B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO JET PUMPS - AJM 150L



The LEO AJM150L is a 1.5 kW / 2 HP single-phase self-priming jet pump designed for clean-water transfer, well-water lifting, garden irrigation, domestic water supply and pressure boosting. The “L” version is the high-flow configuration, providing substantially greater flow than the high-head AJM150H, while operating at a lower head range.

Current Malaysian product listings specify 40–140 L/min flow, 44–24 m head, 9 m maximum suction and 1¼" × 1" connections.

Technical Specifications

Specification LEO AJM150L
Brand LEO
Series AJm
Model AJM150L
Pump Type Self-Priming Jet Pump
Motor Power 1.5 kW / 2 HP
Voltage 220 V
Phase Single Phase
Frequency 50 Hz
Flow Range 40–140 L/min
Equivalent Flow Approx. 2.4–8.4 m³/h
Head Range 44–24 m
Maximum Head Approx. 44 m
Maximum Suction 9 m
Inlet 1¼"
Outlet 1"
Impeller Stainless Steel
Shaft AISI 304 Stainless Steel
Pump Body Cast Iron
Pump Support Cast Iron
Pump Body Treatment Special Anti-Rust Treatment
Motor Winding Copper
Bearing C&U
Thermal Protection Built-In, Single Phase
Insulation Class F
Protection Class IPX4
Maximum Liquid Temperature +40°C
Maximum Ambient Temperature +40°C
Mechanical Seal Carbon / Ceramic
Approx. Weight 25.4–29 kg
Approx. Dimensions 572 × 225 × 259 mm to 600 × 240 × 280 mm

Published Malaysian specifications show minor differences in physical dimensions and weight between suppliers, while the core hydraulic specifications are consistent.

Pump Performance

The AJM150L is designed for higher-volume water delivery.

Published performance:

  • Flow: 40–140 L/min
  • Maximum flow: approximately 140 L/min
  • Equivalent maximum flow: approximately 8.4 m³/h
  • Head: 44–24 m
  • Maximum head: approximately 44 m
  • Maximum suction: 9 m

The 44 m maximum head and 140 L/min maximum flow are not simultaneous operating points. Like other centrifugal pumps, the AJM150L follows a pump curve in which available head decreases as flow increases.

This makes the AJM150L particularly suitable when the application requires more water volume at moderate pressure, rather than the higher pressure characteristic of the AJM150H.

AJM150L High-Flow Configuration

The “L” designation differentiates this model from the AJM150H.

The two 2 HP models serve different hydraulic requirements:

Feature AJM150H AJM150L
Motor 1.5 kW / 2 HP 1.5 kW / 2 HP
Flow 10–60 L/min 40–140 L/min
Head 66–41 m 44–24 m
Max. Suction 9 m 9 m
Inlet 1¼" 1¼"
Outlet 1" 1"
Primary Characteristic High Head High Flow

The AJM150H is therefore better suited to high-pressure/high-head applications, while the AJM150L is better suited to higher-volume water transfer and irrigation applications. Malaysian listings confirm these distinct performance ranges.

Self-Priming Jet Pump Design

The AJM150L uses a self-priming jet-pump design, allowing the pump to lift water from a source located below the pump.

The published maximum suction is approximately 9 m.

Typical applications include:

  • Shallow wells
  • Water storage tanks
  • Underground water sources
  • Garden irrigation
  • Domestic water supply
  • Pressure boosting
  • Agricultural water transfer

Actual suction performance depends on the installation. Pipe diameter, suction-pipe length, elevation, fittings, water temperature and air leakage can all affect the practical suction height.

For reliable operation, the suction pipe should be properly sealed and appropriately sized. A foot valve or check valve may be required to maintain prime depending on the installation.

Stainless-Steel Impeller

The AJM150L uses a stainless-steel impeller, providing good corrosion resistance and durability for clean-water applications.

The stainless-steel impeller is suitable for:

  • Domestic water supply
  • Well-water pumping
  • Garden irrigation
  • Agricultural irrigation
  • Water tank transfer
  • Pressure boosting

The pump is not intended for substantial quantities of sand, sludge, fibrous solids or abrasive wastewater.

AISI 304 Stainless-Steel Shaft

The pump is equipped with an AISI 304 stainless-steel shaft.

The stainless-steel shaft provides improved corrosion resistance and durability in the rotating assembly and is well suited to normal clean-water pumping conditions.

Pump Body Construction

The standard AJM150L uses a cast-iron pump body and support with special anti-rust treatment.

The construction can therefore be accurately described as:

Cast-iron pump body + anti-rust treatment + stainless-steel impeller + AISI 304 stainless-steel shaft.

The AJM150L should not be marketed as a fully stainless-steel pump unless the specific unit is confirmed as a stainless-steel-body variant.

Motor Specifications

The AJM150L is powered by a 1.5 kW / 2 HP single-phase motor.

Key motor characteristics include:

  • 1.5 kW rated power
  • 2 HP
  • 220 V
  • 50 Hz
  • Single phase
  • Copper winding
  • C&U bearing
  • Built-in thermal protection
  • Class F insulation
  • IPX4 protection
  • Continuous-duty operation

The 1.5 kW motor provides sufficient power for the AJM150L's high-flow hydraulic configuration.

Motor Protection

The AJM150L uses a built-in thermal protector for the single-phase motor. This helps protect the motor winding from excessive temperature caused by abnormal operating conditions.

The electrical protection specifications are:

Insulation Class: F
Protection Class: IPX4

IPX4 protection provides resistance to water splashing from different directions, while Class F insulation provides suitable thermal protection for the motor winding.

Pump Connections

The AJM150L uses:

Inlet: 1¼"
Outlet: 1"

This 1¼" suction × 1" discharge configuration should be taken into consideration when designing the pipework.

Because this is the high-flow version, an adequately sized suction line is particularly important. Undersized suction piping can increase friction losses and reduce pump performance.

Mechanical Seal

The AJM series uses a carbon/ceramic mechanical seal for sealing around the rotating shaft. This helps prevent water leakage from the hydraulic section into the motor assembly.

Suitable Pumping Medium

The AJM150L is intended for clean water and liquids with physical and chemical properties similar to water.

Suitable liquids should generally be free from significant quantities of:

  • Sand
  • Sludge
  • Fibres
  • Abrasive solids
  • Large suspended particles

For wastewater or solids-containing liquids, a dedicated wastewater or solids-handling pump should be selected.

Operating Temperature

Published Malaysian specifications give:

  • Maximum liquid temperature: +40°C
  • Maximum ambient temperature: +40°C

The AJM150L is therefore intended primarily for normal-temperature clean-water applications.

Recommended Applications

1. Garden Irrigation

The high-flow configuration makes the AJM150L suitable for garden sprinklers, irrigation lines and larger watering systems.

2. Agricultural Irrigation

With up to approximately 140 L/min published flow, it can be used for selected small-scale agricultural irrigation and water-transfer duties.

3. Well-Water Pumping

The self-priming configuration allows water to be lifted from suitable shallow wells within the approximately 9 m suction limit.

4. Domestic Water Transfer

Suitable for transferring clean water between tanks and supplying residential water systems.

5. Water Tank Filling

The relatively high flow makes the AJM150L useful where tanks need to be filled or transferred between storage points efficiently.

6. Pressure Boosting

Although it is the high-flow rather than high-head configuration, its 44 m maximum head makes it suitable for selected pressure-boosting applications.

7. Water Transfer

Suitable for moving relatively large volumes of clean water over moderate distances and elevations.

8. Light Agricultural and Commercial Applications

Can be used in suitable clean-water systems where the required duty point falls within the AJM150L pump curve.

LEO's AJM series is specified for clean-water transfer, well-water lifting, garden sprinkler irrigation, pressure boosting and supporting equipment.

Main Advantages

The LEO AJM150L offers:

  1. 1.5 kW / 2 HP motor
  2. High-flow pump configuration
  3. 40–140 L/min flow range
  4. 44–24 m head range
  5. Approximately 44 m maximum head
  6. Approximately 9 m maximum suction
  7. Stainless-steel impeller
  8. AISI 304 stainless-steel shaft
  9. Anti-rust-treated cast-iron pump body
  10. Copper motor winding
  11. C&U bearing
  12. Built-in thermal protection
  13. Class F insulation
  14. IPX4 protection
  15. 1¼" × 1" inlet/outlet
  16. Carbon/ceramic mechanical seal
  17. Suitable for irrigation, well-water pumping, water transfer and domestic applications.

AJM Series Comparison

Model Motor Flow Range Head Range Max. Suction Connection
AJM75 0.75 kW / 1 HP 5–65 L/min 38–23 m 9 m 1" × 1"
AJM90 0.9 kW / 1.2 HP 5–65 L/min 46–30 m 9 m 1" × 1"
AJM110H 1.1 kW / 1.5 HP 10–70 L/min 50–28 m 9 m 1¼" × 1"
AJM150H 1.5 kW / 2 HP 10–60 L/min 66–41 m 9 m 1¼" × 1"
AJM150L 1.5 kW / 2 HP 40–140 L/min 44–24 m 9 m 1¼" × 1"

The AJM150L is the high-flow 2 HP model, while the AJM150H is optimized for substantially higher head.

AJM150L vs AJM150H

The most important distinction is the hydraulic duty.

AJM150H:
Designed for higher head and pressure, with approximately 10–60 L/min flow and 66–41 m head.

AJM150L:
Designed for higher flow, with approximately 40–140 L/min flow and 44–24 m head.

Therefore:

  • Choose AJM150H when higher pressure/elevation is the priority.
  • Choose AJM150L when higher water volume at moderate pressure is the priority.

Dimensions & Weight

Current Malaysian supplier specifications list:

  • JSG Machinery: approximately 600 × 240 × 280 mm, 29 kg.
  • HardwareMart: approximately 572 × 225 × 259 mm, 25.4 kg.

These differences may reflect packaging or supplier measurement methods. For your website catalogue, the actual manufacturer's packaging specification should be used if available.

Product Description

LEO AJM150L Jet Pump 1.5kW / 2HP 220V is a high-flow self-priming water pump designed for clean-water transfer, well-water lifting, garden irrigation, agricultural water transfer, domestic water supply and pressure boosting. Powered by a 1.5 kW / 2 HP single-phase motor, the AJM150L delivers approximately 40–140 L/min flow with a 44–24 m head range, making it particularly suitable for applications requiring higher water volume at moderate pressure.

The pump features a stainless-steel impeller and AISI 304 stainless-steel shaft, together with a specially anti-rust-treated cast-iron pump body and support. The motor uses copper winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection for reliable operation under suitable conditions.

With a 1¼" inlet and 1" outlet and approximately 9 m maximum suction capability, the LEO AJM150L is suitable for well-water pumping, garden and agricultural irrigation, water tank transfer, domestic water supply and higher-volume clean-water transfer applications.

SEO Product Title

LEO AJM150L Jet Pump 1.5kW 2HP 220V High Flow Self-Priming Water Pump

Short Product Description

LEO AJM150L is a 1.5kW / 2HP 220V high-flow self-priming jet pump designed for clean-water transfer, well-water pumping, irrigation and domestic water supply. It provides approximately 40–140 L/min flow and 44–24 m head, featuring a stainless-steel impeller, AISI 304 shaft, anti-rust-treated cast-iron pump body, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. Its 1¼" × 1" connections and approximately 9 m suction capability make it suitable for high-volume domestic, agricultural and water-transfer applications.



 Inquiry - LEO JET PUMPS - AJM 150L