B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - 4XCM-120SA



The LEO 4XCM-120SA is a 1.1 kW / 1.5 HP self-priming multistage centrifugal jet pump designed for domestic water supply, garden irrigation, water pressure boosting, shallow/deep-well applications with suitable suction arrangements, and general clean-water transfer. Current Malaysian product listings identify the 4XCM-120SA as a 1.1 kW, 1.5 HP self-priming garden/deep-well jet pump.

The model belongs to LEO's XCM multistage pump family. The “4” denotes the four-stage configuration, while the “SA” version is the stainless-steel/self-priming configuration used for this range. LEO's catalogue listings also distinguish the 4XCM-120S and 4XCM-120SA as separate variants.

Technical Specifications

Specification LEO 4XCM-120SA
Brand LEO
Model 4XCM-120SA
Pump Type Self-Priming Multistage Jet Pump
Pump Series XCM
Hydraulic Stages 4 Stage
Motor Power 1.1 kW / 1.5 HP
Voltage 220 V
Phase Single Phase
Frequency 50 Hz
Maximum Head Approx. 50 m*
Maximum Flow Approx. 4–5 m³/h*
Maximum Suction Approx. 8 m*
Pump Body Stainless Steel
Shaft Stainless Steel
Impeller Multistage
Motor Winding Copper
Motor Protection Thermal Protection
Insulation Class F
Protection Class IPX4
Installation Surface Mounted
Priming Self-Priming
Suitable Liquid Clean Water
Application Domestic, Garden, Irrigation, Well Water, Pressure Boosting

*Exact flow/head values should be confirmed against the nameplate and pump performance curve supplied with the specific production version. Malaysian listings confirm the 1.1 kW / 1.5 HP rating, but published hydraulic specifications can differ between market versions.

1.1 kW / 1.5 HP Motor

The 4XCM-120SA is equipped with a 1.1 kW / 1.5 HP single-phase motor, giving it substantially more pumping capacity than smaller EKJ garden pumps.

This power rating is suitable for applications requiring:

  • Higher water pressure
  • Longer discharge pipe runs
  • Elevated water tanks
  • Garden sprinkler systems
  • Domestic pressure boosting
  • Small irrigation networks
  • Water transfer over greater elevations

The 1.5 HP motor makes the 4XCM-120SA suitable for more demanding water-supply applications while retaining a relatively compact surface-pump configuration.

Four-Stage Multistage Design

The pump uses a four-stage centrifugal hydraulic configuration.

In a multistage pump, several impellers operate in series. The pressure generated by each stage is accumulated, allowing the pump to achieve considerably higher head than a conventional single-stage garden pump.

The four-stage arrangement is particularly useful for:

  • High-pressure domestic water supply
  • Garden sprinklers
  • Irrigation
  • Water tank boosting
  • Long-distance water transfer
  • Elevated tank filling
  • Pressure boosting

This makes the 4XCM-120SA appropriate when the application requires higher pressure rather than simply high-volume water transfer.

Self-Priming Operation

The 4XCM-120SA is a self-priming pump, which allows it to draw water from a suitable source below the pump after the pump and suction system have been correctly primed.

Typical applications include:

  • Shallow wells
  • Storage tanks
  • Ground tanks
  • Rainwater tanks
  • Garden reservoirs
  • Domestic water systems
  • Irrigation sources

The suction pipe must remain airtight. Air entering the suction line can prevent the pump from establishing proper suction.

Maximum Head

The 4XCM-120SA is designed as a high-head multistage pump, with maximum head commonly in the approximate 50 m class, depending on the exact hydraulic specification.

A 50 m water head corresponds to approximately 5 bar of static pressure.

However, maximum head occurs at very low flow. The pump should therefore be selected according to the actual required operating point rather than the maximum head alone.

For example:

Higher flow requirement → lower available head

Lower flow requirement → higher available head

Pipe friction, elevation and fittings must be included when calculating total dynamic head.

Flow Capacity

The 4XCM-120SA is designed to provide useful flow while maintaining relatively high discharge pressure.

The practical flow rate depends on:

  • Discharge head
  • Suction conditions
  • Pipe diameter
  • Pipe length
  • Pipe friction
  • Valves
  • Filters
  • Sprinkler requirements
  • Elevation

For accurate system design, use the manufacturer's performance curve to determine the flow available at the required head.

Stainless-Steel Construction

The 4XCM-120SA is part of LEO's stainless-steel XCM pump range.

The stainless-steel construction provides:

  • Good corrosion resistance
  • Durable hydraulic components
  • Better resistance to humid environments
  • Clean appearance
  • Suitability for domestic water applications
  • Good outdoor durability

This makes the pump appropriate for applications where the pump may be exposed to moisture or where corrosion resistance is important.

Stainless-Steel Shaft

The stainless-steel shaft provides good corrosion resistance and mechanical strength.

It is suitable for normal clean-water applications including:

  • Domestic water
  • Groundwater
  • Irrigation
  • Garden water
  • Water tanks
  • Rainwater systems

Multistage Impeller System

The multistage impeller arrangement provides the pressure required for high-head applications.

Each hydraulic stage contributes additional pressure, allowing the pump to achieve higher head while maintaining a relatively compact pump body.

This is one of the primary reasons the 4XCM-120SA is suitable for:

  • Sprinkler irrigation
  • Multi-storey water supply
  • Long pipe runs
  • Water pressure boosting
  • Elevated tanks

Clean-Water Applications

The 4XCM-120SA is intended for clean water and non-aggressive liquids.

Recommended applications include:

  • Fresh water
  • Filtered groundwater
  • Domestic water
  • Irrigation water
  • Rainwater
  • Storage-tank water

It should not be used for heavily contaminated or abrasive liquids such as:

  • Sewage
  • Sludge
  • Mud
  • Sand-heavy water
  • Abrasive slurry
  • Water containing large solids
  • Fibrous wastewater

If the water source contains sand, install an appropriate filter or separator upstream of the pump.

Garden Irrigation

The 4XCM-120SA is well suited to garden and landscape irrigation where higher pressure is required.

It can be used for:

  • Lawn sprinklers
  • Garden sprinklers
  • Landscape irrigation
  • Greenhouse irrigation
  • Vegetable gardens
  • Small agricultural irrigation
  • Hose systems

The four-stage design is especially useful when sprinklers need higher pressure to achieve their specified spray pattern.

Domestic Water Pressure Boosting

The 1.5 HP motor and multistage configuration make the 4XCM-120SA suitable for selected domestic pressure-boosting systems.

Typical installations include:

Storage tank → pump → house

Ground tank → pump → upper-floor supply

Rainwater tank → pump → irrigation

Well → pump → domestic water system

For automatic operation, a suitable pressure controller, pressure switch or pressure tank can be installed.

Water Tank Transfer

The pump can transfer clean water between tanks where the total head remains within the pump's operating range.

Typical applications include:

  • Ground tank to elevated tank
  • Underground tank to building
  • Rainwater tank to garden
  • Reservoir to irrigation system
  • Storage tank to domestic supply

For tank-to-tank transfer, the required flow and elevation should be calculated before selecting the pump.

Well-Water Applications

The product is marketed as a deep-well/garden jet pump in Malaysian listings.

However, the actual well configuration is important.

A surface-mounted self-priming pump cannot directly lift water from an arbitrarily deep water level. Where the static water level is beyond the practical suction capability of a conventional surface pump, an appropriate deep-well ejector arrangement or submersible pump should be used.

For well installations, consider:

  • Static water level
  • Dynamic water level
  • Suction lift
  • Pipe diameter
  • Suction pipe length
  • Foot valve
  • Well recovery rate
  • Total dynamic head

Maximum Suction

The XCM pump configuration is intended for surface installation with suction capability dependent on the hydraulic arrangement.

For practical installation, keep the pump as close to the water source as possible.

A long or undersized suction pipe can significantly reduce performance.

Always ensure:

  • No air leaks
  • Correct suction pipe size
  • Proper foot valve
  • Correct priming
  • Adequate water supply

Copper Motor Winding

The motor uses copper winding for good electrical conductivity and reliable operation.

The motor should be supplied through correctly sized electrical cables and protected by an appropriate circuit breaker and overload protection system.

Thermal Protection

Thermal protection helps protect the motor from excessive temperature resulting from abnormal operating conditions.

Possible causes include:

  • Motor overload
  • Restricted ventilation
  • Excessive ambient temperature
  • Mechanical resistance
  • Incorrect electrical supply
  • Prolonged abnormal operation

Thermal protection does not replace proper electrical installation and overload protection.

Class F Insulation

The motor is specified with Class F insulation, providing good thermal resistance for continuous-duty motor operation when the pump is correctly selected and installed.

IPX4 Protection

The motor is designed with IPX4-level protection against water splashing.

For outdoor installation, the pump should nevertheless be protected against:

  • Flooding
  • Standing water
  • Direct high-pressure water jets
  • Prolonged heavy rain exposure
  • Submersion

Install the pump in a dry and well-ventilated location.

Typical Applications

The LEO 4XCM-120SA can be used for:

Domestic Water Supply
Supplying clean water to homes and small buildings.

Garden Irrigation
Operating sprinklers, hoses and landscape irrigation systems.

Water Pressure Boosting
Increasing pressure from storage tanks or other low-pressure sources.

Shallow-Well Pumping
Drawing water from suitable shallow wells when suction requirements are within the pump's capability.

Deep-Well Systems
Suitable where combined with an appropriate ejector/deep-well arrangement.

Water Tank Filling
Moving water from ground-level tanks to elevated storage tanks.

Rainwater Systems
Using filtered rainwater for irrigation and other suitable non-potable applications.

4XCM-120SA vs 5XCM-120SA

Feature 4XCM-120SA 5XCM-120SA
Hydraulic Stages 4 5
Motor Power 1.1 kW / 1.5 HP 1.3 kW / 1.75 HP
Main Characteristic High-pressure Higher-pressure
Construction Stainless Steel Stainless Steel
Pump Type Self-Priming Multistage Self-Priming Multistage
Main Applications Domestic / Garden / Irrigation Higher-demand domestic / irrigation
Selection Moderate pressure demand Higher pressure demand

Current Malaysian listings identify the 4XCM-120SA at 1.1 kW / 1.5 HP and the 5XCM-120SA at 1.3 kW / 1.75 HP, making the 5XCM-120SA the higher-powered model in this pair.

Key Advantages

The LEO 4XCM-120SA offers:

  1. 1.1 kW / 1.5 HP motor
  2. 220 V single-phase operation
  3. Four-stage multistage hydraulic design
  4. Self-priming operation
  5. Stainless-steel construction
  6. Stainless-steel shaft
  7. High-pressure pumping capability
  8. Copper motor winding
  9. Class F insulation
  10. IPX4 protection
  11. Thermal motor protection
  12. Suitable for clean water
  13. Suitable for domestic water supply
  14. Suitable for garden irrigation
  15. Suitable for sprinkler systems
  16. Suitable for water tank transfer
  17. Suitable for pressure boosting
  18. Suitable for shallow-well applications
  19. Suitable for appropriate deep-well ejector systems
  20. Compact surface-mounted design.

Installation Recommendations

For reliable operation:

  • Install the pump on a firm, level foundation.
  • Position the pump as close to the water source as practical.
  • Use correctly sized suction and discharge piping.
  • Keep the suction line short and straight.
  • Minimize elbows and restrictions.
  • Install a suitable foot valve/check valve.
  • Ensure all suction connections are airtight.
  • Prime the pump correctly before operation.
  • Never operate the pump dry.
  • Ensure sufficient water supply.
  • Install suitable electrical protection.
  • Provide proper earthing.
  • Maintain adequate motor ventilation.
  • Protect the pump from flooding.
  • Use filtration if the water contains sand or suspended particles.

Product Description

LEO 4XCM-120SA 1.1kW 1.5HP Stainless Steel Self-Priming Multistage Jet Pump is a high-pressure water pump designed for domestic water supply, garden irrigation, water tank transfer, pressure boosting and suitable well-water applications. Its four-stage multistage hydraulic design provides higher pressure capability than conventional single-stage garden pumps, making it suitable for sprinkler systems, elevated water supply and applications requiring increased discharge pressure.

The pump features stainless-steel construction, stainless-steel shaft, copper motor winding, thermal protection, Class F insulation and IPX4 motor protection. Its self-priming configuration allows it to be used with suitable surface-water and well-water systems when the suction arrangement is correctly designed.

The LEO 4XCM-120SA is a practical choice for residential, garden, irrigation and light commercial clean-water applications where a 1.5 HP stainless-steel high-pressure multistage pump is required. The model is currently listed in Malaysia as a 1.1 kW / 1.5 HP self-priming garden/deep-well pump.

SEO Product Title

LEO 4XCM-120SA 1.1kW 1.5HP 220V Stainless Steel Self-Priming Multistage Jet Pump

Short Product Description

LEO 4XCM-120SA is a 1.1kW / 1.5HP 220V stainless-steel self-priming multistage jet pump designed for domestic water supply, garden irrigation, sprinkler systems, water tank transfer, pressure boosting and suitable well-water applications. Its four-stage hydraulic design provides high-pressure water delivery, while stainless-steel construction, stainless-steel shaft, copper motor winding, thermal protection and Class F insulation provide reliable performance for clean-water applications.



 Inquiry - LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - 4XCM-120SA