B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - EKJ-602S



The LEO EKJ-602S is a 0.6 kW / 0.8 HP, 220 V single-phase self-priming garden jet pump designed for clean-water pumping, domestic water pressurisation, shallow-well water supply, garden irrigation and general water transfer.

It is a surface-mounted centrifugal pump with an integrated ejector/jet system, allowing it to self-prime and lift water from a source located below the pump. Current Malaysian listings specify 60 L/min maximum flow, 35 m maximum head and 8 m maximum suction, while some regional specifications list 50 L/min and 7–8 m suction.

The EKJ-602S is also associated with the older LEO LKJ-601S model designation.

Technical Specifications

Specification LEO EKJ-602S
Brand LEO
Series EKJ
Model EKJ-602S
Previous Model LKJ-601S
Pump Type Self-Priming Garden Jet Pump
Pump Construction Surface-Mounted Centrifugal Pump
Motor Power 0.6 kW / 0.8 HP
Voltage 220 V
Frequency 50 Hz
Phase Single Phase
Maximum Flow 60 L/min*
Maximum Head 35 m
Maximum Suction 8 m*
Inlet 1" / 25 mm
Outlet 1" / 25 mm
Impeller Closed Impeller
Shaft AISI 304 Stainless Steel
Pump Chamber Stainless Steel
Motor Winding Copper
Thermal Protection Built-In
Motor Protection IPX4
Maximum Liquid Temperature +35°C
Maximum Ambient Temperature +40°C
Installation Surface Mounted
Application Garden, Domestic Water Supply, Pressure Boosting, Shallow-Well Water

*Some regional LEO EKJ-602S specifications state 50 L/min maximum flow and 7 m suction, while current Malaysian listings specify 60 L/min and 8 m. The actual pump nameplate and manufacturer's curve supplied with the unit should be treated as the final specification.

Self-Priming Jet Pump Design

The EKJ-602S is designed as a self-priming centrifugal jet pump. It incorporates a jet/ejector arrangement into the pump system to assist in creating suction and maintaining water flow.

Unlike a conventional centrifugal pump that generally requires the suction line and pump chamber to be completely filled before operation, the self-priming arrangement allows the EKJ-602S to recover prime after the initial commissioning process, provided the suction system remains correctly installed and free from air leakage.

LEO's EKJ series is intended for water transfer, automatic water supply and increasing water pressure in water-supply systems.

0.6 kW / 0.8 HP Motor

The EKJ-602S uses a 600 W / 0.8 HP single-phase motor operating at 220 V, 50 Hz.

This power rating makes the pump suitable for relatively small domestic and garden systems.

Typical applications include:

  • Garden watering
  • Sprinkler systems
  • Shallow wells
  • Domestic water supply
  • Water tank transfer
  • Low-pressure water boosting
  • Greenhouse irrigation
  • Small irrigation systems

The 0.8 HP motor provides a practical balance between water delivery and electrical consumption for residential applications.

Maximum Flow – 60 L/min

Current Malaysian specifications list the EKJ-602S with a maximum flow rate of 60 L/min, equivalent to approximately 3.6 m³/h.

Some other regional specifications publish 50 L/min, so the precise maximum flow should be verified against the pump curve for your stock.

Maximum flow should not be interpreted as the flow available at maximum head.

The actual flow depends on:

  • Total dynamic head
  • Pipe length
  • Pipe diameter
  • Fittings
  • Elevation
  • Suction lift
  • Discharge pressure
  • Water-source conditions

For example, as discharge pressure and elevation increase, available flow will decrease.

Maximum Head – 35 m

The EKJ-602S has a maximum head of approximately 35 m.

A 35 m head corresponds to approximately 3.5 bar of static water head before accounting for friction and other system losses.

In an actual installation, the pressure available at the outlet will be lower because part of the pump's head is consumed by:

  • Pipe friction
  • Valves
  • Elbows
  • Filters
  • Check valves
  • Elevation
  • Hose resistance
  • Other fittings

Therefore, the 35 m rating should be considered the pump's maximum theoretical head at very low or zero flow, not the normal operating pressure at 60 L/min.

Maximum Suction – 8 m

The EKJ-602S is commonly specified with a maximum suction lift of approximately 8 m.

This makes it suitable for shallow wells and water sources below the pump, but it should not be treated as a true deep-well ejector system capable of lifting water from several tens of metres.

For reliable operation, the practical suction lift should be kept within the manufacturer's stated limit and preferably minimized.

Actual suction performance depends on:

  • Water temperature
  • Atmospheric pressure
  • Suction-pipe diameter
  • Suction-pipe length
  • Pipe friction
  • Foot valve
  • Pipe fittings
  • Air leakage
  • Water level while pumping

A longer or undersized suction line can substantially reduce performance.

1" × 1" Water Connections

The EKJ-602S uses 1" / 25 mm inlet and outlet connections.

This makes it compatible with many standard domestic and garden water-piping systems.

The 1" connection size is suitable for:

  • Garden hoses and piping
  • Domestic water lines
  • Small irrigation systems
  • Water tanks
  • Shallow-well systems

For suction applications, maintaining an airtight suction line is especially important.

Closed Impeller

The EKJ-602S uses a closed impeller. Current product information identifies it as a self-priming centrifugal pump with a closed impeller.

The closed-impeller design is appropriate for clean-water applications where the pumped liquid contains little or no abrasive material.

Suitable water sources include:

  • Clean groundwater
  • Domestic water
  • Storage tanks
  • Rainwater after appropriate filtration
  • Garden water
  • Irrigation water

It is not intended for sewage, sludge or heavily contaminated water.

Stainless-Steel Pump Chamber

Regional product documentation describes the EKJ-602S as having a stainless-steel working/pump chamber.

The stainless-steel hydraulic chamber provides good corrosion resistance for clean-water applications and is particularly useful for:

  • Domestic water
  • Groundwater
  • Garden irrigation
  • Water storage systems

This construction should not be confused with the entire pump being manufactured from stainless steel; the motor and other external components use different materials.

AISI 304 Stainless-Steel Shaft

The pump shaft is manufactured from AISI 304 stainless steel.

This provides:

  • Corrosion resistance
  • Good mechanical strength
  • Durable rotating operation
  • Improved suitability for clean-water pumping

The AISI 304 shaft is an important feature for a pump intended for repeated domestic and garden use.

Copper Motor Winding

The EKJ-602S motor uses copper winding.

Copper provides good electrical conductivity and contributes to efficient motor operation.

The motor is designed for normal domestic and garden pumping duties and includes integrated thermal protection for the single-phase motor.

Built-In Thermal Protector

The single-phase motor incorporates a built-in thermal protector.

This helps protect the motor from overheating under abnormal operating conditions.

External electrical protection should still be provided according to the installation requirements, including suitable:

  • Circuit breaker
  • Earthing
  • Cable sizing
  • Isolation switch
  • Electrical connections

IPX4 Motor Protection

The motor is specified with IPX4 protection.

This provides protection against water splashing from different directions.

The pump should still be installed in a dry, ventilated location and protected from flooding or direct immersion.

Temperature Ratings

The EKJ-602S has a published maximum liquid temperature of +35°C.

A maximum ambient temperature of approximately +40°C is also specified in regional product information.

It is therefore intended primarily for:

  • Cold water
  • Groundwater
  • Domestic water
  • Garden irrigation
  • Tank water

It is not designed as a dedicated hot-water circulation pump.

Suitable Pumping Medium

The EKJ-602S is intended for clean water without sand, mud, abrasive particles, fibres or other significant contaminants.

Recommended applications include:

  • Clean well water
  • Domestic water
  • Rainwater after filtration
  • Garden water
  • Irrigation water
  • Storage-tank water

Do not use the pump for:

  • Sewage
  • Sludge
  • Mud
  • Fibrous wastewater
  • Heavy sand
  • Abrasive liquids
  • Large suspended solids

If the water source contains sand, an appropriate filtration system should be installed upstream of the pump.

Garden Irrigation

The EKJ-602S is particularly suitable for garden irrigation.

The 0.8 HP motor and 35 m maximum head provide useful pressure for:

  • Garden sprinklers
  • Watering hoses
  • Small irrigation networks
  • Greenhouses
  • Vegetable gardens
  • Landscape irrigation

The actual number of sprinklers that can operate simultaneously depends on their required flow and pressure.

Domestic Water Pressurisation

The EKJ-602S can be used for domestic water pressure boosting where the required pressure and flow are within its operating curve.

Potential applications include:

  • Boosting water from storage tanks
  • Supplying upper floors
  • Improving low-pressure water systems
  • Supplying outdoor taps
  • Supporting small domestic water systems

It can also be paired with appropriate pressure-control equipment for automatic water supply systems.

Shallow-Well Water Supply

With a maximum suction specification of approximately 8 m, the EKJ-602S can be used for shallow wells where the water level is within its practical suction capability.

The pump should be installed as close to the water source as practical.

A proper foot valve is recommended for suction installations to help maintain prime and prevent water from draining back into the well.

Water Tank Transfer

The EKJ-602S can be used to transfer clean water between tanks where the total head and required flow are within the pump's performance range.

Typical examples include:

  • Ground tank to elevated tank
  • Rainwater tank to irrigation tank
  • Storage tank to garden supply
  • Water reservoir to domestic storage

EKJ-602S vs EKJ-602P

The EKJ-602S and EKJ-602P are both compact 0.6 kW / 0.8 HP LEO garden jet pumps, but they are different model configurations.

Feature EKJ-602S EKJ-602P
Motor 0.6 kW / 0.8 HP 0.6 kW / 0.8 HP
Voltage 220 V 220 V
Max Flow 60 L/min* 50–60 L/min*
Max Head 35 m 35 m
Max Suction 8 m* 7–8 m*
Inlet/Outlet 1" × 1" 1" × 1"
Pump Type Self-Priming Jet Pump Self-Priming Jet Pump
Shaft AISI 304 SS AISI 304 SS
Primary Use Garden / Domestic Garden / Domestic

*Specifications vary between regional listings.

The EKJ-602S is the appropriate model to list separately from the EKJ-602P rather than treating the two model numbers as interchangeable.

EKJ-602S vs AJDM Deep-Well Pumps

It is also important to distinguish the EKJ-602S from LEO's AJDM deep-well jet pumps.

Feature EKJ-602S AJDM Series
Pump Type Surface Self-Priming Jet Pump Deep-Well Jet Pump
Motor 0.6 kW / 0.8 HP Various
Max Head 35 m Model dependent
Max Suction Approx. 8 m Much deeper with ejector
Deep-Well Ejector No external deep-well ejector Yes
Installation Surface only Surface pump + well ejector
Best Application Garden / shallow well Deep-well water lifting
Connection 1" × 1" Model dependent

Therefore, despite some retail descriptions using the phrase “deep well jet pump,” the EKJ-602S is technically much more appropriate for shallow-well and surface-water applications because its specified suction lift is approximately 8 m.

Key Advantages

The LEO EKJ-602S provides:

  1. 0.6 kW / 0.8 HP motor
  2. 220 V / 50 Hz single-phase operation
  3. Self-priming jet-pump design
  4. 60 L/min maximum published flow
  5. 35 m maximum head
  6. 8 m maximum published suction
  7. 1" × 1" water connections
  8. Closed impeller
  9. AISI 304 stainless-steel shaft
  10. Stainless-steel pump chamber
  11. Copper motor winding
  12. Built-in thermal protection
  13. IPX4 motor protection
  14. Maximum water temperature +35°C
  15. Compact surface-mounted construction
  16. Suitable for garden irrigation
  17. Suitable for domestic water pressurisation
  18. Suitable for shallow wells
  19. Suitable for water tank transfer
  20. Suitable for small irrigation systems.

Installation Recommendations

For reliable EKJ-602S operation:

  • Install the pump on a firm, level surface.
  • Keep the pump as close as practical to the water source.
  • Keep the suction lift within the specified limit.
  • Use an appropriately sized suction pipe.
  • Ensure all suction connections are completely airtight.
  • Install a suitable foot valve/check valve.
  • Minimize unnecessary elbows and restrictions.
  • Fill/prime the pump correctly before the first operation.
  • Do not operate the pump dry.
  • Ensure the water source can provide sufficient flow.
  • Provide suitable electrical protection and earthing.
  • Protect the motor from flooding and excessive weather exposure.

For suction installations, air leakage is one of the most common causes of poor self-priming performance.

Product Description

LEO EKJ-602S 0.6kW / 0.8HP 220V Self-Priming Garden Jet Pump is a compact surface-mounted centrifugal pump designed for garden irrigation, domestic water pressurisation, shallow-well water supply and clean-water transfer. The pump operates on 220 V single-phase power and provides a maximum head of 35 m, with current Malaysian specifications listing up to 60 L/min maximum flow and 8 m maximum suction.

The EKJ-602S features a closed impeller, AISI 304 stainless-steel shaft, stainless-steel working chamber, copper-wound motor, built-in thermal protection and IPX4 motor protection. Its self-priming jet design makes it suitable for domestic and garden water systems where the water source is within its practical suction limit.

With 1" × 1" water connections, 35 m maximum head and 0.8 HP motor power, the LEO EKJ-602S is a practical choice for home water supply, garden watering, shallow-well pumping, tank transfer and small irrigation applications.

SEO Product Title

LEO EKJ-602S 0.6kW 0.8HP 220V Self-Priming Garden Jet Pump 35m Head 60L/min

Short Product Description

LEO EKJ-602S is a 0.6kW / 0.8HP 220V self-priming garden jet pump designed for domestic water pressurisation, garden irrigation, shallow-well pumping and clean-water transfer. It features 60 L/min maximum flow, 35 m maximum head, approximately 8 m maximum suction, 1" × 1" connections, closed impeller, AISI 304 stainless-steel shaft, stainless-steel pump chamber, copper motor winding, built-in thermal protection and IPX4 protection. Its compact surface-mounted design makes it suitable for household, garden, tank and small irrigation systems.



 Inquiry - LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - EKJ-602S