B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO JET PUMPS - AJM 45



The LEO AJM 45 is a compact self-priming jet water pump designed for clean-water transfer, well-water lifting, garden irrigation and domestic pressure boosting. It is powered by a 0.45 kW / 0.6 HP, 220 V single-phase motor and provides approximately 5–35 L/min flow with a 36–18 m head range. The pump uses 1" × 1" inlet and outlet connections and has a maximum suction capability of approximately 9 m.

Product Overview

The AJM 45 is part of LEO's AJm Jet Pump series, which is designed for applications requiring a compact self-priming pump capable of drawing water from a lower-level source. LEO specifies the AJm series for transferring clean water or liquids with physical and chemical properties similar to water, lifting water from wells, garden sprinkling irrigation, running-water pressure boosting and supporting equipment.

The AJM 45 combines a stainless-steel impeller, AISI 304 stainless-steel shaft, copper motor winding and built-in thermal protection. The standard AJM45 has a cast-iron pump body with anti-rust treatment, while the separate AJM45S version uses a stainless-steel pump body.

Technical Specifications

Specification LEO AJM 45
Brand LEO
Series AJm
Model AJM 45
Pump Type Self-Priming Jet Pump
Motor Power 0.45 kW / 0.6 HP
Voltage 220 V
Phase Single Phase
Frequency 50 Hz
Flow Range 5–35 L/min
Equivalent Flow 0.3–2.1 m³/h
Head Range 36–18 m
Maximum Suction 9 m
Inlet 1"
Outlet 1"
Impeller Stainless Steel
Shaft AISI 304 Stainless Steel
Pump Body Cast Iron with Anti-Rust Treatment
Motor Winding Copper
Thermal Protection Built-In
Insulation Class F
Protection Class IPX4
Maximum Liquid Temperature +40°C
Maximum Ambient Temperature +40°C
Dimensions Approx. 200 × 180 × 400 mm
Weight Approx. 6.2 kg

The above specifications are based primarily on the Malaysian AJM45 listing. Some regional listings use slightly different hydraulic figures, so the nameplate and supplied manufacturer's datasheet should be treated as the final reference for a specific unit.

Pump Performance

The AJM 45 provides a maximum listed flow of approximately 35 L/min and a maximum head of approximately 36 m. As with other centrifugal pumps, the available head decreases as the flow rate increases.

The published hydraulic range is approximately:

  • 5 L/min: up to approximately 36 m head
  • 10 L/min: approximately 32 m head
  • 15 L/min: approximately 29 m head
  • 20 L/min: approximately 26 m head
  • 25 L/min: approximately 23 m head
  • 30 L/min: approximately 20 m head
  • 35 L/min: approximately 18 m head

The exact operating point depends on the total dynamic head, suction conditions, pipe diameter, pipe length, fittings and water-source elevation. LEO's technical documentation identifies the AJm range as a jet pump with hydraulic performance curves for selecting the appropriate duty point.

Self-Priming Jet Pump Design

The self-priming jet-pump configuration allows the AJM 45 to be used for water sources located below the pump, making it suitable for well-water lifting and similar installations.

The maximum suction specified by the Malaysian product listing is approximately 9 m. In practice, the achievable suction height can be lower depending on atmospheric pressure, water temperature, suction-pipe length, pipe diameter, fittings and air leakage.

For best performance, the suction pipe should be correctly sized, properly sealed and installed with as few bends and restrictions as possible.

Stainless-Steel Impeller

The AJM 45 is equipped with a stainless-steel impeller, providing good corrosion resistance and durability in normal clean-water applications. The shaft is manufactured from AISI 304 stainless steel, further improving resistance to corrosion at the rotating shaft assembly.

This configuration makes the pump appropriate for clean-water systems where reliable operation and resistance to rust are important.

Pump Body

The standard AJM45 uses a cast-iron pump body and support with special anti-rust treatment. This should not be confused with the AJM45S, which is the stainless-steel-body version.

For product listing purposes, the standard model should therefore be described as:

AJM45 – stainless-steel impeller + AISI 304 shaft + anti-rust-treated cast-iron pump body

while:

AJM45S – stainless-steel pump body + stainless-steel impeller + AISI 304 shaft

This distinction is useful when customers are comparing the standard AJM45 with the stainless-steel AJM45S.

Motor Specifications

The AJM 45 is fitted with a:

  • 0.45 kW / 0.6 HP motor
  • 220 V single-phase supply
  • 50 Hz frequency
  • Copper winding
  • Built-in thermal protector
  • Class F insulation
  • IPX4 protection

The built-in thermal protector provides protection against excessive motor temperature under abnormal operating conditions.

Connection Size

The pump uses:

Inlet: 1"
Outlet: 1"

The 1" connections make the AJM 45 suitable for common domestic plumbing, small irrigation systems, water tanks and well-water installations.

Proper suction-pipe sizing is particularly important because restrictions on the suction side can reduce performance and increase the risk of cavitation or loss of prime.

Recommended Applications

The LEO AJM 45 is suitable for:

  1. Domestic water supply – For transferring clean water in residential systems.
  2. Well-water lifting – Suitable for drawing water from wells within the applicable suction limit.
  3. Garden irrigation – Suitable for sprinklers, garden hoses and small irrigation systems.
  4. Pressure boosting – Suitable for improving water pressure in domestic and light-duty systems.
  5. Water tank transfer – Can be used to transfer water between storage tanks and other water points.
  6. Small agricultural applications – Suitable for light-duty water transfer and irrigation.
  7. Supporting equipment – Can be incorporated into suitable water-supply and pressure-boosting systems.

LEO specifically identifies well-water lifting, garden irrigation, running-water pressure boosting and supporting equipment as applications for the AJm series.

Suitable Pumping Medium

The AJM 45 is designed for clean water and liquids with physical and chemical properties similar to water.

It is not intended as a solids-handling or wastewater pump. Water containing significant amounts of sand, sludge, fibrous material or abrasive particles should not be pumped unless the application has been specifically approved by the manufacturer.

Operating Conditions

The main operating limits are:

  • Maximum liquid temperature: +40°C
  • Maximum ambient temperature: +40°C
  • Maximum suction: approximately 9 m
  • Insulation: Class F
  • Protection: IPX4

Some Malaysian product documentation specifies a higher water-temperature capability for certain AJM45 listings, but the current standard AJM series specification and Malaysian AJM45 listing indicate +40°C. For catalogue purposes, +40°C is the conservative specification unless the exact unit's datasheet states otherwise.

Main Advantages

The LEO AJM 45 offers:

  • 0.45 kW / 0.6 HP motor
  • 220 V single-phase operation
  • Self-priming jet-pump design
  • Up to approximately 35 L/min flow
  • Up to approximately 36 m head
  • Approximately 9 m maximum suction
  • Stainless-steel impeller
  • AISI 304 stainless-steel shaft
  • Copper motor winding
  • Built-in thermal protection
  • Class F insulation
  • IPX4 motor protection
  • 1" × 1" inlet/outlet
  • Compact construction
  • Suitable for domestic water supply, irrigation and pressure boosting

AJM45 vs AJM45S

Feature AJM45 AJM45S
Motor Power 0.45 kW / 0.6 HP 0.45 kW / 0.6 HP
Voltage 220 V 220 V
Flow 5–35 L/min 5–40 L/min
Head 36–18 m 35–16 m
Max. Suction 9 m 9 m
Impeller Stainless Steel Stainless Steel
Shaft AISI 304 AISI 304
Pump Body Anti-rust-treated cast iron Stainless Steel
Inlet/Outlet 1" × 1" 1" × 1"

The AJM45S is the stainless-steel-body variant and has a somewhat different hydraulic performance range. It should therefore be listed separately rather than treating AJM45 and AJM45S as identical products.

Product Description

LEO AJM 45 Jet Pump 0.45kW / 0.6HP 220V is a compact self-priming jet water pump designed for clean-water transfer, well-water lifting, garden irrigation and pressure boosting. Powered by a 0.45 kW / 0.6 HP single-phase motor, the AJM 45 delivers approximately 5–35 L/min flow with a 36–18 m head range, providing reliable pressure for domestic and light-duty water applications.

The pump features a stainless-steel impeller, AISI 304 stainless-steel shaft and copper motor winding, while the pump body and support feature anti-rust treatment. A built-in thermal protector helps protect the motor against overheating, and Class F insulation with IPX4 protection provides additional electrical and thermal protection.

With 1" × 1" inlet and outlet connections and approximately 9 m maximum suction capability, the LEO AJM 45 is suitable for pumping water from wells, garden irrigation, domestic water transfer, pressure boosting and other clean-water applications.

SEO Product Title

LEO AJM 45 Jet Pump 0.45kW 0.6HP 220V Self-Priming Water Pump

Short Product Description

LEO AJM 45 is a 0.45kW / 0.6HP 220V self-priming jet pump designed for clean-water transfer, well-water lifting, garden irrigation and pressure boosting. It delivers approximately 5–35 L/min flow and 36–18 m head, with 1" × 1" connections, stainless-steel impeller, AISI 304 shaft, copper winding, built-in thermal protection, Class F insulation and IPX4 protection.



 Inquiry - LEO JET PUMPS - AJM 45