B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - AJDM 110/2H



The LEO AJDm110/2H is a 1.1 kW / 1.5 HP deep-well self-priming jet pump designed for lifting clean water from deep wells and suitable for garden irrigation, domestic water supply, pressure boosting and general clean-water transfer.

Unlike conventional shallow-well jet pumps, the AJDm110/2H is designed to work with a deep-well ejector system, providing a published maximum suction/lifting capability of approximately 40 m. LEO identifies the AJDm series specifically for deep-well water lifting, garden sprinkler irrigation and pressure boosting.

Technical Specifications

Specification LEO AJDm110/2H
Brand LEO
Series AJDm
Model AJDM110/2H
Pump Type Deep-Well Jet Pump
Pump Design Self-Priming Jet Pump
Motor Power 1.1 kW / 1.5 HP
Voltage 220–240 V
Phase Single Phase
Frequency 50 Hz
Flow Range 5–30 L/min
Maximum Flow 30 L/min
Equivalent Maximum Flow Approx. 1.8 m³/h
Head Range 70–28 m
Maximum Head Approx. 70 m
Maximum Suction 40 m
Inlet / Outlet 1-1/4" × 1" × 1"
Impeller Stainless Steel
Shaft AISI 304 Stainless Steel
Pump Body Cast Iron with Special Anti-Rust Treatment
Pump Support Cast Iron with Special Anti-Rust Treatment
Motor Winding Copper
Bearing C&U
Thermal Protection Built-In
Insulation Class F
Protection Class IPX4
Maximum Liquid Temperature +40°C / +60°C depending on regional specification
Maximum Ambient Temperature +40°C
Mechanical Seal Carbon / Ceramic
Duty Continuous

Malaysian product specifications list the AJDM110/2H at 1.1 kW / 1.5 HP, 220 V, 5–30 L/min, 70–28 m head and 40 m maximum suction, with 1-1/4" × 1" × 1" connections.

Deep-Well Pumping Capability

The primary feature of the AJDm110/2H is its deep-well pumping configuration.

The pump is designed for applications where the water level is substantially deeper than the practical suction limit of a conventional surface jet pump. The 40 m maximum suction/lifting specification applies when the pump is installed with the appropriate deep-well ejector arrangement.

Typical applications include:

  • Deep wells
  • Bore wells with suitable ejector installation
  • Underground water sources
  • Domestic water supply
  • Garden irrigation
  • Small farm irrigation
  • Water tank filling
  • Pressure boosting
  • General clean-water transfer

The 40 m figure should be regarded as a maximum specified suction capability, not a guaranteed operating depth at every flow rate. Actual performance depends on the water level, ejector position, pipework, friction losses and required discharge pressure.

Pump Performance

The AJDM110/2H has a published head range of approximately 70–28 m with flow up to approximately 30 L/min.

A representative performance relationship is:

Flow Approx. Head
5 L/min Up to approx. 70 m
10 L/min High-pressure operating range
15 L/min Approx. mid-range duty
20 L/min Reduced head
25 L/min Lower head
30 L/min Approx. 28 m

The exact operating point must be taken from the pump curve for the specific regional version.

It is important to distinguish maximum flow from maximum head. The pump cannot produce 30 L/min at 70 m head; these represent different points on the hydraulic performance curve.

High-Pressure 1.5 HP Motor

The AJDM110/2H uses a 1.1 kW / 1.5 HP single-phase motor, providing greater pumping power than the AJDM75/2H.

The motor is designed for applications requiring substantial lifting pressure, particularly where the water source is located deep underground.

Motor features include:

  • 1.1 kW / 1.5 HP
  • 220–240 V
  • 50 Hz
  • Single phase
  • Copper winding
  • C&U bearing
  • Built-in thermal protection
  • Class F insulation
  • IPX4 protection

LEO's AJDm range uses copper motor windings and built-in thermal protection on the single-phase motor.

Stainless-Steel Impeller

The AJDM110/2H uses a stainless-steel impeller, providing good corrosion resistance and durability when pumping clean water.

This is particularly useful for groundwater applications where corrosion resistance is desirable.

The pump is suitable for:

  • Clean well water
  • Fresh water
  • Irrigation water
  • Domestic water
  • Storage-tank water

It is not intended for pumping substantial quantities of:

  • Sand
  • Mud
  • Sludge
  • Sewage
  • Fibrous material
  • Abrasive solids

If the well contains significant sand, the well should be properly developed and an appropriate filtration arrangement considered.

AISI 304 Stainless-Steel Shaft

The pump uses an AISI 304 stainless-steel shaft, providing corrosion resistance and mechanical durability within the rotating assembly.

Together with the stainless-steel impeller, the shaft provides a durable hydraulic assembly for clean-water applications.

Anti-Rust Pump Body

The AJDM110/2H does not use a completely stainless-steel pump casing.

Its construction uses:

  • Pump body: Cast iron with special anti-rust treatment
  • Pump support: Cast iron with special anti-rust treatment
  • Impeller: Stainless steel
  • Shaft: AISI 304 stainless steel

This construction provides mechanical strength while incorporating corrosion-resistant materials at key wetted/rotating components.

For an accurate website listing, it is preferable to describe the unit as an anti-rust-treated cast-iron deep-well jet pump with stainless-steel impeller and AISI 304 shaft rather than simply calling it a full stainless-steel pump.

Deep-Well Ejector System

The AJDM110/2H is designed around a deep-well jet/ejector system.

The ejector is installed down inside the well, while the pump remains above ground. This configuration allows the pump to operate with a deeper water source than a conventional surface suction pump.

The general arrangement consists of:

Pump → pressure pipe → deep-well ejector → well water → return/suction pipe → pump

Correct ejector installation is critical to achieving the specified deep-well performance.

The installer should follow the manufacturer's recommended pipe sizes and ejector arrangement for the particular installation.

Pipe Connections

The AJDM110/2H is commonly specified with:

Inlet / outlet configuration: 1-1/4" × 1" × 1"
Metric equivalent: approximately 32 mm × 25 mm × 25 mm.

The multiple connections are associated with the deep-well jet/ejector configuration rather than a conventional single suction and discharge arrangement.

Maximum Suction

The AJDM110/2H is rated for approximately 40 m maximum suction/lifting depth.

Actual performance depends on:

  • Static water level
  • Dynamic water level
  • Ejector depth
  • Well diameter
  • Pipe diameter
  • Pipe length
  • Number of elbows
  • Foot valve condition
  • Air leakage
  • Water temperature
  • Required discharge pressure

For this reason, the pump should be selected based on the actual water level, rather than simply the total physical depth of the well.

Motor Protection

The motor includes a built-in thermal protector for protection against overheating during abnormal operating conditions.

Additional electrical protection should still be provided according to the installation requirements, including suitable circuit protection and proper earthing.

Insulation & Protection

The AJDM110/2H is specified with:

Insulation Class: F
Protection Class: IPX4
Maximum Ambient Temperature: +40°C.

IPX4 provides protection against water splashing, while Class F insulation provides suitable thermal resistance for the motor winding.

Pumping Medium

The AJDm series is intended for clean water or liquids with physical and chemical properties similar to water. LEO specifically lists deep-well water lifting, garden irrigation and pressure boosting as applications.

Recommended applications include:

  • Deep-well water
  • Clean groundwater
  • Domestic water
  • Garden irrigation water
  • Farm irrigation water
  • Storage-tank water

Maximum Temperature

Published specifications vary between regional listings.

One Malaysian listing gives:

Maximum liquid temperature: +40°C
Maximum ambient temperature: +40°C.

Another Malaysian supplier lists the AJDM110/2H with a maximum water temperature of +60°C.

For your website catalogue, the safest specification is to follow the temperature rating printed on the actual stock nameplate/manual supplied with your unit.

Recommended Applications

Deep-Well Water Supply

The AJDM110/2H is specifically designed to lift clean water from deep wells using an appropriate ejector arrangement.

Domestic Water Supply

The 1.5 HP motor and high head capability make it suitable for supplying clean water to homes from suitable deep wells.

Garden Irrigation

It can supply garden sprinklers and irrigation systems where the required flow and pressure fall within the pump curve.

Farm Irrigation

Suitable for small-scale agricultural water supply using clean groundwater.

Water Tank Filling

The pump can transfer well water to storage tanks, elevated tanks or other clean-water reservoirs.

Pressure Boosting

The high head capability makes it suitable for selected water-pressure boosting applications.

Key Advantages

The LEO AJDM110/2H provides:

  1. 1.1 kW / 1.5 HP motor
  2. Deep-well self-priming jet-pump design
  3. Up to approximately 40 m suction/lifting capability
  4. 5–30 L/min published flow range
  5. 70–28 m published head range
  6. Stainless-steel impeller
  7. AISI 304 stainless-steel shaft
  8. Anti-rust-treated cast-iron pump body
  9. Anti-rust-treated cast-iron support
  10. Copper motor winding
  11. C&U bearing
  12. Built-in thermal protector
  13. Class F insulation
  14. IPX4 protection
  15. 1-1/4" × 1" × 1" connections
  16. Suitable for deep wells
  17. Suitable for garden irrigation
  18. Suitable for domestic water supply
  19. Suitable for pressure boosting
  20. Suitable for clean-water transfer.

AJDM75/2H vs AJDM110/2H

Feature AJDM75/2H AJDM110/2H
Motor 0.75 kW / 1 HP 1.1 kW / 1.5 HP
Voltage 220 V 220 V
Max. Suction 40 m 40 m
Flow Approx. 5–30 L/min* 5–30 L/min
Head Approx. 50–17 m* 70–28 m
Impeller Stainless Steel Stainless Steel
Shaft AISI 304 AISI 304
Pump Body Anti-rust-treated cast iron Anti-rust-treated cast iron
Connection 1-1/4" × 1" × 1" 1-1/4" × 1" × 1"
Application Deep well / garden Deep well / garden / higher-pressure duty

*AJDM75/2H specifications vary among regional listings, with some published curves showing 2–24 L/min and others 5–30 L/min. The exact nameplate and pump curve should be used for the supplied model.

The primary advantage of the AJDM110/2H is its higher 1.5 HP motor and substantially higher head capability, while retaining approximately 40 m maximum suction.

Important Installation Notes

For deep-well installations, correct system design is particularly important.

The following should be checked before installation:

  • Confirm the actual static and dynamic water level.
  • Install the ejector at the correct depth.
  • Use suitable pressure and suction pipe sizes.
  • Ensure all suction connections are completely airtight.
  • Install a suitable foot valve/check valve.
  • Minimize unnecessary pipe bends.
  • Ensure the well can provide the required flow.
  • Prime the pump correctly before starting.
  • Never operate the pump dry.
  • Provide appropriate electrical overload and earth protection.

A deep-well pump's performance is determined by the water level under operating conditions, not simply the measured depth from ground level to the bottom of the well.

Product Description

LEO AJDM110/2H Deep-Well Jet Pump 1.1kW / 1.5HP 220V is a high-pressure self-priming jet pump designed for lifting clean water from deep wells using a suitable deep-well ejector system. With approximately 40 m maximum suction/lifting capability, the AJDM110/2H is suitable for deep-well water supply, garden irrigation, farm irrigation, domestic water supply, water tank filling and pressure boosting.

Powered by a 1.1 kW / 1.5 HP single-phase motor, the pump provides approximately 5–30 L/min flow with a 70–28 m head range, offering substantially higher pressure capability than the smaller AJDM75/2H. It features a stainless-steel impeller, AISI 304 stainless-steel shaft and anti-rust-treated cast-iron pump body and support.

The motor incorporates copper winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection. With 1-1/4" × 1" × 1" deep-well connections, the LEO AJDM110/2H is a practical choice for demanding clean-water lifting applications where a conventional shallow-well jet pump is insufficient.

SEO Product Title

LEO AJDM110/2H Deep Well Jet Pump 1.1kW 1.5HP 220V High Suction Water Pump for Garden & Farm

Short Product Description

LEO AJDM110/2H is a 1.1kW / 1.5HP 220V deep-well self-priming jet pump designed for lifting clean water from deep wells up to approximately 40 m suction/lifting depth with the appropriate ejector system. It provides approximately 5–30 L/min flow and 70–28 m head, featuring a stainless-steel impeller, AISI 304 stainless-steel shaft, anti-rust-treated cast-iron pump body, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. With 1-1/4" × 1" × 1" connections, it is suitable for deep-well water supply, garden irrigation, farm irrigation, domestic water supply, tank filling and pressure boosting.



 Inquiry - LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - AJDM 110/2H