The LEO AJM 75 is a self-priming jet water pump designed for clean-water transfer, well-water lifting, garden irrigation and domestic or light commercial pressure boosting. It is powered by a 0.75 kW / 1.0 HP, 220 V single-phase motor and provides a published flow range of approximately 5–65 L/min with a head range of 38–23 m. The pump uses 1" × 1" inlet and outlet connections and has a maximum suction capability of approximately 9 m.
Product Overview
The AJM 75 is part of LEO's AJm self-priming jet pump series. Its jet-pump configuration is intended for applications where water must be drawn from a source below the pump, such as a well, tank or underground water source.
LEO specifies the AJm series for transferring clean water or liquids with similar physical and chemical properties, lifting water from wells, garden irrigation, pressure boosting and related water-supply equipment.
The AJM 75 combines a stainless-steel impeller, AISI 304 stainless-steel shaft, copper motor winding and built-in thermal protection. Malaysian listings identify the standard AJM75 pump body and support as cast iron with anti-rust treatment, while the AJM-S variant uses stainless-steel construction.
Technical Specifications
| Specification | LEO AJM 75 |
|---|---|
| Brand | LEO |
| Series | AJm |
| Model | AJM 75 / AJM75 |
| Pump Type | Self-Priming Jet Pump |
| Motor Power | 0.75 kW / 1.0 HP |
| Voltage | 220–240 V |
| Phase | Single Phase |
| Frequency | 50 Hz |
| Rated Current | Approx. 6.0 A |
| Speed | Approx. 2,900 rpm |
| Flow Range | 5–65 L/min |
| Equivalent Flow | Approx. 0.3–3.9 m³/h |
| Head Range | 38–23 m |
| Maximum Head | Approx. 38–40 m, depending on specification |
| Maximum Suction | Approx. 9 m |
| Inlet | 1" |
| Outlet | 1" |
| Impeller | Stainless Steel |
| Shaft | AISI 304 Stainless Steel |
| Pump Body | Anti-rust-treated cast iron |
| Motor Winding | Copper |
| Thermal Protection | Built-in |
| Insulation Class | F |
| Protection Class | IPX4 |
| Maximum Liquid Temperature | Up to +60°C* |
| Maximum Ambient Temperature | Up to +50°C* |
| Capacitor | 16 μF / 450 V |
| Duty | Continuous |
| Approx. Dimensions | 450 × 210 × 240 mm** |
| Approx. Weight | 6.2 kg*** |
* Operating-temperature figures vary between regional AJM75 documentation; the Malaysian retail specification gives up to +60°C liquid and +50°C ambient.
** Dimensions vary between regional listings.
*** The Malaysian AJM listing gives approximately 6.2 kg, while other AJm75 documentation can specify different package/unit dimensions and weight.
Pump Performance
The AJM 75 is designed for applications requiring a combination of moderate-to-high flow and relatively high pressure.
Its published hydraulic range is approximately:
- Flow: 5–65 L/min
- Equivalent maximum flow: approximately 3.9 m³/h
- Head: 38–23 m
- Maximum head: approximately 38–40 m depending on the published configuration
- Maximum suction: approximately 9 m
The Malaysian LEO listing specifies 5–65 L/min at 38–23 m head, while another Malaysian supplier lists the maximum head as approximately 40 m. These figures represent different published specifications/configurations rather than a flow and head that occur simultaneously.
As with all centrifugal jet pumps, the available head decreases as flow increases. The actual operating point should therefore be selected according to the system's total dynamic head, suction conditions and required water flow.
Self-Priming Jet Pump Design
The self-priming design is one of the main advantages of the AJM 75.
It allows the pump to be used where the water level is below the pump, making it suitable for:
- Well-water lifting
- Underground water sources
- Water tanks
- Garden irrigation
- Domestic water transfer
- Pressure-boosting applications
The maximum suction is listed at approximately 9 m. However, the actual suction height achievable in an installation depends on atmospheric pressure, water temperature, suction-pipe diameter, pipe length, fittings, elevation and the condition of the suction line.
For reliable priming, the suction pipe should be properly sealed against air leakage and fitted with an appropriate foot valve/check valve where required.
Stainless-Steel Impeller
The AJM 75 uses a stainless-steel impeller, providing good corrosion resistance and durability for clean-water pumping applications. The shaft is manufactured from AISI 304 stainless steel, helping resist corrosion at the rotating shaft assembly.
The stainless-steel impeller is particularly useful in domestic and agricultural water systems where resistance to rust is desirable.
Pump Body Construction
The standard AJM75 uses a cast-iron pump body and support with special anti-rust treatment. This differs from the stainless-steel-body AJM-S versions.
Therefore, for accurate product listing:
AJM75:
Cast-iron pump body/support with anti-rust treatment + stainless-steel impeller + AISI 304 shaft.
AJM75S:
Stainless-steel pump body + stainless-steel impeller + AISI 304 shaft.
This distinction is important because the standard AJM75 should not be advertised as a fully stainless-steel pump unless the specific model is confirmed as an AJM75S.
Motor Specifications
The AJM 75 is equipped with a 0.75 kW / 1.0 HP single-phase motor.
Key motor characteristics include:
- 220–240 V
- 50 Hz
- Single phase
- Approximately 2,900 rpm
- Copper winding
- Built-in thermal protector
- Class F insulation
- IPX4 enclosure protection
- Continuous-duty operation
- Approximately 6.0 A current according to one Malaysian specification
- 16 μF / 450 V capacitor according to the same specification
The built-in thermal protector helps protect the motor against overheating during abnormal operating conditions.
Connection Size
The AJM 75 uses:
Inlet: 1"
Outlet: 1"
These 1-inch connections make the pump suitable for common domestic plumbing, garden irrigation systems, water tanks and well-water installations.
For suction applications, it is important to avoid undersized pipework. Excessive suction-line restriction can reduce the pump's effective suction capability and may contribute to cavitation or loss of prime.
Suitable Pumping Medium
The AJM 75 is intended primarily for clean water or liquids with physical and chemical properties similar to water.
It is not a dedicated wastewater or solids-handling pump. Liquids containing substantial quantities of sand, sludge, fibrous material or abrasive particles should not be pumped without confirming suitability.
Operating Temperature
The Malaysian AJM75 product specifications indicate:
- Maximum liquid temperature: +60°C
- Maximum ambient temperature: +50°C
These limits differ from some general AJm-series documentation, so the specification for the actual production version should be checked before using the pump with elevated-temperature liquids. For ordinary domestic water, irrigation and well-water applications, this limitation is normally not an issue.
Recommended Applications
The LEO AJM 75 is suitable for a broad range of clean-water applications.
1. Domestic Water Supply
Suitable for transferring clean water and supplying residential water systems.
2. Well-Water Pumping
The self-priming jet configuration makes the AJM75 suitable for lifting water from wells within its suction limitations.
3. Garden Irrigation
Suitable for garden sprinklers, watering systems and small-scale irrigation.
4. Pressure Boosting
Can be used to improve water pressure in domestic and light-duty water systems.
5. Water Tank Transfer
Suitable for transferring water between storage tanks and other water points.
6. Agricultural Water Transfer
Can be used for small agricultural irrigation and water-transfer applications.
7. General Clean-Water Transfer
Suitable for transferring clean water between sources, tanks and equipment.
LEO's stated applications include clean-water transfer, well-water lifting, garden irrigation and pressure boosting.
Main Advantages
The LEO AJM 75 offers:
- 1.0 HP / 0.75 kW motor for higher performance than the smaller AJM30 and AJM45 models.
- Self-priming jet-pump design for water sources below pump level.
- Up to 65 L/min flow according to the Malaysian specification.
- Up to approximately 38–40 m head depending on the specific published configuration.
- Approximately 9 m maximum suction.
- Stainless-steel impeller for corrosion resistance and durability.
- AISI 304 stainless-steel shaft.
- Copper motor winding.
- Built-in thermal protection.
- Class F insulation.
- IPX4 protection.
- 1" × 1" connections.
- Suitable for domestic supply, well-water lifting, irrigation and pressure boosting.
AJM Series Comparison
| Model | Motor | Voltage | Flow | Head | Max. Suction |
|---|---|---|---|---|---|
| AJM30 | 0.3 kW / 0.4 HP | 220 V | 5–35 L/min | 30–14 m | 9 m |
| AJM45 | 0.45 kW / 0.6 HP | 220 V | 5–35 L/min | 36–18 m | 9 m |
| AJM75 | 0.75 kW / 1.0 HP | 220–240 V | 5–65 L/min | 38–23 m | 9 m |
| AJM110 | 1.1 kW / 1.5 HP | 220 V | 20–100 L/min | 48–22 m | 9 m |
The AJM75 provides a significant increase in flow capacity over the smaller AJM30 and AJM45 while retaining the compact 1-inch connection arrangement.
Product Description
LEO AJM 75 Jet Pump 0.75kW / 1.0HP 220V is a self-priming jet water pump designed for clean-water transfer, well-water lifting, garden irrigation and pressure boosting. Powered by a 0.75 kW / 1.0 HP single-phase motor, the AJM75 provides approximately 5–65 L/min flow with a published 38–23 m head range, making it suitable for domestic and light commercial water-supply applications.
The pump features a stainless-steel impeller, AISI 304 stainless-steel shaft and copper motor winding, while the standard pump body and support receive anti-rust treatment. Built-in thermal protection helps protect the motor against overheating, while Class F insulation and IPX4 protection provide additional electrical and thermal protection.
With 1" × 1" inlet and outlet connections and approximately 9 m maximum suction capability, the LEO AJM75 is suitable for pumping water from wells, transferring water from tanks, garden irrigation, domestic water supply and pressure-boosting systems.
SEO Product Title
LEO AJM75 Jet Pump 0.75kW 1HP 220V Self-Priming Water Pump
Short Product Description
LEO AJM75 is a 0.75kW / 1HP 220V self-priming jet pump designed for clean-water transfer, well-water lifting, garden irrigation and pressure boosting. It delivers approximately 5–65 L/min flow with a 38–23 m head range, features a stainless-steel impeller, AISI 304 shaft, copper winding, built-in thermal protection, Class F insulation and IPX4 protection. Its 1" × 1" connections and approximately 9 m suction capability make it suitable for domestic, agricultural and light commercial water-pumping applications.
Inquiry - LEO JET PUMPS - AJM 75