The LEO LEZ 125-100-160/176-2 is a heavy-duty end-suction centrifugal water pump designed for high-volume water transfer and industrial, commercial, irrigation, building-services and general water-supply applications. The model is listed within LEO's industrial centrifugal-pump range in Malaysia.
The LEZ series is intended for applications where a conventional domestic centrifugal pump is insufficient and a more robust, higher-capacity pump configuration is required. Its end-suction arrangement provides a practical layout for installation in water-supply, circulation and transfer systems.
Product Specifications
| Specification | LEO LEZ 125-100-160/176-2 |
|---|---|
| Brand | LEO |
| Model | LEZ 125-100-160/176-2 |
| Pump Type | End-Suction Centrifugal Pump |
| Series | LEZ |
| Pump Configuration | Horizontal End-Suction |
| Impeller Type | Closed Centrifugal Impeller |
| Suction Connection | DN125 |
| Discharge Connection | DN100 |
| Nominal Impeller Diameter | 160 mm |
| Maximum Impeller Diameter | 176 mm |
| Drive Configuration | 2-Pole Motor |
| Motor Speed | Approx. 2900 rpm at 50 Hz |
| Application | Clean-Water Transfer / Circulation |
| Installation | Horizontal |
| Liquid | Clean Water / Similar Liquids |
| Pump Duty | Continuous Industrial / Commercial Applications |
| Construction | Heavy-Duty Industrial Construction |
| Mounting | Base Mounted |
| Motor | 3-Phase Industrial Motor |
| Suitable Industries | Industrial, Commercial, Irrigation, Building Services |
The model number itself provides useful dimensional information: 125-100 corresponds to the nominal suction/discharge connection sizes, while 160/176 identifies the impeller diameter range. The final “-2” denotes the 2-pole/high-speed configuration.
LEO's industrial pump range includes dedicated LEP end-suction centrifugal pumps, while the LEZ 125-100-160/176-2 is specifically listed by Malaysian LEO distributors as an industrial end-suction centrifugal model.
End-Suction Centrifugal Design
The LEZ 125-100-160/176-2 uses a conventional end-suction centrifugal configuration.
Water enters axially through the suction side of the pump and is accelerated by the rotating impeller before being discharged through the outlet.
This arrangement provides several advantages:
- Simple hydraulic layout
- High-volume water handling
- Easy connection to standard pipework
- Convenient maintenance access
- Suitable for continuous-duty operation
- Suitable for industrial water systems
- Compatible with motor/base-frame installations
The design is particularly appropriate for systems requiring substantial water movement rather than extremely high pressure.
DN125 Suction / DN100 Discharge
The 125-100 designation indicates the nominal connection arrangement:
- DN125 suction
- DN100 discharge
The relatively large suction and discharge connections allow the pump to handle substantially greater water volume than smaller domestic centrifugal pumps.
Correct pipe sizing is important to minimize hydraulic losses.
The suction line should generally be:
- Short
- Straight
- Properly supported
- Appropriately sized
- Free from unnecessary restrictions
Avoid reducing the suction pipe immediately before the pump unless the hydraulic design specifically requires it.
160 / 176 mm Impeller
The 160/176 designation refers to the pump's impeller diameter configuration.
The pump can therefore be selected or configured around the applicable impeller diameter to achieve the required hydraulic duty.
In centrifugal pump selection, impeller diameter has a direct influence on:
- Head
- Flow
- Pump power
- Efficiency
- Operating point
A larger impeller generally provides greater head at a given speed, while an appropriately trimmed impeller can be used where lower head is required.
For a specific installation, the correct impeller diameter should always be selected using the manufacturer's performance curve.
2-Pole High-Speed Configuration
The final “-2” in the model designation indicates a 2-pole motor configuration.
At 50 Hz, a typical 2-pole induction motor operates at approximately 2900 rpm under load, depending on motor slip.
The high rotational speed allows the pump to achieve substantial hydraulic performance from a relatively compact impeller.
The 2-pole configuration is suitable for applications where:
- High flow is required
- Compact pump dimensions are preferred
- Higher rotational speed is appropriate
- Industrial continuous operation is required
High-Volume Water Transfer
The LEZ 125-100-160/176-2 is designed for high-capacity water movement.
Typical applications include:
- Industrial water transfer
- Building water circulation
- Irrigation systems
- Cooling-water circulation
- General water supply
- Water treatment systems
- Factory process-water circulation
- Commercial water systems
- Tank-to-tank transfer
- Municipal water applications
The actual flow rate and head must be selected according to the system curve and manufacturer's pump performance curve.
Industrial Water Supply
The pump is suitable for industrial water-supply systems where reliable continuous water movement is required.
Possible applications include:
- Factory water supply
- Production-line water circulation
- Industrial cooling systems
- Process-water transfer
- Storage tank transfer
- General plant water systems
For industrial installations, the pump should be correctly matched to the required duty point to prevent operation outside the recommended operating range.
Irrigation Applications
The high-capacity configuration also makes the LEZ suitable for selected agricultural and commercial irrigation systems.
Potential applications include:
- Farm irrigation
- Plantation irrigation
- Large sprinkler systems
- Agricultural water transfer
- Reservoir distribution
- Water-storage systems
- Irrigation pumping stations
The large DN125 suction and DN100 discharge connections are particularly useful in larger irrigation installations where high water volume is required.
Building Services
The pump can be used in commercial and building-service water systems where the hydraulic requirements are within its performance range.
Possible uses include:
- Commercial water circulation
- Water transfer
- Cooling-water systems
- HVAC circulation
- Tank filling
- General building water systems
LEO's broader centrifugal-pump portfolio includes pumps for industrial and building water applications, including circulation and pressurization systems.
Suitable Liquids
The pump is primarily intended for clean water and liquids with physical and chemical characteristics similar to water.
Suitable fluids may include:
- Fresh water
- Treated water
- Cooling water
- Irrigation water
- Industrial service water
- Filtered process water
The liquid should not contain excessive abrasive particles or fibrous materials unless the specific pump configuration is approved for such service.
For chemically aggressive liquids, the seal and wetted-component materials must be verified before use.
Continuous-Duty Operation
The industrial construction of this class of pump makes it suitable for continuous or extended operating periods when correctly installed.
For continuous-duty systems, attention should be given to:
- Correct pump sizing
- Motor protection
- Shaft alignment
- Bearing condition
- Mechanical seal condition
- Adequate suction conditions
- Correct operating temperature
- Proper foundation
- Correct coupling alignment
Operating continuously far outside the recommended performance range can cause premature wear and increased energy consumption.
Mechanical Seal
The mechanical seal prevents water from escaping along the rotating shaft.
Correct seal selection depends on:
- Liquid temperature
- Liquid chemistry
- Operating pressure
- Pump speed
- Water quality
For clean-water service, a standard mechanical-seal arrangement is normally suitable, subject to the manufacturer's specified materials.
Never operate the pump dry, as dry running can rapidly damage the mechanical seal.
Motor and Drive
The LEZ 125-100-160/176-2 is intended for connection to an industrial motor/drive assembly.
For a typical 50 Hz installation, the 2-pole configuration operates at approximately 2900 rpm.
A correctly selected three-phase motor should include appropriate:
- Overload protection
- Short-circuit protection
- Phase-loss protection
- Earthing
- Isolation
- Correct cable sizing
Motor power must be selected according to the actual pump duty point rather than based solely on the maximum possible flow.
Pump Performance Selection
The most important factors when selecting the LEZ 125-100-160/176-2 are:
Required Flow (Q)
The volume of water required, normally expressed in m³/h.
Total Dynamic Head (H)
The total pressure requirement including static elevation, pipe friction and required discharge pressure.
Operating Speed
The 2-pole configuration determines the approximate operating speed.
Impeller Diameter
The applicable impeller diameter determines the pump's hydraulic performance.
Liquid Characteristics
Temperature, viscosity, solids content and chemical properties affect pump selection.
System Head Calculation
Before installation, calculate:
Total Dynamic Head = Static Head + Pipe Friction + Fitting Losses + Required Outlet Pressure
For example, a system transferring water to an elevated tank must account for:
- Vertical height
- Horizontal pipe length
- Elbows
- Valves
- Check valves
- Filters
- Pipe diameter
- Tank inlet losses
Selecting the pump only according to pipe size is not sufficient.
NPSH and Suction Conditions
For a large end-suction centrifugal pump, adequate Net Positive Suction Head Available (NPSHA) is essential.
Poor suction conditions can cause cavitation.
Symptoms of cavitation may include:
- Unusual noise
- Vibration
- Reduced flow
- Reduced pressure
- Impeller damage
- Premature bearing/seal failure
To improve suction conditions:
- Keep suction piping short.
- Avoid unnecessary elbows.
- Use an appropriately sized suction pipe.
- Minimize suction-side restrictions.
- Ensure adequate water level.
- Avoid excessive suction lift.
- Keep the suction line free from air leaks.
Base-Mounted Installation
Unlike compact domestic close-coupled pumps, industrial end-suction pumps are commonly installed on a rigid base/foundation.
A proper installation should provide:
- Level foundation
- Adequate structural support
- Correct shaft alignment
- Proper pipe support
- Flexible coupling where applicable
- Suitable guards around rotating components
Pipework should never be allowed to place excessive mechanical load on the pump casing.
Maintenance
Routine maintenance should include inspection of:
- Mechanical seal
- Bearings
- Coupling
- Motor
- Pump shaft
- Impeller
- Casing
- Foundation bolts
- Pipe connections
Monitor:
- Pump vibration
- Motor temperature
- Bearing noise
- Discharge pressure
- Flow rate
- Motor current
A change in normal operating conditions can indicate wear, blockage, cavitation or system changes.
Typical Applications
The LEO LEZ 125-100-160/176-2 is suitable for:
- Industrial water transfer
- Commercial water supply
- Agricultural irrigation
- Large sprinkler systems
- Factory cooling-water circulation
- HVAC water circulation
- Water treatment systems
- Tank-to-tank water transfer
- Industrial process-water circulation
- Building-service water systems
- Reservoir pumping
- General clean-water pumping
- Water conservation projects
- Industrial utility-water systems
Key Advantages
The LEO LEZ 125-100-160/176-2 offers:
- Heavy-duty end-suction centrifugal design
- Large DN125 suction connection
- DN100 discharge connection
- 160/176 mm impeller configuration
- 2-pole high-speed configuration
- Suitable for high-volume water transfer
- Suitable for industrial applications
- Suitable for irrigation
- Suitable for commercial water systems
- Suitable for water circulation
- Suitable for tank transfer
- Suitable for building services
- Base-mounted industrial configuration
- Serviceable centrifugal-pump construction
- Suitable for clean water and similar liquids
Important Specification Note
For this particular LEZ 125-100-160/176-2, publicly indexed sources confirm the model and its classification as an LEO end-suction centrifugal pump, but I could not verify a reliable manufacturer-published performance table for this exact model from the available sources. The model is listed by Malaysian LEO distributors under industrial centrifugal pumps.
Therefore, values such as exact motor kW, rated flow, rated head, efficiency, impeller trim and NPSHr should be taken from the pump nameplate or LEO's specific performance curve, rather than inserting an unverified figure into the product listing.
Product Description
LEO LEZ 125-100-160/176-2 End Suction Centrifugal Pump is a heavy-duty industrial water pump designed for high-volume clean-water transfer, industrial water supply, irrigation, commercial water systems, cooling-water circulation, building services and general water-transfer applications. The pump features a conventional end-suction centrifugal configuration, large DN125 suction and DN100 discharge connections, a 160/176 mm impeller configuration and a 2-pole high-speed drive arrangement.
Its large hydraulic connections and industrial configuration make it suitable for demanding applications requiring reliable and continuous water movement. The pump can be integrated into industrial pipework, irrigation networks, water-treatment systems, commercial water supplies, tank-transfer systems and circulation systems.
For accurate pump selection, the required flow rate, total dynamic head, impeller diameter, motor power and NPSH requirements should be checked against the manufacturer's performance curve for the specific LEZ 125-100-160/176-2 configuration.
SEO Product Title
LEO LEZ 125-100-160/176-2 End Suction Centrifugal Water Pump – Industrial Heavy Duty
Short Product Description
LEO LEZ 125-100-160/176-2 is a heavy-duty end-suction centrifugal pump designed for industrial, commercial, irrigation, water-transfer and circulation applications. Featuring DN125 suction, DN100 discharge, 160/176 mm impeller configuration and a 2-pole high-speed drive, this pump is designed for high-volume clean-water handling and continuous-duty applications. Suitable for industrial water supply, agricultural irrigation, cooling-water circulation, building services, tank transfer and general water systems.
Inquiry - LEO END SUCTION CENTRIFUGAL PUMPS - LEZ 125-100-160/176-2