The LEO AJM 110H is a high-pressure self-priming jet water pump designed for clean-water transfer, well-water lifting, garden irrigation, domestic water supply and pressure-boosting applications. It is powered by a 1.1 kW / 1.5 HP, 220 V single-phase motor and is the high-head (H) version of the AJm110 range.
For the AJM110H specifically, Malaysian product specifications list approximately 10–70 L/min flow, 50–28 m head, 1¼" × 1" connections, and up to 9 m suction lift. LEO's European documentation identifies the AJm110 family at 1.1 kW and distinguishes the H version as the high-pressure/high-head configuration.
Technical Specifications
| Specification | LEO AJM 110H |
|---|---|
| Brand | LEO |
| Series | AJm |
| Model | AJm110H / AJM110H |
| Pump Type | Self-Priming Jet Pump |
| Motor Power | 1.1 kW / 1.5 HP |
| Voltage | 220 V |
| Phase | Single Phase |
| Frequency | 50 Hz |
| Flow Range | 10–70 L/min |
| Equivalent Flow | Approx. 0.6–4.2 m³/h |
| Head Range | 50–28 m |
| Maximum Head | Approx. 50–55 m depending on specification |
| Maximum Suction | Up to 9 m |
| Inlet | 1¼" |
| Outlet | 1" |
| Impeller | Stainless Steel |
| Impeller Material | AISI 304 Stainless Steel |
| Pump Body | Cast Iron with Anti-Rust Treatment |
| Shaft | AISI 304 Stainless Steel |
| Motor Winding | Copper |
| Motor Protection | Built-in Thermal Protector |
| Insulation Class | F |
| Protection Class | IPX4 |
| Maximum Liquid Temperature | +60°C* |
| Maximum Ambient Temperature | +50°C* |
| Duty | Continuous |
| Mechanical Seal | Carbon / Ceramic |
* The AJM110H Malaysian specification lists +60°C liquid and +50°C ambient, while LEO's European documentation for the AJm110 family specifies +40°C for both. For a catalogue, use the specification corresponding to the actual regional unit supplied.
Pump Performance
The AJM110H is designed primarily for higher-pressure applications rather than maximum-volume pumping.
Its Malaysian published performance is:
- Minimum flow: approximately 10 L/min
- Maximum flow: approximately 70 L/min
- Equivalent flow: approximately 0.6–4.2 m³/h
- Maximum head: approximately 50 m
- Operating head range: approximately 50–28 m
- Maximum suction lift: approximately 9 m
LEO's European technical data for the AJm110 family shows the high-head AJm110 configuration reaching approximately 55 m at shut-off, with the head progressively decreasing as flow increases.
Therefore, the 50–55 m maximum-head figures should not be interpreted as being available at the maximum 70 L/min flow rate. The actual operating point must be selected from the pump curve according to the system's required flow and total dynamic head.
High-Head “H” Version
The H designation is significant. LEO identifies the AJm110 family with variants including:
- AJm110H – High head
- AJm110L – Lower-head/high-flow configuration
- AJm110E – Electronic pump-control version
- AJm110LE – Lower-head version with electronic pump control
LEO's technical documentation specifically identifies the H version as the high-flow/high-pressure configuration, while the L version provides a lower head characteristic.
For customers requiring stronger water pressure, longer pipe runs or greater elevation lift, the AJM110H is therefore more appropriate than the lower-head AJM110L, provided the required flow falls within the H model's performance curve.
Self-Priming Jet Pump Design
The AJM110H uses a self-priming jet-pump configuration, allowing it to draw water from a source positioned below the pump.
This makes it suitable for:
- Shallow well pumping
- Underground water sources
- Water tanks
- Domestic water supply
- Garden irrigation
- Pressure boosting
- Water transfer systems
The Malaysian AJM110H specification gives a maximum suction lift of approximately 9 m.
Actual suction performance depends on atmospheric pressure, water temperature, elevation, suction-pipe diameter, pipe length, fittings and air leakage. A practical installation should normally operate below the theoretical maximum suction height.
Stainless-Steel Impeller
The AJM110H is equipped with a stainless-steel impeller, with LEO documentation identifying the impeller as AISI 304 stainless steel.
The stainless-steel impeller provides:
- Good corrosion resistance
- Improved durability
- Better resistance to rust
- Reliable performance in clean-water applications
The pump is intended for clean water or liquids with physical and chemical characteristics similar to water. It is not designed as a solids-handling wastewater pump.
Pump Body Construction
The standard AJM110H uses a cast-iron pump body and support with special anti-rust treatment. LEO documentation identifies the pump body as HT200 cast iron and the impeller as AISI 304 stainless steel.
Therefore, the AJM110H should not be described as a fully stainless-steel pump.
A technically accurate construction description is:
Cast-iron pump body + anti-rust treatment + AISI 304 stainless-steel impeller + AISI 304 stainless-steel shaft.
This is different from LEO's stainless-steel-body variants.
Motor Specifications
The AJM110H is fitted with a 1.1 kW / 1.5 HP single-phase motor.
Key motor features include:
- 220 V
- 50 Hz
- Single phase
- Copper winding
- Built-in thermal protection
- Class F insulation
- IPX4 protection
- Low-noise bearing arrangement
- Continuous-duty capability
The 1.1 kW motor gives the AJM110H considerably more pressure capability than the smaller AJM75 and AJM90 models.
Motor Protection
The motor incorporates a built-in thermal protector for the single-phase configuration. This helps protect the winding against excessive temperature caused by abnormal operating conditions.
The motor is rated:
Insulation: Class F
Protection: IPX4
LEO's European documentation also specifies a maximum ambient temperature of +40°C for the general AJm110 range, while the Malaysian AJM110H listing specifies +50°C.
Pump Connections
The AJM110H uses a larger suction connection than the smaller AJM models:
Inlet: 1¼"
Outlet: 1"
This 1¼" × 1" connection arrangement is an important specification for product listing and installation planning.
The larger suction inlet helps accommodate the higher-capacity pump and can help reduce suction-side losses when appropriately sized piping is used.
Mechanical Seal
LEO's AJm110 documentation identifies a carbon/ceramic mechanical seal.
The mechanical seal provides the rotating shaft seal between the motor/pump assembly and the hydraulic section, helping prevent water leakage along the shaft during operation.
Suitable Pumping Medium
The AJM110H is intended for:
Clean water or liquids with physical and chemical properties similar to water.
It should not normally be used for liquids containing substantial quantities of:
- Sand
- Sludge
- Fibres
- Abrasive solids
- Large suspended particles
For contaminated water or wastewater applications, a dedicated solids-handling pump should be selected.
Recommended Applications
The LEO AJM110H is suitable for:
1. Domestic Water Supply
Provides higher pressure for residential water-supply systems.
2. Well-Water Lifting
Suitable for drawing water from shallow wells within the applicable suction limit.
3. Garden Irrigation
Suitable for sprinkler systems, garden irrigation and water transfer.
4. Pressure Boosting
The high-head configuration is particularly suitable where higher water pressure is required.
5. Water Tank Transfer
Suitable for transferring water between tanks and other storage points.
6. Long Pipe Runs
The higher head capability can be useful where friction losses through pipework are significant.
7. Small Agricultural Applications
Suitable for clean-water irrigation and general agricultural water transfer.
8. Light Commercial Water Systems
Can be used for selected commercial water-supply and pressure-boosting applications.
LEO identifies well-water lifting, garden irrigation and running-water pressure boosting as key applications for the AJm series.
Main Advantages
The LEO AJM110H offers:
- 1.1 kW / 1.5 HP motor for high-pressure water applications.
- High-head H configuration for stronger pressure requirements.
- Approximately 10–70 L/min flow.
- Approximately 50–28 m operating head in the Malaysian specification.
- Up to approximately 50–55 m maximum head, depending on the specific technical specification.
- Up to 9 m suction lift according to Malaysian documentation.
- AISI 304 stainless-steel impeller.
- AISI 304 stainless-steel shaft.
- Anti-rust-treated cast-iron pump body.
- Copper motor winding.
- Built-in thermal protection.
- Class F insulation.
- IPX4 protection.
- 1¼" × 1" inlet/outlet.
- Suitable for domestic, irrigation, well-water and pressure-boosting applications.
AJM Series Comparison
| Model | Motor | Flow Range | Head Range | Max. Suction | Connection |
|---|---|---|---|---|---|
| AJM30 | 0.3 kW / 0.4 HP | 5–35 L/min | 30–14 m | 9 m | 1" × 1" |
| AJM45 | 0.45 kW / 0.6 HP | 5–35 L/min | 36–18 m | 9 m | 1" × 1" |
| AJM75 | 0.75 kW / 1.0 HP | 5–65 L/min | 38–23 m | 9 m | 1" × 1" |
| AJM90 | 0.9 kW / 1.2 HP | 5–65 L/min | 46–30 m | 9 m | 1" × 1" |
| AJM110H | 1.1 kW / 1.5 HP | 10–70 L/min | 50–28 m | 9 m | 1¼" × 1" |
The AJM110H is the next step in the range where higher pressure and larger suction capacity become more important. LEO's technical data confirms that the AJm110H belongs to the 1.1 kW high-head configuration.
Dimensions & Weight
LEO documentation lists the AJm110H at approximately:
- Length: 512 mm
- Width: 206 mm
- Height: 236 mm
- Gross/package weight: approximately 24.5 kg
Packaging information gives approximately 572 × 225 × 259 mm.
These figures are useful for catalogue and logistics purposes, although actual packaged dimensions can vary by market.
Product Description
LEO AJM110H Jet Pump 1.1kW / 1.5HP 220V is a high-pressure self-priming jet water pump designed for clean-water transfer, well-water lifting, garden irrigation, domestic water supply and pressure boosting. Powered by a 1.1 kW / 1.5 HP single-phase motor, the AJM110H provides approximately 10–70 L/min flow with a 50–28 m head range, making it suitable for applications requiring higher water pressure.
The pump features an AISI 304 stainless-steel impeller and shaft, anti-rust-treated cast-iron pump body and support, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. Its self-priming jet design provides approximately 9 m maximum suction capability, subject to actual installation conditions.
With a 1¼" inlet and 1" outlet, the LEO AJM110H is well suited to well-water pumping, domestic water supply, garden irrigation, water tank transfer, pressure boosting and other clean-water applications where higher head performance is required.
SEO Product Title
LEO AJM110H Jet Pump 1.1kW 1.5HP 220V High Head Self-Priming Water Pump
Short Product Description
LEO AJM110H is a 1.1kW / 1.5HP 220V high-head self-priming jet pump designed for clean-water transfer, well-water lifting, irrigation and pressure boosting. It delivers approximately 10–70 L/min flow with a 50–28 m head range, featuring an AISI 304 stainless-steel impeller and shaft, anti-rust-treated cast-iron pump body, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. With a 1¼" × 1" inlet/outlet and up to approximately 9 m suction lift, it is suitable for domestic, agricultural and light commercial water-pumping applications.
Inquiry - LEO JET PUMPS - AJM 110H