The LEO AJDm110/2H is a 1.1 kW / 1.5 HP deep-well self-priming jet pump designed for lifting clean water from deep wells and suitable for garden irrigation, domestic water supply, pressure boosting and general clean-water transfer.
Unlike conventional shallow-well jet pumps, the AJDm110/2H is designed to work with a deep-well ejector system, providing a published maximum suction/lifting capability of approximately 40 m. LEO identifies the AJDm series specifically for deep-well water lifting, garden sprinkler irrigation and pressure boosting.
Technical Specifications
| Specification | LEO AJDm110/2H |
|---|---|
| Brand | LEO |
| Series | AJDm |
| Model | AJDM110/2H |
| Pump Type | Deep-Well Jet Pump |
| Pump Design | Self-Priming Jet Pump |
| Motor Power | 1.1 kW / 1.5 HP |
| Voltage | 220–240 V |
| Phase | Single Phase |
| Frequency | 50 Hz |
| Flow Range | 5–30 L/min |
| Maximum Flow | 30 L/min |
| Equivalent Maximum Flow | Approx. 1.8 m³/h |
| Head Range | 70–28 m |
| Maximum Head | Approx. 70 m |
| Maximum Suction | 40 m |
| Inlet / Outlet | 1-1/4" × 1" × 1" |
| Impeller | Stainless Steel |
| Shaft | AISI 304 Stainless Steel |
| Pump Body | Cast Iron with Special Anti-Rust Treatment |
| Pump Support | Cast Iron with Special Anti-Rust Treatment |
| Motor Winding | Copper |
| Bearing | C&U |
| Thermal Protection | Built-In |
| Insulation Class | F |
| Protection Class | IPX4 |
| Maximum Liquid Temperature | +40°C / +60°C depending on regional specification |
| Maximum Ambient Temperature | +40°C |
| Mechanical Seal | Carbon / Ceramic |
| Duty | Continuous |
Malaysian product specifications list the AJDM110/2H at 1.1 kW / 1.5 HP, 220 V, 5–30 L/min, 70–28 m head and 40 m maximum suction, with 1-1/4" × 1" × 1" connections.
Deep-Well Pumping Capability
The primary feature of the AJDm110/2H is its deep-well pumping configuration.
The pump is designed for applications where the water level is substantially deeper than the practical suction limit of a conventional surface jet pump. The 40 m maximum suction/lifting specification applies when the pump is installed with the appropriate deep-well ejector arrangement.
Typical applications include:
- Deep wells
- Bore wells with suitable ejector installation
- Underground water sources
- Domestic water supply
- Garden irrigation
- Small farm irrigation
- Water tank filling
- Pressure boosting
- General clean-water transfer
The 40 m figure should be regarded as a maximum specified suction capability, not a guaranteed operating depth at every flow rate. Actual performance depends on the water level, ejector position, pipework, friction losses and required discharge pressure.
Pump Performance
The AJDM110/2H has a published head range of approximately 70–28 m with flow up to approximately 30 L/min.
A representative performance relationship is:
| Flow | Approx. Head |
|---|---|
| 5 L/min | Up to approx. 70 m |
| 10 L/min | High-pressure operating range |
| 15 L/min | Approx. mid-range duty |
| 20 L/min | Reduced head |
| 25 L/min | Lower head |
| 30 L/min | Approx. 28 m |
The exact operating point must be taken from the pump curve for the specific regional version.
It is important to distinguish maximum flow from maximum head. The pump cannot produce 30 L/min at 70 m head; these represent different points on the hydraulic performance curve.
High-Pressure 1.5 HP Motor
The AJDM110/2H uses a 1.1 kW / 1.5 HP single-phase motor, providing greater pumping power than the AJDM75/2H.
The motor is designed for applications requiring substantial lifting pressure, particularly where the water source is located deep underground.
Motor features include:
- 1.1 kW / 1.5 HP
- 220–240 V
- 50 Hz
- Single phase
- Copper winding
- C&U bearing
- Built-in thermal protection
- Class F insulation
- IPX4 protection
LEO's AJDm range uses copper motor windings and built-in thermal protection on the single-phase motor.
Stainless-Steel Impeller
The AJDM110/2H uses a stainless-steel impeller, providing good corrosion resistance and durability when pumping clean water.
This is particularly useful for groundwater applications where corrosion resistance is desirable.
The pump is suitable for:
- Clean well water
- Fresh water
- Irrigation water
- Domestic water
- Storage-tank water
It is not intended for pumping substantial quantities of:
- Sand
- Mud
- Sludge
- Sewage
- Fibrous material
- Abrasive solids
If the well contains significant sand, the well should be properly developed and an appropriate filtration arrangement considered.
AISI 304 Stainless-Steel Shaft
The pump uses an AISI 304 stainless-steel shaft, providing corrosion resistance and mechanical durability within the rotating assembly.
Together with the stainless-steel impeller, the shaft provides a durable hydraulic assembly for clean-water applications.
Anti-Rust Pump Body
The AJDM110/2H does not use a completely stainless-steel pump casing.
Its construction uses:
- Pump body: Cast iron with special anti-rust treatment
- Pump support: Cast iron with special anti-rust treatment
- Impeller: Stainless steel
- Shaft: AISI 304 stainless steel
This construction provides mechanical strength while incorporating corrosion-resistant materials at key wetted/rotating components.
For an accurate website listing, it is preferable to describe the unit as an anti-rust-treated cast-iron deep-well jet pump with stainless-steel impeller and AISI 304 shaft rather than simply calling it a full stainless-steel pump.
Deep-Well Ejector System
The AJDM110/2H is designed around a deep-well jet/ejector system.
The ejector is installed down inside the well, while the pump remains above ground. This configuration allows the pump to operate with a deeper water source than a conventional surface suction pump.
The general arrangement consists of:
Pump → pressure pipe → deep-well ejector → well water → return/suction pipe → pump
Correct ejector installation is critical to achieving the specified deep-well performance.
The installer should follow the manufacturer's recommended pipe sizes and ejector arrangement for the particular installation.
Pipe Connections
The AJDM110/2H is commonly specified with:
Inlet / outlet configuration: 1-1/4" × 1" × 1"
Metric equivalent: approximately 32 mm × 25 mm × 25 mm.
The multiple connections are associated with the deep-well jet/ejector configuration rather than a conventional single suction and discharge arrangement.
Maximum Suction
The AJDM110/2H is rated for approximately 40 m maximum suction/lifting depth.
Actual performance depends on:
- Static water level
- Dynamic water level
- Ejector depth
- Well diameter
- Pipe diameter
- Pipe length
- Number of elbows
- Foot valve condition
- Air leakage
- Water temperature
- Required discharge pressure
For this reason, the pump should be selected based on the actual water level, rather than simply the total physical depth of the well.
Motor Protection
The motor includes a built-in thermal protector for protection against overheating during abnormal operating conditions.
Additional electrical protection should still be provided according to the installation requirements, including suitable circuit protection and proper earthing.
Insulation & Protection
The AJDM110/2H is specified with:
Insulation Class: F
Protection Class: IPX4
Maximum Ambient Temperature: +40°C.
IPX4 provides protection against water splashing, while Class F insulation provides suitable thermal resistance for the motor winding.
Pumping Medium
The AJDm series is intended for clean water or liquids with physical and chemical properties similar to water. LEO specifically lists deep-well water lifting, garden irrigation and pressure boosting as applications.
Recommended applications include:
- Deep-well water
- Clean groundwater
- Domestic water
- Garden irrigation water
- Farm irrigation water
- Storage-tank water
Maximum Temperature
Published specifications vary between regional listings.
One Malaysian listing gives:
Maximum liquid temperature: +40°C
Maximum ambient temperature: +40°C.
Another Malaysian supplier lists the AJDM110/2H with a maximum water temperature of +60°C.
For your website catalogue, the safest specification is to follow the temperature rating printed on the actual stock nameplate/manual supplied with your unit.
Recommended Applications
Deep-Well Water Supply
The AJDM110/2H is specifically designed to lift clean water from deep wells using an appropriate ejector arrangement.
Domestic Water Supply
The 1.5 HP motor and high head capability make it suitable for supplying clean water to homes from suitable deep wells.
Garden Irrigation
It can supply garden sprinklers and irrigation systems where the required flow and pressure fall within the pump curve.
Farm Irrigation
Suitable for small-scale agricultural water supply using clean groundwater.
Water Tank Filling
The pump can transfer well water to storage tanks, elevated tanks or other clean-water reservoirs.
Pressure Boosting
The high head capability makes it suitable for selected water-pressure boosting applications.
Key Advantages
The LEO AJDM110/2H provides:
- 1.1 kW / 1.5 HP motor
- Deep-well self-priming jet-pump design
- Up to approximately 40 m suction/lifting capability
- 5–30 L/min published flow range
- 70–28 m published head range
- Stainless-steel impeller
- AISI 304 stainless-steel shaft
- Anti-rust-treated cast-iron pump body
- Anti-rust-treated cast-iron support
- Copper motor winding
- C&U bearing
- Built-in thermal protector
- Class F insulation
- IPX4 protection
- 1-1/4" × 1" × 1" connections
- Suitable for deep wells
- Suitable for garden irrigation
- Suitable for domestic water supply
- Suitable for pressure boosting
- Suitable for clean-water transfer.
AJDM75/2H vs AJDM110/2H
| Feature | AJDM75/2H | AJDM110/2H |
|---|---|---|
| Motor | 0.75 kW / 1 HP | 1.1 kW / 1.5 HP |
| Voltage | 220 V | 220 V |
| Max. Suction | 40 m | 40 m |
| Flow | Approx. 5–30 L/min* | 5–30 L/min |
| Head | Approx. 50–17 m* | 70–28 m |
| Impeller | Stainless Steel | Stainless Steel |
| Shaft | AISI 304 | AISI 304 |
| Pump Body | Anti-rust-treated cast iron | Anti-rust-treated cast iron |
| Connection | 1-1/4" × 1" × 1" | 1-1/4" × 1" × 1" |
| Application | Deep well / garden | Deep well / garden / higher-pressure duty |
*AJDM75/2H specifications vary among regional listings, with some published curves showing 2–24 L/min and others 5–30 L/min. The exact nameplate and pump curve should be used for the supplied model.
The primary advantage of the AJDM110/2H is its higher 1.5 HP motor and substantially higher head capability, while retaining approximately 40 m maximum suction.
Important Installation Notes
For deep-well installations, correct system design is particularly important.
The following should be checked before installation:
- Confirm the actual static and dynamic water level.
- Install the ejector at the correct depth.
- Use suitable pressure and suction pipe sizes.
- Ensure all suction connections are completely airtight.
- Install a suitable foot valve/check valve.
- Minimize unnecessary pipe bends.
- Ensure the well can provide the required flow.
- Prime the pump correctly before starting.
- Never operate the pump dry.
- Provide appropriate electrical overload and earth protection.
A deep-well pump's performance is determined by the water level under operating conditions, not simply the measured depth from ground level to the bottom of the well.
Product Description
LEO AJDM110/2H Deep-Well Jet Pump 1.1kW / 1.5HP 220V is a high-pressure self-priming jet pump designed for lifting clean water from deep wells using a suitable deep-well ejector system. With approximately 40 m maximum suction/lifting capability, the AJDM110/2H is suitable for deep-well water supply, garden irrigation, farm irrigation, domestic water supply, water tank filling and pressure boosting.
Powered by a 1.1 kW / 1.5 HP single-phase motor, the pump provides approximately 5–30 L/min flow with a 70–28 m head range, offering substantially higher pressure capability than the smaller AJDM75/2H. It features a stainless-steel impeller, AISI 304 stainless-steel shaft and anti-rust-treated cast-iron pump body and support.
The motor incorporates copper winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection. With 1-1/4" × 1" × 1" deep-well connections, the LEO AJDM110/2H is a practical choice for demanding clean-water lifting applications where a conventional shallow-well jet pump is insufficient.
SEO Product Title
LEO AJDM110/2H Deep Well Jet Pump 1.1kW 1.5HP 220V High Suction Water Pump for Garden & Farm
Short Product Description
LEO AJDM110/2H is a 1.1kW / 1.5HP 220V deep-well self-priming jet pump designed for lifting clean water from deep wells up to approximately 40 m suction/lifting depth with the appropriate ejector system. It provides approximately 5–30 L/min flow and 70–28 m head, featuring a stainless-steel impeller, AISI 304 stainless-steel shaft, anti-rust-treated cast-iron pump body, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. With 1-1/4" × 1" × 1" connections, it is suitable for deep-well water supply, garden irrigation, farm irrigation, domestic water supply, tank filling and pressure boosting.
Inquiry - LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - AJDM 110/2H