B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO JET PUMPS - AJM 150H



The LEO AJM150H is a high-head, self-priming jet water pump designed for clean-water transfer, well-water lifting, garden irrigation, domestic water supply and pressure boosting. It is equipped with a 1.5 kW / 2 HP single-phase motor and is specifically configured for applications requiring higher delivery pressure.

Malaysian LEO pump catalogues list the AJM150H at 220 V, 10–60 L/min flow, 66–41 m head, maximum 9 m suction and 1¼" × 1" inlet/outlet.

Technical Specifications

Specification LEO AJM 150H
Brand LEO
Series AJm
Model AJM150H
Pump Type Self-Priming Jet Pump
Motor Power 1.5 kW / 2 HP
Voltage 220 V
Phase Single Phase
Frequency 50 Hz
Flow Range 10–60 L/min
Equivalent Flow Approx. 0.6–3.6 m³/h
Head Range 66–41 m
Maximum Head Approx. 66 m
Maximum Suction 9 m
Inlet 1¼"
Outlet 1"
Impeller Stainless Steel
Impeller Material Stainless Steel / AISI 304
Shaft AISI 304 Stainless Steel
Pump Body Cast Iron
Pump Support Cast Iron
Pump Body Treatment Special Anti-Rust Treatment
Motor Winding Copper
Bearing C&U
Motor Protection Built-In Thermal Protector
Insulation Class F
Protection Class IPX4
Maximum Liquid Temperature +40°C
Maximum Ambient Temperature +40°C
Mechanical Seal Carbon / Ceramic
Duty Continuous

The above figures are based on Malaysian AJM150H catalog and product specifications.

Pump Performance

The AJM150H is designed primarily for high-head water pumping.

Published hydraulic performance is:

  • Flow: 10–60 L/min
  • Maximum flow: approximately 60 L/min
  • Equivalent flow: approximately 3.6 m³/h
  • Head: 66–41 m
  • Maximum head: approximately 66 m
  • Maximum suction: 9 m

The 66 m figure represents the maximum available head at the low-flow end of the pump curve. It does not mean the pump can deliver 60 L/min at 66 m head. As flow increases, the available head decreases.

This high-head characteristic makes the AJM150H suitable for systems where elevation, pipe friction or pressure requirements are greater than those normally handled by smaller AJM models.

High-Head H Configuration

The “H” designation identifies the high-head configuration of the AJM150 series.

The AJM150H is intended for applications where pressure/head is more important than maximum flow volume. This makes it suitable for:

  • Multi-storey domestic water supply
  • Long-distance water transfer
  • Well-water lifting
  • Pressure boosting
  • Garden irrigation
  • Sprinkler systems
  • Water tank transfer
  • Small agricultural water systems

The high-head design provides substantially more pressure capability than the smaller AJM75 and AJM90 models.

Self-Priming Jet Pump Design

The AJM150H uses a self-priming jet-pump configuration, allowing it to draw water from a source positioned below the pump.

The specified maximum suction is approximately 9 m.

Typical applications include:

  • Shallow wells
  • Underground water tanks
  • Ground-level storage tanks
  • Domestic water sources
  • Irrigation reservoirs

Actual suction performance depends on installation conditions. Suction-pipe diameter, pipe length, elevation, water temperature, fittings and air leakage can all affect the achievable suction lift.

For reliable operation, the suction line should be properly sealed and appropriately sized. A foot valve or suitable check valve may also be required depending on the installation.

Stainless-Steel Impeller

The AJM150H features a stainless-steel impeller, providing good corrosion resistance and durability for clean-water applications. Malaysian product information specifically identifies the stainless-steel impeller as one of the pump's construction features.

The impeller is suitable for:

  • Domestic clean-water pumping
  • Well-water pumping
  • Garden irrigation
  • Water tank transfer
  • Pressure boosting

The pump is not intended to handle substantial quantities of abrasive solids, sludge or fibrous wastewater.

AISI 304 Stainless-Steel Shaft

The AJM150H uses an AISI 304 stainless-steel shaft.

A stainless-steel shaft provides improved corrosion resistance and durability at the rotating assembly. It is particularly useful in water-pumping equipment where the shaft is exposed to moisture during normal operation.

Pump Body Construction

The standard AJM150H uses a cast-iron pump body and support with special anti-rust treatment.

The construction can therefore be summarized as:

Cast-iron pump body + anti-rust treatment + stainless-steel impeller + AISI 304 stainless-steel shaft.

The AJM150H should not be advertised as a fully stainless-steel pump unless the actual unit is a stainless-steel-body variant.

Motor Specifications

The AJM150H is equipped with a 1.5 kW / 2 HP single-phase motor.

Key motor features include:

  • 1.5 kW rated power
  • 2 HP equivalent
  • 220 V supply
  • 50 Hz
  • Single phase
  • Copper winding
  • C&U bearing
  • Built-in thermal protector
  • Class F insulation
  • IPX4 protection
  • Continuous-duty design

The 1.5 kW motor provides the power necessary for the pump's high-head hydraulic performance.

Built-In Thermal Protection

The single-phase motor incorporates a built-in thermal protector. This helps protect the motor winding from excessive temperature during abnormal operating conditions such as overload or inadequate cooling.

The motor is specified with:

Insulation Class: F
Protection Class: IPX4

Class F insulation provides suitable thermal resistance for the motor winding, while IPX4 provides protection against water splashing from different directions.

Pump Connections

The AJM150H uses:

Inlet: 1¼"
Outlet: 1"

The 1¼" suction inlet is particularly important for maintaining suitable suction conditions on a pump with this capacity.

A correctly sized suction pipe can reduce friction losses and improve the pump's ability to maintain prime.

Mechanical Seal

The AJM series uses a carbon/ceramic mechanical seal in the pump assembly.

The mechanical seal prevents water from escaping along the rotating shaft between the hydraulic section and motor assembly.

Suitable Pumping Medium

The AJM150H is designed for clean water and liquids with physical and chemical properties similar to water.

It is suitable for normal clean-water applications but is not a dedicated wastewater or solids-handling pump.

Avoid using it for liquids containing high levels of:

  • Sand
  • Sludge
  • Fibres
  • Abrasive solids
  • Large suspended particles

unless pump suitability has been specifically confirmed.

Operating Temperature

The AJM150H product specification lists:

  • Maximum liquid temperature: +40°C
  • Maximum ambient temperature: +40°C

This makes the pump appropriate for standard cold-water and normal-temperature water applications.

Recommended Applications

1. Domestic Water Supply

The high-head performance makes the AJM150H suitable for domestic water systems requiring stronger pressure, particularly where there are elevation differences or longer pipe runs.

2. Well-Water Lifting

The self-priming design and approximately 9 m suction capability make it suitable for shallow-well applications within the pump's operating limits.

3. Garden Irrigation

The AJM150H can supply sprinklers, hoses and irrigation systems requiring higher pressure.

4. Pressure Boosting

The high-head characteristic makes it suitable for boosting water pressure in residential and light commercial systems.

5. Water Tank Transfer

Suitable for transferring water between storage tanks, reservoirs and distribution systems.

6. Agricultural Irrigation

Suitable for small-scale clean-water irrigation systems where higher head is required.

7. Long Pipe Runs

The higher available head can help overcome friction losses in longer pipe networks.

8. Multi-Storey Water Supply

The AJM150H can be considered for applications where water must be lifted to higher elevations, subject to the actual flow/head requirement.

Main Advantages

The LEO AJM150H provides:

  1. 1.5 kW / 2 HP motor
  2. High-head pump configuration
  3. 10–60 L/min flow range
  4. 66–41 m head range
  5. Up to approximately 66 m maximum head
  6. Approximately 9 m maximum suction
  7. Stainless-steel impeller
  8. AISI 304 stainless-steel shaft
  9. Anti-rust-treated cast-iron pump body
  10. Copper motor winding
  11. C&U bearing
  12. Built-in thermal protector
  13. Class F insulation
  14. IPX4 protection
  15. 1¼" × 1" inlet/outlet
  16. Carbon/ceramic mechanical seal
  17. Suitable for domestic, irrigation, well-water and pressure-boosting applications.

AJM High-Head Series Comparison

Model Motor Flow Head Max. Suction Connection
AJM90 0.9 kW / 1.2 HP 5–65 L/min 46–30 m 9 m 1" × 1"
AJM110H 1.1 kW / 1.5 HP 10–70 L/min 50–28 m 9 m 1¼" × 1"
AJM150H 1.5 kW / 2 HP 10–60 L/min 66–41 m 9 m 1¼" × 1"

The AJM150H is the higher-powered, substantially higher-head option in this sequence. Its principal advantage over the AJM110H is higher pressure/head capability, reaching approximately 66 m maximum head in the Malaysian specification.

Dimensions & Weight

Published Malaysian listings show some variation in physical dimensions and weight:

  • One listing: approximately 572 × 225 × 259 mm, 25.4 kg including listed product/package information.
  • Another supplier lists approximately 620 × 250 × 280 mm and 22 kg.

For website catalogue purposes, the manufacturer/actual packaging specification should take precedence because supplier-listed dimensions can represent different packaging configurations.

Product Description

LEO AJM150H Jet Pump 1.5kW / 2HP 220V is a high-head self-priming water pump designed for clean-water transfer, well-water lifting, garden irrigation, domestic water supply and pressure boosting. Powered by a 1.5 kW / 2 HP single-phase motor, the AJM150H delivers approximately 10–60 L/min flow with a 66–41 m head range, making it suitable for applications requiring high water pressure and substantial elevation lift.

The pump features a stainless-steel impeller and AISI 304 stainless-steel shaft, together with a specially anti-rust-treated cast-iron pump body and support. The motor uses copper winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection for reliable operation in suitable water-pumping environments.

With a 1¼" inlet and 1" outlet and approximately 9 m maximum suction capability, the LEO AJM150H is suitable for well-water pumping, domestic water supply, garden and agricultural irrigation, water tank transfer, pressure boosting and higher-elevation water delivery systems.

SEO Product Title

LEO AJM150H Jet Pump 1.5kW 2HP 220V High Head Self-Priming Water Pump

Short Product Description

LEO AJM150H is a 1.5kW / 2HP 220V high-head self-priming jet pump designed for clean-water transfer, well-water lifting, irrigation and pressure boosting. It provides approximately 10–60 L/min flow and 66–41 m head, with a stainless-steel impeller, AISI 304 shaft, anti-rust-treated cast-iron pump body, copper winding, built-in thermal protection, Class F insulation and IPX4 protection. Its 1¼" × 1" connections and approximately 9 m suction capability make it suitable for domestic, agricultural and light commercial high-pressure water applications.



 Inquiry - LEO JET PUMPS - AJM 150H