The LEO AJDm75/2H is a deep-well jet pump designed for lifting clean water from deeper wells where a standard shallow-well jet pump may not provide sufficient suction capability. It is suitable for deep-well water supply, garden irrigation, pressure boosting and general clean-water transfer.
The pump uses a 0.75 kW / 1 HP single-phase motor and a deep-well jet/ejector arrangement. Published technical data for the AJDm75/2H gives a maximum suction capability of approximately 40 m, making it substantially different from the standard AJM75S shallow-well jet pump.
Technical Specifications
| Specification | LEO AJDm75/2H |
|---|---|
| Brand | LEO |
| Series | AJDm |
| Model | AJDm75/2H |
| Pump Type | Deep-Well Jet Pump |
| Motor Power | 0.75 kW / 1 HP |
| Voltage | 220 V |
| Phase | Single Phase |
| Frequency | 50 Hz |
| Maximum Suction / Lifting Depth | Approx. 40 m |
| Head at 0 L/min | Approx. 47 m |
| Flow at 2 L/min | Approx. 43 m head |
| Flow at 4 L/min | Approx. 40 m head |
| Flow at 6 L/min | Approx. 37 m head |
| Flow at 8 L/min | Approx. 34 m head |
| Flow at 10 L/min | Approx. 31 m head |
| Flow at 12 L/min | Approx. 29 m head |
| Flow at 14 L/min | Approx. 27 m head |
| Flow at 16 L/min | Approx. 25 m head |
| Flow at 18 L/min | Approx. 23 m head |
| Flow at 20 L/min | Approx. 21 m head |
| Flow at 22 L/min | Approx. 19 m head |
| Flow at 24 L/min | Approx. 17 m head |
| Maximum Liquid Temperature | +40°C |
| Maximum Ambient Temperature | +40°C |
| Impeller | Stainless Steel |
| Shaft | AISI 304 Stainless Steel |
| Pump Body | Cast Iron, Special Anti-Rust Treatment |
| Pump Support | Cast Iron, Special Anti-Rust Treatment |
| Motor Winding | Copper |
| Bearing | C&U |
| Thermal Protection | Built-In |
| Insulation Class | F |
| Protection Class | IPX4 |
| Duty | Continuous |
The available technical data specifically identifies the AJDm75/2H as a 0.75 kW / 1 HP deep-well jet pump and provides its head-versus-flow performance points.
Deep-Well Jet Pump Design
The main advantage of the AJDm75/2H is its deep-well configuration.
Unlike a conventional shallow-well jet pump, the AJDm system is designed to work with a deep-well ejector arrangement, allowing water to be lifted from considerably greater depths. LEO classifies the AJDm specifically as a “Jet Pump for Deep Wells.”
This makes the pump suitable for:
- Deep wells
- Bore wells with suitable ejector installation
- Underground water sources
- Farm water supply
- Garden irrigation
- Domestic water supply
- Pressure boosting
- Clean-water transfer
The manufacturer specifically lists well-water lifting, garden sprinkler irrigation and running-water pressure boosting among the intended applications.
Maximum Suction Capability
One of the most important specifications of the AJDm75/2H is its approximately 40 m maximum suction/lifting capability when installed with the appropriate deep-well ejector system.
This should not be confused with the approximately 8–9 m suction capability of a conventional surface jet pump.
The actual achievable depth depends on:
- Well depth
- Water-table level
- Ejector installation depth
- Suction and delivery pipe size
- Pipe friction losses
- Number of pipe bends
- Foot-valve condition
- Water temperature
- System leakage
- Required flow rate
Therefore, the 40 m figure should be treated as the maximum specified suction/lifting capability rather than a guaranteed operating depth at maximum flow.
Performance Curve
The published AJDm75/2H data gives the following approximate relationship between flow and head:
| Flow | Head |
|---|---|
| 0 L/min | 47 m |
| 2 L/min | 43 m |
| 4 L/min | 40 m |
| 6 L/min | 37 m |
| 8 L/min | 34 m |
| 10 L/min | 31 m |
| 12 L/min | 29 m |
| 14 L/min | 27 m |
| 16 L/min | 25 m |
| 18 L/min | 23 m |
| 20 L/min | 21 m |
| 22 L/min | 19 m |
| 24 L/min | 17 m |
These figures show that the pump's available discharge head decreases as the water flow increases.
For example, at approximately 10 L/min, the published data indicates about 31 m head, while at approximately 20 L/min, the available head is about 21 m.
Stainless-Steel Impeller
The AJDm75/2H uses a stainless-steel impeller, providing good corrosion resistance and durability for clean-water pumping applications.
The stainless-steel impeller is suitable for:
- Well water
- Domestic water
- Garden irrigation
- Agricultural water supply
- Water tank transfer
- General clean-water applications
The pump is not intended for heavy abrasive liquids, sewage, sludge or water containing significant quantities of solids.
AISI 304 Stainless-Steel Shaft
The pump uses an AISI 304 stainless-steel shaft, providing corrosion resistance and mechanical strength in the rotating assembly.
This complements the stainless-steel impeller and provides a durable hydraulic assembly for normal clean-water applications.
Anti-Rust Pump Body
The AJDm75/2H is constructed with a cast-iron pump body and support receiving special anti-rust treatment.
This is an important distinction for product specifications: the AJDm75/2H should not be described as a completely stainless-steel pump.
Its construction is:
- Pump body: Cast iron with special anti-rust treatment
- Pump support: Cast iron with special anti-rust treatment
- Impeller: Stainless steel
- Shaft: AISI 304 stainless steel
This combination provides a practical balance between mechanical strength, corrosion resistance and cost.
Motor Specifications
The AJDm75/2H is equipped with a 0.75 kW / 1 HP single-phase motor.
Motor features include:
- 0.75 kW output
- 1 HP rating
- Single-phase operation
- Copper winding
- C&U bearing
- Built-in thermal protector
- Class F insulation
- IPX4 protection
- Maximum ambient temperature +40°C
Copper Motor Winding
The motor uses copper winding, which provides good electrical conductivity and reliable thermal characteristics for continuous water-pumping operation.
Copper winding also contributes to the motor's durability when the pump is operated within its specified electrical and hydraulic operating conditions.
Built-In Thermal Protection
The single-phase motor incorporates a built-in thermal protector. This helps protect the motor winding against overheating caused by abnormal operating conditions such as excessive load or inadequate cooling.
Proper external electrical protection should still be provided according to the installation requirements.
Insulation & Protection
The motor is specified with:
Insulation Class: F
Protection Class: IPX4
Maximum Ambient Temperature: +40°C.
The IPX4 rating provides protection against water splashing from different directions, making the motor suitable for normal protected pump-room and outdoor installations when appropriately installed.
Pumping Medium
The AJDm75/2H is designed for clean water or liquids with physical and chemical properties similar to water. LEO specifies the AJDm series for clean-water transfer and well-water lifting.
Recommended fluids include:
- Clean well water
- Fresh water
- Stored water
- Irrigation water
- Domestic water
It should not be selected for:
- Sewage
- Sludge
- Mud
- Highly abrasive water
- Fibrous liquids
- Large suspended solids
If the well contains sand or sediment, appropriate well development and filtration should be considered before operating the pump.
Maximum Liquid Temperature
The published AJDm75/2H specification gives a maximum liquid temperature of +40°C and maximum ambient temperature of +40°C.
For normal well-water and garden-irrigation applications, this is generally more than adequate.
Recommended Applications
Deep-Well Water Supply
The AJDm75/2H is specifically designed for applications where water must be lifted from a deeper well using a suitable ejector system.
Garden Irrigation
It can supply water to sprinklers, hoses and garden irrigation systems when the required flow and pressure are within the pump's performance curve.
Farm Irrigation
The pump is suitable for small-scale agricultural irrigation using clean groundwater.
Domestic Water Supply
It can be used to supply clean water from a suitable well to a residential water system.
Pressure Boosting
The pump can be used to increase water pressure in suitable clean-water systems.
Water Tank Filling
It can transfer clean water from a well or other source into an elevated or storage tank.
Advantages of LEO AJDm75/2H
The main advantages include:
- Designed specifically for deep-well applications
- Approximately 40 m maximum suction/lifting capability
- 0.75 kW / 1 HP motor
- Stainless-steel impeller
- AISI 304 stainless-steel shaft
- Anti-rust-treated cast-iron pump body
- Anti-rust-treated pump support
- Copper motor winding
- C&U bearing
- Built-in thermal protection
- Class F insulation
- IPX4 motor protection
- Suitable for garden irrigation
- Suitable for well-water lifting
- Suitable for domestic water supply
- Suitable for pressure boosting
- Suitable for clean-water transfer.
AJDM75/2H vs AJM75S
These two models should not be treated as the same pump.
| Feature | AJM75S | AJDm75/2H |
|---|---|---|
| Pump Type | Shallow-Well Jet Pump | Deep-Well Jet Pump |
| Motor | 0.75 kW / 1 HP | 0.75 kW / 1 HP |
| Main Application | Shallow well / domestic | Deep well / bore well |
| Max. Suction | Approx. 9 m | Approx. 40 m |
| Impeller | Stainless Steel | Stainless Steel |
| Shaft | AISI 304 | AISI 304 |
| Pump Body | Stainless-steel version | Anti-rust-treated cast iron |
| Garden Irrigation | Yes | Yes |
| Well Water | Yes | Yes, deep-well configuration |
| Deep-Well Ejector | Not applicable | Required for deep-well installation |
The key difference is the deep-well ejector configuration and substantially greater lifting capability of the AJDm75/2H. LEO specifically categorizes the AJDm as a deep-well jet pump.
Installation Considerations
For a deep-well installation, the ejector assembly must be correctly positioned within the well and connected to the pump according to the manufacturer's installation arrangement.
Important considerations include:
- Correct ejector selection
- Correct ejector depth
- Properly sized pipes
- Airtight suction connections
- Proper foot valve/check valve installation
- Minimizing unnecessary pipe bends
- Ensuring adequate well-water level
- Preventing excessive sand entry
- Correct electrical protection
- Correct priming procedure
The pump should never be operated dry because loss of water can damage the mechanical seal and hydraulic components.
Product Description
LEO AJDM75/2H Deep-Well Jet Pump 0.75kW / 1HP is a high-suction jet pump designed for lifting clean water from deep wells, garden irrigation, domestic water supply, pressure boosting and general clean-water transfer. Its deep-well ejector configuration provides a specified maximum suction/lifting capability of approximately 40 m, making it suitable for applications beyond the practical suction range of conventional shallow-well jet pumps.
Powered by a 0.75 kW / 1 HP single-phase motor, the AJDm75/2H provides approximately 47 m maximum head at zero flow, with published performance points ranging from approximately 43 m at 2 L/min to 17 m at 24 L/min. The pump features a stainless-steel impeller, AISI 304 stainless-steel shaft and anti-rust-treated cast-iron pump body and support.
The motor incorporates copper winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection. The LEO AJDm75/2H is an appropriate choice for deep-well water lifting, garden and farm irrigation, domestic water supply, water tank filling and pressure-boosting applications where clean water is required.
SEO Product Title
LEO AJDM75/2H Deep Well Jet Pump 0.75kW 1HP High Suction Water Pump for Garden & Farm
Short Product Description
LEO AJDM75/2H is a 0.75kW / 1HP deep-well jet pump designed for high-suction clean-water applications. With approximately 40 m maximum suction/lifting capability, it is suitable for deep wells, garden irrigation, farm water supply, domestic water supply and pressure boosting. The pump features a stainless-steel impeller, AISI 304 stainless-steel shaft, anti-rust-treated cast-iron body and support, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. Its published performance reaches approximately 47 m head at zero flow, with up to approximately 24 L/min shown in the available performance data.
Inquiry - LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - AJDM 75/2H