tanks
  • Pressure boosting
  • Garden irrigation
  • Small commercial water systems

For optimum performance, suction piping should be correctly sized, short and free from unnecessary restrictions.

Maximum Suction Height – 8 m

The specified maximum suction height is 8 m.

Actual suction performance depends on:

  • Water temperature
  • Atmospheric pressure
  • Installation elevation
  • Suction pipe length
  • Suction pipe diameter
  • Pipe fittings
  • Water level
  • Air leakage
  • Friction losses

A completely airtight suction line is particularly important for suction-lift installations.

Suitable Fluids

The 3ACm100S is designed primarily for clean water and liquids with physical and chemical properties similar to water.

Suitable fluids/applications include:

  • Clean fresh water
  • Treated water
  • Tank water
  • Well water
  • Irrigation water
  • Domestic water
  • General service water

It should not be used for abrasive slurry, heavily contaminated wastewater or aggressive chemicals unless compatibility has been confirmed.

Applications

The LEO 3ACm100S is suitable for:

  • Domestic water supply
  • Residential water boosting
  • Agricultural irrigation
  • Garden irrigation
  • Small sprinkler systems
  • Water tank transfer
  • Pressure boosting
  • Industrial water supply
  • Clean-water transfer
  • Long-distance water transfer
  • Fire-system applications
  • General water circulation

LEO's ACm-S product range is specifically promoted for clean-water transfer, agriculture, industrial use, pressure boosting and fire-fighting applications.

Domestic Water Supply

The multistage design provides useful pressure for domestic water systems.

Potential applications include:

  • House water supply
  • Water tank transfer
  • Shower pressure boosting
  • Garden taps
  • Residential water distribution
  • Small booster systems

The 3ACm100S is particularly appropriate where a standard single-stage pump does not provide sufficient pressure but a larger industrial pump would be excessive.

Agricultural Irrigation

The pump can be used for small agricultural and garden irrigation systems.

Applications include:

  • Garden sprinklers
  • Nursery irrigation
  • Greenhouse irrigation
  • Small farm irrigation
  • Orchard irrigation
  • Tank-to-field water transfer

At the maximum listed flow of 78 L/min, the theoretical transfer capacity is approximately 4.68 m³/h.

Actual flow will decrease as the required discharge head increases.

Pressure Boosting

The three-stage hydraulic arrangement makes the 3ACm100S suitable for pressure boosting.

Typical uses include:

  • Low-pressure domestic systems
  • Water tank outlet boosting
  • Long pipe runs
  • Garden irrigation
  • Small commercial water systems
  • Elevated water transfer

The correct pump operating point should always be determined from the required flow and total dynamic head.

Industrial Applications

The stainless-steel construction makes the 3ACm100S useful for selected light industrial clean-water applications.

Potential uses include:

  • Process-water transfer
  • Equipment water supply
  • Clean-water circulation
  • Tank filling
  • Small industrial booster systems
  • Utility-water supply

For chemical liquids, material compatibility must be verified before use.

Motor Protection

The motor is specified with:

Insulation: Class F
Protection: IPX4
Thermal protection: Built-in
Winding: Copper

The thermal protector helps prevent motor overheating during abnormal operating conditions.

Appropriate electrical protection and proper earthing should still be provided during installation.

Installation Recommendations

For reliable operation:

  • Install the pump on a firm, level base.
  • Position the pump close to the water source.
  • Keep suction piping short and direct.
  • Ensure suction connections are completely airtight.
  • Use suitable 1" suction piping.
  • Install a foot valve/strainer where required.
  • Avoid excessive bends and restrictions.
  • Support pipework independently.
  • Prime the pump before operation.
  • Ensure adequate water supply.
  • Provide proper electrical earthing.
  • Use appropriate motor protection.
  • Do not operate the pump dry.
  • Keep the pump within its hydraulic operating range.

Maintenance

Recommended maintenance includes:

  • Inspecting for water leakage
  • Checking the mechanical seal
  • Checking suction-line air leakage
  • Cleaning the suction strainer
  • Inspecting impellers and diffusers
  • Checking for abnormal vibration
  • Checking for unusual operating noise
  • Monitoring motor temperature
  • Checking electrical connections
  • Monitoring flow and pressure
  • Inspecting valves and pipework

Dimensions & Weight

The Malaysian supplier specification lists approximately:

Length: 450 mm
Width: 250 mm
Height: 280 mm
Weight: 12 kg.

These dimensions should be treated as product/packaging information rather than a substitute for the manufacturer's installation drawing.

3ACm100S vs 4ACm100S vs 5ACm100S

Specification 3ACm100S 4ACm100S 5ACm100S
Stages 3 4 5
Motor 0.8 HP 1.0 HP 1.25 HP
Voltage 220V 220V 220V
Pump Type Stainless Multistage Stainless Multistage Stainless Multistage
Main Difference Lower power Higher head/power Highest head/power
Typical Use Domestic/irrigation Pressure boosting Higher-pressure applications

The same Malaysian product range lists 3ACM-100S at 0.8 HP, 4ACM-100S at 1.0 HP and 5ACM-100S at 1.25 HP, all in the stainless-steel multistage configuration.

Key Advantages

Three-Stage Design: Provides higher pressure than a basic single-stage pump.

Stainless-Steel Construction: Offers improved corrosion resistance for clean-water applications.

0.8 HP / 0.6 kW Motor: Provides a practical balance between power consumption and hydraulic performance.

Up to 78 L/min Flow: Suitable for domestic, irrigation and light commercial water transfer.

Up to 33.5 m Head: Suitable for moderate pressure-boosting applications.

8 m Maximum Suction: Allows suitable suction-lift installations.

AISI 304 Shaft: Provides good corrosion resistance and mechanical durability.

220V Single Phase: Suitable for standard single-phase electrical installations.

1" × 1" Connections: Compatible with common domestic and irrigation pipework.

Product Summary

The LEO 3ACm100S is a 0.6 kW / 0.8 HP, 220V single-phase, three-stage stainless-steel horizontal multistage centrifugal pump designed for clean-water transfer, domestic water supply, irrigation, pressure boosting and selected industrial applications. It features 1" × 1" inlet/outlet connections, an AISI 304 stainless-steel shaft, stainless-steel construction, copper motor winding, Class F insulation and IPX4 protection.

For Malaysian product specifications, the model is listed at approximately 5–78 L/min flow, 33.5–5 m head and 8 m maximum suction height.



 Inquiry - LEO MULTISTAGE CENTRIFUGAL PUMPS - 3ACM-100S