B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - AJDM 75/2H



The LEO AJDm75/2H is a deep-well jet pump designed for lifting clean water from deeper wells where a standard shallow-well jet pump may not provide sufficient suction capability. It is suitable for deep-well water supply, garden irrigation, pressure boosting and general clean-water transfer.

The pump uses a 0.75 kW / 1 HP single-phase motor and a deep-well jet/ejector arrangement. Published technical data for the AJDm75/2H gives a maximum suction capability of approximately 40 m, making it substantially different from the standard AJM75S shallow-well jet pump.

Technical Specifications

Specification LEO AJDm75/2H
Brand LEO
Series AJDm
Model AJDm75/2H
Pump Type Deep-Well Jet Pump
Motor Power 0.75 kW / 1 HP
Voltage 220 V
Phase Single Phase
Frequency 50 Hz
Maximum Suction / Lifting Depth Approx. 40 m
Head at 0 L/min Approx. 47 m
Flow at 2 L/min Approx. 43 m head
Flow at 4 L/min Approx. 40 m head
Flow at 6 L/min Approx. 37 m head
Flow at 8 L/min Approx. 34 m head
Flow at 10 L/min Approx. 31 m head
Flow at 12 L/min Approx. 29 m head
Flow at 14 L/min Approx. 27 m head
Flow at 16 L/min Approx. 25 m head
Flow at 18 L/min Approx. 23 m head
Flow at 20 L/min Approx. 21 m head
Flow at 22 L/min Approx. 19 m head
Flow at 24 L/min Approx. 17 m head
Maximum Liquid Temperature +40°C
Maximum Ambient Temperature +40°C
Impeller Stainless Steel
Shaft AISI 304 Stainless Steel
Pump Body Cast Iron, Special Anti-Rust Treatment
Pump Support Cast Iron, Special Anti-Rust Treatment
Motor Winding Copper
Bearing C&U
Thermal Protection Built-In
Insulation Class F
Protection Class IPX4
Duty Continuous

The available technical data specifically identifies the AJDm75/2H as a 0.75 kW / 1 HP deep-well jet pump and provides its head-versus-flow performance points.

Deep-Well Jet Pump Design

The main advantage of the AJDm75/2H is its deep-well configuration.

Unlike a conventional shallow-well jet pump, the AJDm system is designed to work with a deep-well ejector arrangement, allowing water to be lifted from considerably greater depths. LEO classifies the AJDm specifically as a “Jet Pump for Deep Wells.”

This makes the pump suitable for:

  • Deep wells
  • Bore wells with suitable ejector installation
  • Underground water sources
  • Farm water supply
  • Garden irrigation
  • Domestic water supply
  • Pressure boosting
  • Clean-water transfer

The manufacturer specifically lists well-water lifting, garden sprinkler irrigation and running-water pressure boosting among the intended applications.

Maximum Suction Capability

One of the most important specifications of the AJDm75/2H is its approximately 40 m maximum suction/lifting capability when installed with the appropriate deep-well ejector system.

This should not be confused with the approximately 8–9 m suction capability of a conventional surface jet pump.

The actual achievable depth depends on:

  • Well depth
  • Water-table level
  • Ejector installation depth
  • Suction and delivery pipe size
  • Pipe friction losses
  • Number of pipe bends
  • Foot-valve condition
  • Water temperature
  • System leakage
  • Required flow rate

Therefore, the 40 m figure should be treated as the maximum specified suction/lifting capability rather than a guaranteed operating depth at maximum flow.

Performance Curve

The published AJDm75/2H data gives the following approximate relationship between flow and head:

Flow Head
0 L/min 47 m
2 L/min 43 m
4 L/min 40 m
6 L/min 37 m
8 L/min 34 m
10 L/min 31 m
12 L/min 29 m
14 L/min 27 m
16 L/min 25 m
18 L/min 23 m
20 L/min 21 m
22 L/min 19 m
24 L/min 17 m

These figures show that the pump's available discharge head decreases as the water flow increases.

For example, at approximately 10 L/min, the published data indicates about 31 m head, while at approximately 20 L/min, the available head is about 21 m.

Stainless-Steel Impeller

The AJDm75/2H uses a stainless-steel impeller, providing good corrosion resistance and durability for clean-water pumping applications.

The stainless-steel impeller is suitable for:

  • Well water
  • Domestic water
  • Garden irrigation
  • Agricultural water supply
  • Water tank transfer
  • General clean-water applications

The pump is not intended for heavy abrasive liquids, sewage, sludge or water containing significant quantities of solids.

AISI 304 Stainless-Steel Shaft

The pump uses an AISI 304 stainless-steel shaft, providing corrosion resistance and mechanical strength in the rotating assembly.

This complements the stainless-steel impeller and provides a durable hydraulic assembly for normal clean-water applications.

Anti-Rust Pump Body

The AJDm75/2H is constructed with a cast-iron pump body and support receiving special anti-rust treatment.

This is an important distinction for product specifications: the AJDm75/2H should not be described as a completely stainless-steel pump.

Its construction is:

  • Pump body: Cast iron with special anti-rust treatment
  • Pump support: Cast iron with special anti-rust treatment
  • Impeller: Stainless steel
  • Shaft: AISI 304 stainless steel

This combination provides a practical balance between mechanical strength, corrosion resistance and cost.

Motor Specifications

The AJDm75/2H is equipped with a 0.75 kW / 1 HP single-phase motor.

Motor features include:

  • 0.75 kW output
  • 1 HP rating
  • Single-phase operation
  • Copper winding
  • C&U bearing
  • Built-in thermal protector
  • Class F insulation
  • IPX4 protection
  • Maximum ambient temperature +40°C

Copper Motor Winding

The motor uses copper winding, which provides good electrical conductivity and reliable thermal characteristics for continuous water-pumping operation.

Copper winding also contributes to the motor's durability when the pump is operated within its specified electrical and hydraulic operating conditions.

Built-In Thermal Protection

The single-phase motor incorporates a built-in thermal protector. This helps protect the motor winding against overheating caused by abnormal operating conditions such as excessive load or inadequate cooling.

Proper external electrical protection should still be provided according to the installation requirements.

Insulation & Protection

The motor is specified with:

Insulation Class: F
Protection Class: IPX4
Maximum Ambient Temperature: +40°C.

The IPX4 rating provides protection against water splashing from different directions, making the motor suitable for normal protected pump-room and outdoor installations when appropriately installed.

Pumping Medium

The AJDm75/2H is designed for clean water or liquids with physical and chemical properties similar to water. LEO specifies the AJDm series for clean-water transfer and well-water lifting.

Recommended fluids include:

  • Clean well water
  • Fresh water
  • Stored water
  • Irrigation water
  • Domestic water

It should not be selected for:

  • Sewage
  • Sludge
  • Mud
  • Highly abrasive water
  • Fibrous liquids
  • Large suspended solids

If the well contains sand or sediment, appropriate well development and filtration should be considered before operating the pump.

Maximum Liquid Temperature

The published AJDm75/2H specification gives a maximum liquid temperature of +40°C and maximum ambient temperature of +40°C.

For normal well-water and garden-irrigation applications, this is generally more than adequate.

Recommended Applications

Deep-Well Water Supply

The AJDm75/2H is specifically designed for applications where water must be lifted from a deeper well using a suitable ejector system.

Garden Irrigation

It can supply water to sprinklers, hoses and garden irrigation systems when the required flow and pressure are within the pump's performance curve.

Farm Irrigation

The pump is suitable for small-scale agricultural irrigation using clean groundwater.

Domestic Water Supply

It can be used to supply clean water from a suitable well to a residential water system.

Pressure Boosting

The pump can be used to increase water pressure in suitable clean-water systems.

Water Tank Filling

It can transfer clean water from a well or other source into an elevated or storage tank.

Advantages of LEO AJDm75/2H

The main advantages include:

  1. Designed specifically for deep-well applications
  2. Approximately 40 m maximum suction/lifting capability
  3. 0.75 kW / 1 HP motor
  4. Stainless-steel impeller
  5. AISI 304 stainless-steel shaft
  6. Anti-rust-treated cast-iron pump body
  7. Anti-rust-treated pump support
  8. Copper motor winding
  9. C&U bearing
  10. Built-in thermal protection
  11. Class F insulation
  12. IPX4 motor protection
  13. Suitable for garden irrigation
  14. Suitable for well-water lifting
  15. Suitable for domestic water supply
  16. Suitable for pressure boosting
  17. Suitable for clean-water transfer.

AJDM75/2H vs AJM75S

These two models should not be treated as the same pump.

Feature AJM75S AJDm75/2H
Pump Type Shallow-Well Jet Pump Deep-Well Jet Pump
Motor 0.75 kW / 1 HP 0.75 kW / 1 HP
Main Application Shallow well / domestic Deep well / bore well
Max. Suction Approx. 9 m Approx. 40 m
Impeller Stainless Steel Stainless Steel
Shaft AISI 304 AISI 304
Pump Body Stainless-steel version Anti-rust-treated cast iron
Garden Irrigation Yes Yes
Well Water Yes Yes, deep-well configuration
Deep-Well Ejector Not applicable Required for deep-well installation

The key difference is the deep-well ejector configuration and substantially greater lifting capability of the AJDm75/2H. LEO specifically categorizes the AJDm as a deep-well jet pump.

Installation Considerations

For a deep-well installation, the ejector assembly must be correctly positioned within the well and connected to the pump according to the manufacturer's installation arrangement.

Important considerations include:

  • Correct ejector selection
  • Correct ejector depth
  • Properly sized pipes
  • Airtight suction connections
  • Proper foot valve/check valve installation
  • Minimizing unnecessary pipe bends
  • Ensuring adequate well-water level
  • Preventing excessive sand entry
  • Correct electrical protection
  • Correct priming procedure

The pump should never be operated dry because loss of water can damage the mechanical seal and hydraulic components.

Product Description

LEO AJDM75/2H Deep-Well Jet Pump 0.75kW / 1HP is a high-suction jet pump designed for lifting clean water from deep wells, garden irrigation, domestic water supply, pressure boosting and general clean-water transfer. Its deep-well ejector configuration provides a specified maximum suction/lifting capability of approximately 40 m, making it suitable for applications beyond the practical suction range of conventional shallow-well jet pumps.

Powered by a 0.75 kW / 1 HP single-phase motor, the AJDm75/2H provides approximately 47 m maximum head at zero flow, with published performance points ranging from approximately 43 m at 2 L/min to 17 m at 24 L/min. The pump features a stainless-steel impeller, AISI 304 stainless-steel shaft and anti-rust-treated cast-iron pump body and support.

The motor incorporates copper winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection. The LEO AJDm75/2H is an appropriate choice for deep-well water lifting, garden and farm irrigation, domestic water supply, water tank filling and pressure-boosting applications where clean water is required.

SEO Product Title

LEO AJDM75/2H Deep Well Jet Pump 0.75kW 1HP High Suction Water Pump for Garden & Farm

Short Product Description

LEO AJDM75/2H is a 0.75kW / 1HP deep-well jet pump designed for high-suction clean-water applications. With approximately 40 m maximum suction/lifting capability, it is suitable for deep wells, garden irrigation, farm water supply, domestic water supply and pressure boosting. The pump features a stainless-steel impeller, AISI 304 stainless-steel shaft, anti-rust-treated cast-iron body and support, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. Its published performance reaches approximately 47 m head at zero flow, with up to approximately 24 L/min shown in the available performance data.



 Inquiry - LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - AJDM 75/2H