The LEO AJDM110/4H is a 1.1 kW / 1.5 HP single-phase deep-well jet pump designed for lifting clean water from wells and supplying water for domestic applications, garden irrigation, small-scale agricultural irrigation, water tank filling and pressure boosting.
It combines a surface-mounted centrifugal pump with a deep-well ejector/venturi system, allowing it to handle significantly deeper water sources than a conventional shallow-well jet pump. LEO specifies the AJDm series for transferring clean water, lifting water from wells, garden sprinkler irrigation, running-water pressure boosting and supporting equipment.
Technical Specifications
| Specification | LEO AJDM110/4H |
|---|---|
| Brand | LEO |
| Series | AJDm |
| Model | AJDM110/4H |
| Pump Type | Deep-Well Jet Pump |
| Pump Design | Self-Priming Jet Pump |
| Motor Power | 1.1 kW / 1.5 HP |
| Voltage | 220 V |
| Phase | Single Phase |
| Frequency | 50 Hz |
| Maximum Flow | Up to 90 L/min* |
| Maximum Head | Approx. 80 m* |
| Maximum Suction | 40 m |
| Main Inlet/Outlet | 1-1/4" × 1" × 1" |
| Impeller | Stainless Steel |
| Shaft | AISI 304 Stainless Steel |
| Pump Body | Cast Iron with Special Anti-Rust Treatment |
| Pump Support | Cast Iron with Special Anti-Rust Treatment |
| Motor Winding | Copper |
| Bearing | C&U |
| Mechanical Seal | Carbon / Ceramic |
| Thermal Protection | Built-In |
| Insulation Class | F |
| Protection Class | IPX4 |
| Maximum Liquid Temperature | +40°C |
| Maximum Ambient Temperature | +40°C |
| Application | Deep Well, Garden Irrigation, Domestic Water Supply, Pressure Boosting |
*Published specifications vary between regional AJDM110/4H listings. A Malaysian supplier specifies 5–90 L/min and 80–28 m head, while another current Malaysian listing gives 90 L/min and 95 m maximum head. For your website catalogue, the actual nameplate and pump curve supplied with your stock should be treated as the final specification.
Deep-Well Pumping System
The key feature of the AJDM110/4H is its deep-well jet configuration.
Instead of relying solely on the surface pump to create suction, the system uses an ejector assembly installed down inside the well. Pressurized water is circulated through the ejector's nozzle and venturi, generating the suction effect needed to lift groundwater toward the surface.
This makes the AJDM110/4H particularly suitable where:
- The groundwater level is relatively deep.
- A conventional shallow-well pump cannot provide sufficient suction.
- A surface-mounted pump is preferred for easier maintenance.
- Domestic water needs to be supplied from a deep well.
- Garden or agricultural irrigation requires additional pressure.
LEO specifically identifies the AJDm range as suitable for lifting water from wells, garden sprinkler irrigation and pressure boosting.
1.1 kW / 1.5 HP Motor
The AJDM110/4H uses a 1.1 kW / 1.5 HP single-phase motor, making it the higher-powered option in comparison with the AJDM55/4H and AJDM75/4H models.
The motor is designed to provide the additional power required for:
- Greater lifting requirements
- Higher discharge pressure
- Larger domestic water systems
- Garden irrigation
- Small agricultural irrigation
- Pressure boosting
The motor uses copper winding and a C&U bearing, with built-in thermal protection for the single-phase motor.
Pump Performance
A Malaysian supplier publishes the AJDM110/4H with a performance range of approximately:
Flow: 5–90 L/min
Head: 80–28 m.
This means the pump does not produce 90 L/min at 80 m head. As with centrifugal pumps generally, head decreases as flow increases.
A simplified interpretation is:
| Operating Condition | Pump Behaviour |
|---|---|
| Very low flow | Highest available head |
| Low flow | High pressure |
| Medium flow | Balanced pressure and delivery |
| High flow | Reduced head |
| Maximum flow | Lowest operating head |
For system design, the required operating point should be determined from the manufacturer's pump curve rather than using the maximum flow and maximum head simultaneously.
Maximum Suction – 40 m
The AJDM110/4H is specified with maximum suction of approximately 40 m in current Malaysian product information.
This is one of the main reasons to select the AJDM110/4H instead of a conventional shallow-well jet pump.
However, 40 m is a maximum catalogue specification and should not be interpreted as guaranteed 40 m pumping depth at maximum flow.
Actual performance depends on:
- Static water level
- Dynamic water level
- Ejector installation depth
- Well diameter
- Ejector efficiency
- Suction/return pipe size
- Pressure pipe size
- Total pipe length
- Pipe friction losses
- Number of elbows
- Foot valve condition
- Water temperature
- Required discharge pressure
The dynamic water level is especially important because the water level can fall significantly when the well is being pumped.
Stainless-Steel Impeller
The AJDM110/4H incorporates a stainless-steel impeller.
The stainless-steel impeller provides good corrosion resistance and durability for clean-water applications.
It is suitable for:
- Clean well water
- Fresh water
- Domestic water
- Garden irrigation
- Agricultural irrigation
- Storage-tank water
The pump should not be used for heavily contaminated water, sewage, sludge or liquids containing substantial abrasive solids.
AISI 304 Stainless-Steel Shaft
The pump uses an AISI 304 stainless-steel shaft.
This provides good corrosion resistance and mechanical durability in the rotating assembly.
The combination of:
AISI 304 shaft + stainless-steel impeller
provides a robust hydraulic assembly for clean-water pumping.
Anti-Rust Cast-Iron Pump Body
The AJDM110/4H is not a completely stainless-steel pump.
Its principal construction includes:
- Pump body: Cast iron with special anti-rust treatment
- Pump support: Cast iron with special anti-rust treatment
- Impeller: Stainless steel
- Shaft: AISI 304 stainless steel
This construction provides mechanical rigidity while incorporating corrosion-resistant materials in important hydraulic components.
For an accurate product listing, describe it as a:
“Deep-well jet pump with stainless-steel impeller and AISI 304 stainless-steel shaft.”
Ejector and Venturi System
The AJDM110/4H operates using a deep-well ejector system.
The ejector consists of a nozzle, venturi/diffuser components and associated hydraulic passages. Pressurized water from the pump is directed through the ejector, creating a low-pressure zone that draws additional water from the well.
This principle allows the pump to lift water from a deeper source while keeping the motor and main pump assembly above ground.
Correct ejector installation is critical. Incorrect pipe sizing, air leakage or unsuitable ejector depth can cause:
- Loss of prime
- Low water delivery
- Excessive cycling
- Reduced pressure
- Poor deep-well performance
Connection Sizes
Current Malaysian product information specifies:
Inlet / Outlet: 1-1/4" × 1" × 1".
Another current listing simplifies the main pump connection to:
1-1/4" × 1" (32 mm × 25 mm).
Because this is a deep-well jet pump, the multiple connections are associated with the pump/ejector hydraulic arrangement.
The installer should follow the LEO connection diagram supplied with the particular unit rather than assuming all three ports serve the same function.
Mechanical Seal
The AJDM110/4H uses a carbon/ceramic mechanical seal.
The mechanical seal prevents water from escaping along the motor shaft between the hydraulic chamber and motor assembly.
To maximize seal life:
- Prime the pump before operation.
- Never run the pump dry.
- Avoid excessive air entering the suction system.
- Ensure the water source is adequate.
- Avoid operating outside the manufacturer's recommended conditions.
Copper Motor Winding
The motor uses copper winding.
Copper winding provides good electrical conductivity and is widely used in continuous-duty water-pump motors.
The motor is designed for normal clean-water pumping applications and incorporates thermal protection for the single-phase configuration.
Built-In Thermal Protection
The single-phase motor includes a built-in thermal protector.
This protects the motor against overheating caused by abnormal operating conditions.
Nevertheless, proper external electrical protection remains important. Installation should include appropriate circuit protection, earthing, isolation and correctly sized cabling.
Insulation and Protection
The AJDM110/4H is specified with:
Insulation Class: F
Protection Class: IPX4
Maximum Ambient Temperature: +40°C.
The IPX4 rating provides protection against water splashing, making the pump suitable for appropriately protected outdoor installations.
It should not, however, be submerged or installed in a location subject to flooding.
Maximum Liquid Temperature
The current Malaysian specification gives a maximum liquid temperature of +40°C.
The pump is therefore primarily intended for:
- Cold groundwater
- Fresh water
- Domestic water
- Garden irrigation
- Agricultural irrigation
It is not designed as a dedicated hot-water circulation pump.
Pumping Medium
LEO specifies the AJDm range for clean water or other liquids with physical and chemical properties similar to water.
Recommended fluids include:
- Clean well water
- Groundwater
- Fresh water
- Irrigation water
- Domestic water
- Storage-tank water
Avoid pumping:
- Sewage
- Sludge
- Mud
- Fibrous liquids
- Heavy sand
- Highly abrasive liquids
- Liquids containing large suspended solids
If the well contains sand, suitable well development and filtration should be considered before operating the pump.
Recommended Applications
Deep-Well Water Supply
The AJDM110/4H is primarily intended for lifting clean groundwater from deep wells using an appropriate ejector arrangement.
Domestic Water Supply
The 1.5 HP motor provides higher pressure capability for supplying water to homes and small buildings from a suitable well.
Garden Irrigation
Suitable for sprinkler systems, garden hoses and irrigation lines where the required operating point is within the pump curve.
Agricultural Irrigation
The pump can be used for small-scale farm irrigation and clean-water transfer.
Water Tank Filling
Suitable for transferring well water into ground-level, elevated or storage tanks.
Pressure Boosting
The high-head capability makes it useful for selected pressure-boosting applications.
LEO explicitly lists well-water lifting, garden sprinkler irrigation and running-water pressure boosting among the AJDm series applications.
Key Advantages
The LEO AJDM110/4H provides:
- 1.1 kW / 1.5 HP motor
- 220 V single-phase operation
- Deep-well jet-pump configuration
- Self-priming design
- Up to approximately 40 m maximum suction
- Up to approximately 90 L/min published flow
- High-head performance
- Stainless-steel impeller
- AISI 304 stainless-steel shaft
- Anti-rust-treated cast-iron pump body
- Copper motor winding
- C&U bearing
- Built-in thermal protector
- Class F insulation
- IPX4 protection
- Carbon/ceramic mechanical seal
- Deep-well ejector system
- Suitable for domestic water supply
- Suitable for garden irrigation
- Suitable for small agricultural irrigation
- Suitable for water tank filling
- Suitable for pressure boosting.
AJDM55/4H vs AJDM75/4H vs AJDM110/4H
| Feature | AJDM55/4H | AJDM75/4H | AJDM110/4H |
|---|---|---|---|
| Motor | 0.55 kW / 0.75 HP | 0.75 kW / 1 HP | 1.1 kW / 1.5 HP |
| Pump Type | Deep-Well Jet | Deep-Well Jet | Deep-Well Jet |
| Impeller | Stainless Steel | Stainless Steel | Stainless Steel |
| Shaft | AISI 304 | AISI 304 | AISI 304 |
| Pump Body | Anti-Rust Cast Iron | Anti-Rust Cast Iron | Anti-Rust Cast Iron |
| Motor Winding | Copper | Copper | Copper |
| Max. Suction | Up to 40 m* | Up to 40 m* | Up to 40 m |
| Max. Flow | Lower | Medium | Up to 90 L/min* |
| Head Capability | Lower | Medium | Higher |
| Recommended Duty | Small | Small–Medium | Medium–Higher |
*Specifications vary by regional version and ejector configuration.
The AJDM110/4H is the highest-powered of these three models and is the preferred option when the installation requires higher pressure, greater water delivery or more demanding deep-well operation.
Installation Considerations
Deep-well jet pumps require more careful installation than conventional surface centrifugal pumps.
Before installation:
- Measure the static water level.
- Determine the dynamic water level.
- Select the appropriate ejector.
- Install the ejector at the recommended depth.
- Use appropriate pressure and suction/return pipe sizes.
- Make every pipe joint airtight.
- Install the appropriate foot valve/check valve.
- Minimize unnecessary bends.
- Verify that the well can continuously supply the required water.
- Prime the pump correctly.
- Never operate the pump without water.
- Provide proper electrical protection and earthing.
The 40 m maximum suction rating does not mean that every installation will deliver useful flow at 40 m. System friction, water level and required discharge pressure must all be considered.
Product Description
LEO AJDM110/4H Deep-Well Jet Pump 1.1kW / 1.5HP 220V is a high-performance self-priming jet pump designed for lifting clean water from deep wells and supplying water for domestic use, garden irrigation, small-scale agricultural irrigation, water tank filling and pressure boosting.
The pump combines a surface-mounted centrifugal pump with a deep-well ejector/venturi system and offers a published maximum suction of approximately 40 m. Current Malaysian specifications list up to 90 L/min flow and approximately 80–28 m head, while some other current listings quote up to 95 m maximum head depending on the specific regional specification.
The pump features a stainless-steel impeller, AISI 304 stainless-steel shaft and anti-rust-treated cast-iron pump body, while the 1.1 kW / 1.5 HP motor uses copper winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection.
With its deep-well ejector configuration and high-pressure capability, the AJDM110/4H is a suitable choice for deep-well water lifting, domestic water systems, garden irrigation, farm irrigation and clean-water pressure boosting.
SEO Product Title
LEO AJDM110/4H Deep Well Jet Pump 1.1kW 1.5HP 220V Self-Priming Water Pump for Garden & Irrigation
Short Product Description
LEO AJDM110/4H is a 1.1kW / 1.5HP 220V deep-well self-priming jet pump designed for lifting clean water from deep wells and supplying water for domestic use, garden irrigation, farm irrigation, water tank filling and pressure boosting. It features a stainless-steel impeller, AISI 304 stainless-steel shaft, anti-rust-treated cast-iron pump body, copper-wound motor, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection. With approximately 40 m maximum suction and published flow capability up to 90 L/min, the AJDM110/4H is suitable for demanding deep-well and clean-water pumping applications.
Inquiry - LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - AJDM 110/4H