B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - AJDM 75/4H



The LEO AJDM75/4H is a 0.75 kW / 1 HP deep-well jet pump designed for lifting clean water from wells and for applications including garden irrigation, domestic water supply, water tank filling, pressure boosting and general clean-water transfer. It uses a deep-well ejector/venturi system that allows it to operate at substantially greater suction depths than a conventional shallow-well jet pump.

LEO classifies the AJDm series as jet pumps for deep wells, with applications including well-water lifting, garden sprinkler irrigation and running-water pressure boosting.

Technical Specifications

Specification LEO AJDM75/4H
Brand LEO
Series AJDm
Model AJDM75/4H
Pump Type Deep-Well Jet Pump
Pump Design Self-Priming Jet Pump
Motor Power 0.75 kW / 1 HP
Voltage 220 V
Phase Single Phase
Frequency 50 Hz
Maximum Head Approx. 48 m
Maximum Suction Up to approx. 40 m*
Flow Approx. 2–24 L/min*
Equivalent Maximum Flow Approx. 1.44 m³/h
Main Connection 1-1/4"
Ejector Connections 1" × 1" × 1"
Impeller Stainless Steel
Shaft AISI 304 Stainless Steel
Pump Body Cast Iron with Special Anti-Rust Treatment
Pump Support Anti-Rust-Treated Cast Iron
Nozzle PPO
Venturi Tube PPO
Ejector HT200
Mechanical Seal Carbon / Ceramic
O-Ring NBR
Motor Winding Copper
Bearing C&U
Thermal Protection Built-In
Insulation Class F
Protection Class IPX4
Maximum Ambient Temperature +40°C
Maximum Liquid Temperature +40°C
Duty Continuous

*Maximum suction and flow can vary by regional specification, ejector arrangement and installation conditions. The actual manufacturer's pump curve/nameplate should be used for final selection.

Deep-Well Pump Design

The principal advantage of the AJDM75/4H is its deep-well configuration.

A conventional surface jet pump is generally limited by atmospheric pressure and the practical suction capability of the pump. The AJDM75/4H instead uses a deep-well ejector, with the ejector installed down in the well and the pump remaining above ground.

The ejector circulates pressurized water through a nozzle and venturi to generate the suction effect required to lift groundwater.

This configuration makes the AJDM75/4H suitable for:

  • Deep wells
  • Bore wells with suitable ejector installation
  • Underground water sources
  • Domestic water supply
  • Garden irrigation
  • Small farm irrigation
  • Water tank filling
  • Pressure boosting

LEO specifically identifies the AJDm series for well-water lifting, garden sprinkler irrigation and running-water pressure boosting.

Motor Power – 0.75 kW / 1 HP

The AJDM75/4H is powered by a 0.75 kW / 1 HP single-phase motor.

This places it above the AJDM55/4H 0.55 kW / 0.75 HP model and makes it suitable where somewhat greater pressure and pumping capacity are required.

The motor incorporates:

  • 0.75 kW output
  • 1 HP rating
  • 220 V operation
  • Single-phase configuration
  • Copper winding
  • C&U bearing
  • Built-in thermal protection
  • Class F insulation
  • IPX4 protection

The 1 HP motor provides a useful balance between energy consumption, pressure and water delivery for domestic and small irrigation installations.

Pump Performance

The AJDM75/4H is intended for applications requiring both suction capability and useful discharge pressure.

Published regional specifications commonly show approximately 2–24 L/min flow with a maximum head in the region of 48 m.

The performance should be understood as a pump curve rather than a single fixed output:

Operating Condition Expected Behaviour
Low flow Higher available head
Medium flow Moderate head and useful water delivery
High flow Lower available head
Deep suction Lower practical discharge flow
Greater discharge pressure Lower available flow

Therefore, maximum head and maximum flow cannot be achieved simultaneously.

For example, a system requiring high lifting depth plus high discharge pressure may produce considerably less flow than the pump's maximum free-flow rating.

Maximum Suction / Deep-Well Capability

The AJDM75/4H is designed for deep-well applications and can achieve substantially greater lifting depths than standard surface jet pumps when correctly installed with the appropriate ejector.

LEO's AJDm documentation identifies the series as a deep-well jet pump.

Some regional specifications quote up to approximately 40 m maximum suction, while other AJDM75/4H listings provide lower figures depending on the ejector configuration and product version.

The actual achievable depth depends on:

  • Static water level
  • Dynamic water level
  • Ejector depth
  • Ejector design
  • Pressure-pipe diameter
  • Suction/return-pipe diameter
  • Total pipe length
  • Pipe friction
  • Number of elbows
  • Foot valve
  • Water temperature
  • Required discharge pressure

The maximum advertised suction should therefore not be interpreted as guaranteed 40 m operation at maximum flow.

Stainless-Steel Impeller

The AJDM75/4H incorporates a stainless-steel impeller.

The stainless-steel hydraulic component provides good corrosion resistance for clean-water and groundwater applications.

It is suitable for:

  • Clean well water
  • Fresh water
  • Domestic water
  • Irrigation water
  • Garden water
  • Storage-tank water

The pump should not be selected for heavy solids, sewage, sludge or highly abrasive liquids.

AISI 304 Stainless-Steel Shaft

The rotating assembly uses an AISI 304 stainless-steel shaft.

This provides:

  • Corrosion resistance
  • Good mechanical strength
  • Durable rotating operation
  • Compatibility with clean-water applications

The combination of stainless-steel impeller + AISI 304 shaft is particularly useful for groundwater pumping.

Anti-Rust Cast-Iron Pump Body

The AJDM75/4H should not be described as a fully stainless-steel pump.

Its construction consists of:

Pump body: Cast iron with special anti-rust treatment
Pump support: Cast iron with anti-rust treatment
Impeller: Stainless steel
Shaft: AISI 304 stainless steel

This provides mechanical strength while using stainless steel in important hydraulic and rotating components.

For website listings, a technically accurate description would be:

“LEO deep-well jet pump with stainless-steel impeller and AISI 304 stainless-steel shaft.”

Ejector & Venturi System

The deep-well ejector is an important part of the AJDM75/4H system.

The assembly uses a nozzle and venturi arrangement to generate the suction required to lift water from the deep well.

Typical construction includes:

  • Nozzle: PPO
  • Venturi tube: PPO
  • Ejector: HT200
  • O-ring: NBR
  • Mechanical seal: Carbon/Ceramic

The ejector must be installed at the correct depth and connected according to the manufacturer's recommended piping configuration.

Incorrect ejector depth or pipe sizing can significantly reduce the pump's performance.

Connection Sizes

The AJDM75/4H uses a deep-well connection arrangement rather than the simple single suction/discharge arrangement found on many standard jet pumps.

Common specifications include:

Connection Size
Main pump connection 1-1/4"
Ejector/auxiliary connections 1" × 1" × 1"

The actual piping arrangement should follow the supplied LEO installation diagram.

Because deep-well jet pumps use recirculation through the ejector, correct pipe identification is important during installation.

Mechanical Seal

The pump uses a carbon/ceramic mechanical seal.

The mechanical seal provides a water-tight barrier around the rotating shaft and prevents water from escaping from the pump chamber.

Proper priming and avoiding dry running are important for extending mechanical-seal service life.

Motor Protection

The AJDM75/4H has a built-in thermal protector in the single-phase motor.

This helps protect the winding against excessive temperature caused by abnormal operating conditions.

However, the built-in thermal protector should not be regarded as a substitute for proper electrical installation.

Recommended installation should include appropriate:

  • Circuit protection
  • Earthing
  • Cable sizing
  • Isolation switch
  • Overload protection where required

Insulation & Protection

The motor is specified with:

Insulation Class: F
Protection Class: IPX4
Maximum Ambient Temperature: +40°C

Class F insulation provides suitable thermal resistance for the motor winding, while IPX4 provides protection against water splashing.

The pump should nevertheless be installed in a suitable location protected from flooding and direct exposure to severe weather.

Pumping Medium

The AJDM75/4H is intended for clean water and liquids with physical and chemical properties similar to water.

Suitable applications include:

  • Groundwater
  • Well water
  • Fresh water
  • Garden irrigation water
  • Domestic water
  • Agricultural irrigation water
  • Storage-tank water

It is not suitable for:

  • Sewage
  • Sludge
  • Mud
  • Heavy sand
  • Fibrous wastewater
  • Highly abrasive liquids
  • Large suspended solids

If the water source contains sand, proper well development and filtration should be considered.

Maximum Temperature

The AJDm series is intended for normal clean-water applications, with regional specifications commonly indicating a maximum liquid temperature around +40°C.

Some local product listings may specify a higher temperature limit depending on the exact model/version. For catalogue accuracy, use the temperature rating printed on the actual pump nameplate or manufacturer documentation supplied with your stock.

Recommended Applications

The AJDM75/4H is suitable for a wide range of water-supply applications.

Deep-Well Water Lifting

Its primary purpose is lifting clean water from wells using a suitable deep-well ejector.

Garden Irrigation

Suitable for garden sprinklers, hoses and small irrigation systems where the required flow and pressure fall within the pump curve.

Domestic Water Supply

Can be used to supply clean water from a well to a house or small building.

Water Tank Filling

Suitable for transferring groundwater into storage or elevated tanks.

Farm Irrigation

The 1 HP motor makes it suitable for smaller agricultural irrigation applications.

Pressure Boosting

Can be used to increase water pressure in suitable clean-water systems.

Key Advantages

The LEO AJDM75/4H offers:

  1. 0.75 kW / 1 HP motor
  2. Deep-well jet-pump configuration
  3. Self-priming operation
  4. Deep-well ejector system
  5. Stainless-steel impeller
  6. AISI 304 stainless-steel shaft
  7. Anti-rust-treated cast-iron pump body
  8. PPO nozzle and venturi
  9. HT200 ejector
  10. Carbon/ceramic mechanical seal
  11. Copper motor winding
  12. C&U bearing
  13. Built-in thermal protection
  14. Class F insulation
  15. IPX4 protection
  16. Suitable for deep wells
  17. Suitable for garden irrigation
  18. Suitable for domestic water supply
  19. Suitable for tank filling
  20. Suitable for pressure boosting

AJDM55/4H vs AJDM75/4H

Feature AJDM55/4H AJDM75/4H
Motor Power 0.55 kW / 0.75 HP 0.75 kW / 1 HP
Pump Type Deep-Well Jet Deep-Well Jet
Impeller Stainless Steel Stainless Steel
Shaft AISI 304 AISI 304
Pump Body Anti-Rust Cast Iron Anti-Rust Cast Iron
Motor Winding Copper Copper
Deep-Well Ejector Yes Yes
Relative Capacity Lower Higher
Relative Pressure Lower Higher
Recommended Duty Small installations Small-to-medium installations

The AJDM75/4H is the more powerful option, making it preferable where the system requires higher pressure or greater water delivery than the 0.75 HP AJDM55/4H can provide.

Installation Requirements

Correct installation is essential for deep-well jet pumps.

Before commissioning the AJDM75/4H:

  • Confirm the actual static water level.
  • Confirm the dynamic water level while pumping.
  • Install the ejector at the correct depth.
  • Use the recommended pipe sizes.
  • Ensure all pipe joints are airtight.
  • Install the required foot valve/check valve.
  • Minimize unnecessary pipe bends.
  • Confirm the well can provide adequate water.
  • Prime the pump completely.
  • Never operate the pump dry.
  • Provide proper electrical protection and earthing.

A deep-well jet pump's actual performance is determined by the operating water level and complete hydraulic system, not simply the total depth of the well.

Product Description

LEO AJDM75/4H Deep-Well Jet Pump 0.75kW / 1HP is a self-priming deep-well water pump designed for lifting clean water from wells and supplying water for garden irrigation, domestic water supply, water tank filling, small-scale agricultural irrigation and pressure boosting. Its deep-well ejector and venturi system allows it to operate at substantially greater lifting depths than conventional shallow-well jet pumps.

The pump features a stainless-steel impeller, AISI 304 stainless-steel shaft and anti-rust-treated cast-iron pump body, together with a PPO nozzle and venturi system and HT200 ejector. The 0.75 kW / 1 HP single-phase motor incorporates copper winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection.

With a published maximum head of approximately 48 m and flow capability dependent on the operating point and ejector installation, the AJDM75/4H is a practical choice for deep-well water lifting, household water supply, garden irrigation and clean-water pressure boosting.

SEO Product Title

LEO AJDM75/4H Deep Well Jet Pump 0.75kW 1HP Self-Priming Water Pump for Garden & Irrigation

Short Product Description

LEO AJDM75/4H is a 0.75kW / 1HP deep-well self-priming jet pump designed for clean-water lifting from deep wells, garden irrigation, domestic water supply, tank filling and pressure boosting. It features a stainless-steel impeller, AISI 304 stainless-steel shaft, anti-rust-treated cast-iron pump body, PPO venturi/nozzle system, HT200 ejector, carbon/ceramic mechanical seal and copper-wound motor. With approximately 48 m maximum head and deep-well suction capability dependent on the ejector and installation configuration, the AJDM75/4H is suitable for domestic, garden and small agricultural water systems.



 Inquiry - LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - AJDM 75/4H