B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO AUTOMATIC SELF-PRIMING PUMP - APSM 75AT



The LEO APSM 75AT is an automatic self-priming peripheral water pump equipped with a 0.75 kW / 1.0 HP single-phase motor. It is designed for domestic water supply, garden irrigation, automatic sprinkler systems, water transfer and other clean-water applications where automatic pump operation and relatively high pressure are required. LEO specifies the APSm-AT series for clean-water transfer, small domestic water supply, automatic sprinkler systems and small air-conditioning/support equipment.

The APSM 75AT provides a published 5–45 L/min flow range, 5–50 m head range, and 8 m maximum suction. It uses 1" × 1" connections and a 220 V single-phase supply. Malaysian supplier specifications list the motor at 0.75 kW / 1.0 HP.

Technical Specifications

Specification LEO APSM 75AT
Brand LEO
Model APSM 75AT
Pump Type Automatic Self-Priming Peripheral Pump
Motor Power 0.75 kW / 1.0 HP
Voltage 220 V
Phase Single Phase
Frequency 50 Hz
Flow Range 5–45 L/min
Maximum Flow Approx. 2.7 m³/h
Head Range 50–5 m
Maximum Head 50 m
Rated Flow 28 L/min
Rated Head 20 m
Maximum Suction 8 m
Inlet / Outlet 1" × 1"
Pump Type Peripheral / Self-Priming
Pump Body Stainless Steel
Impeller Stainless Steel
Shaft AISI 304 Stainless Steel
Motor Winding Copper
Insulation Class F
Protection Class IPX4
Thermal Protection Built-In
Automatic Function Yes
No-Water Protection Yes
Automatic Water Detection Yes
Start Delay 2 seconds
Operating Status Power Up / Running / No Water
Dimensions 300 × 300 × 250 mm
Weight 10.2 kg

The manufacturer's technical table for the APSm-AT range lists the APSm75AT at 5–45 L/min, 45–5 m operating head, 28 L/min rated flow, 20 m rated head, 50 m maximum head and 750 W output power. Malaysian listings specify the APSM 75AT as 0.75 kW / 1 HP, 220 V, 1" × 1", with 8 m maximum suction.

0.75 kW / 1.0 HP Motor

The APSM 75AT is powered by a 0.75 kW / 1.0 HP single-phase motor.

This is the highest-powered model in the APSm-AT group commonly listed alongside the APSM 37AT and APSM 60AT, making it suitable where greater pressure and water delivery are required.

Typical applications include:

  • Domestic water supply
  • Garden irrigation
  • Automatic sprinkler systems
  • Water tank transfer
  • Pressure boosting
  • Small agricultural irrigation
  • Utility-water systems
  • Small air-conditioning support systems

Automatic Self-Priming Design

The APSM 75AT combines a peripheral pump hydraulic system with automatic control and self-priming capability.

The automatic system is designed to detect water entering the pump and control pump operation accordingly. It also provides status indication for:

  • Power Up
  • Running
  • No Water

This reduces the need for manual pump switching in suitable domestic and garden installations.

2-Second Delayed Start

The APSM 75AT incorporates a 2-second delayed start. This is designed to reduce the potential danger associated with electrical sparks during immediate starting.

The feature is particularly useful for an automatic pump because the motor may start automatically when the system detects water demand.

50 m Maximum Head

The APSM 75AT has a maximum head of 50 m. The manufacturer's technical data shows a hydraulic operating range from approximately 45 m down to 5 m, with 50 m maximum head.

A 50 m water head corresponds to approximately 4.9 bar of theoretical static pressure.

However, maximum head is achieved at very low or zero flow. It should not be interpreted as the pressure available at the pump's maximum flow.

For actual system design, consider:

Static elevation + pipe friction + fittings + required outlet pressure = Total Dynamic Head

Rated Duty: 28 L/min at 20 m Head

The manufacturer's technical table gives the APSm75AT a rated flow of 28 L/min at a rated head of 20 m.

This is a particularly useful specification for product selection because it provides a representative operating point rather than only the maximum figures.

At approximately 28 L/min and 20 m head, the pump is operating within a more practical portion of its performance range.

The actual duty point will vary according to the connected piping system.

5–45 L/min Flow Range

The published maximum flow range is 5–45 L/min, equivalent to approximately 0.3–2.7 m³/h.

The pump therefore provides useful capacity for:

  • Household water supply
  • Garden hoses
  • Small sprinklers
  • Irrigation
  • Tank transfer
  • Water boosting

As with all centrifugal/peripheral pumps, increasing system resistance causes flow to decrease.

8 m Maximum Suction

The APSM 75AT has a specified maximum suction of 8 m.

This permits surface installation above a suitable water source within the pump's practical suction limit.

Possible water sources include:

  • Ground storage tanks
  • Rainwater tanks
  • Shallow wells
  • Reservoirs
  • Water collection tanks

Actual suction performance depends on:

  • Suction-pipe diameter
  • Suction-pipe length
  • Pipe fittings
  • Foot valve
  • Water temperature
  • Atmospheric pressure
  • Water level
  • Air leakage

For best results, install the pump as close to the water source as practical.

Peripheral Pump Hydraulic Design

The APSM 75AT uses a peripheral hydraulic configuration.

Peripheral pumps are suitable for applications where relatively high pressure is required from a compact pump while the required water volume is moderate.

This makes the APSM 75AT appropriate for:

  • Domestic pressure boosting
  • Small irrigation systems
  • Sprinkler systems
  • Household water transfer
  • Garden water supply

LEO specifically identifies the APSm-AT range for small living-water supply, automatic sprinklers and small air-conditioning systems/support equipment.

Stainless-Steel Pump Body

The APSM 75AT is specified with a stainless-steel pump body.

Stainless-steel construction provides:

  • Good corrosion resistance
  • Improved durability
  • Reduced risk of surface rust
  • Suitable performance in humid environments
  • Easy cleaning
  • Suitable appearance for domestic installations

This is particularly useful for pumps installed in outdoor or damp utility areas.

Stainless-Steel Impeller

The APSM 75AT uses a stainless-steel impeller.

The impeller transfers rotational energy from the motor to the water and is one of the primary hydraulic components.

Stainless steel provides good resistance to corrosion under normal clean-water conditions.

AISI 304 Stainless-Steel Shaft

The shaft is manufactured using AISI 304 stainless steel.

The shaft connects the motor's rotational output to the impeller and operates within the pump's wet environment.

AISI 304 offers good corrosion resistance for normal fresh-water applications.

Copper Motor Winding

The APSM 75AT uses copper motor winding.

Copper provides good electrical conductivity and contributes to reliable motor operation.

The pump should nevertheless be connected to the correct voltage and protected by an appropriately rated electrical circuit.

Built-In Thermal Protector

A built-in thermal protector is included in the motor.

The thermal protection helps protect the motor against excessive temperature caused by abnormal operating conditions.

Possible causes of motor overheating include:

  • Excessive load
  • Mechanical obstruction
  • Incorrect voltage
  • Restricted ventilation
  • Excessive ambient temperature
  • Prolonged abnormal operation

Thermal protection is supplementary and should not replace proper circuit protection.

Class F Insulation

The motor uses Class F insulation.

This provides good thermal resistance and is appropriate for normal pump operation when the unit is correctly installed and operated.

IPX4 Protection

The pump is specified with IPX4 protection.

This provides protection against water splashing from different directions.

The pump should still be protected from:

  • Flooding
  • Standing water
  • Submersion
  • High-pressure water spray
  • Prolonged severe weather exposure

Install the pump in a dry, ventilated location.

Automatic No-Water Protection

The APSM 75AT incorporates non-water/no-water protection and automatic detection of whether water is entering the pump inlet.

This is useful when the pump draws water from tanks or other sources where the water supply can become temporarily unavailable.

Correct suction installation and adequate water supply remain essential.

1" × 1" Inlet and Outlet

The APSM 75AT uses 1-inch inlet and 1-inch outlet connections.

These connections are suitable for common domestic plumbing and garden irrigation systems.

For best suction performance:

  • Keep the suction pipe as short as practical.
  • Minimize bends.
  • Avoid unnecessary reducers.
  • Ensure all joints are airtight.
  • Use an appropriate foot valve/check valve.
  • Keep the suction line free from leaks.

Domestic Water Supply

The APSM 75AT is suitable for domestic clean-water supply applications where the required duty point falls within its performance curve.

Potential applications include:

  • Household water transfer
  • Storage tank supply
  • Outdoor taps
  • Garden taps
  • Low-pressure water boosting
  • Utility water systems

The 1 HP motor provides more capacity than the APSM 37AT and APSM 60AT, making the APSM 75AT more suitable where higher pressure or flow is required.

Garden Irrigation

The APSM 75AT is particularly useful for garden irrigation and sprinkler systems.

Applications include:

  • Lawn sprinklers
  • Garden hoses
  • Landscape irrigation
  • Flower-bed irrigation
  • Vegetable gardens
  • Greenhouses
  • Small agricultural plots

Its 45 L/min maximum flow and 50 m maximum head provide a useful combination for small-to-medium irrigation requirements.

Automatic Sprinkler Systems

LEO specifically identifies the APSm-AT range as suitable for automatic water sprinkler systems.

The automatic start/stop functionality makes it convenient for sprinkler systems that operate according to water demand.

Before installation, ensure the sprinkler system's required pressure and flow are compatible with the pump's performance curve.

Water Tank Transfer

The APSM 75AT can be used for clean-water transfer between tanks.

Typical configurations include:

Ground tank → APSM 75AT → elevated tank

Rainwater tank → APSM 75AT → garden irrigation

Storage tank → APSM 75AT → household water system

The actual transfer rate depends on vertical elevation and pipe-system resistance.

Small Air-Conditioning Applications

LEO identifies the APSm-AT range as suitable for small air-conditioning systems or supporting equipment.

The suitability depends on the required flow, pressure, water temperature and system design.

For closed-loop HVAC systems, verify the required operating temperature and fluid characteristics before installation.

Clean-Water Applications

The APSM 75AT is intended for clean water or liquids with physical and chemical characteristics similar to water.

Suitable applications include:

  • Fresh water
  • Filtered rainwater
  • Storage-tank water
  • Clean groundwater
  • Irrigation water
  • Utility water

It should not be used for:

  • Sewage
  • Sludge
  • Mud
  • Heavy sand
  • Abrasive slurry
  • Fibrous wastewater
  • Liquids containing large solids

Where sediment is present, install suitable filtration upstream of the pump.

Compact Design

The APSM 75AT is listed with dimensions of approximately 300 × 300 × 250 mm and a weight of 10.2 kg.

This compact form factor is useful for:

  • Residential pump rooms
  • Garden pump installations
  • Utility areas
  • Water-tank installations
  • Small equipment rooms

Adequate clearance should be maintained for cooling and servicing.

Applications

The LEO APSM 75AT is suitable for:

  1. Domestic water supply
  2. Garden irrigation
  3. Automatic sprinkler systems
  4. Water tank transfer
  5. Domestic pressure boosting
  6. Rainwater distribution
  7. Shallow-well water supply
  8. Small agricultural irrigation
  9. Small air-conditioning support systems
  10. General clean-water transfer
  11. Household utility-water systems
  12. Landscape irrigation
  13. Small commercial water systems

Key Advantages

The LEO APSM 75AT provides:

  • 0.75 kW / 1.0 HP motor
  • 220 V single-phase operation
  • 5–45 L/min flow range
  • 50 m maximum head
  • 28 L/min rated flow
  • 20 m rated head
  • 8 m maximum suction
  • 1" × 1" connections
  • Automatic self-priming operation
  • Automatic water detection
  • No-water protection
  • 2-second delayed start
  • Power/Running/No-Water status display
  • Stainless-steel pump body
  • Stainless-steel impeller
  • AISI 304 stainless-steel shaft
  • Copper motor winding
  • Built-in thermal protection
  • Class F insulation
  • IPX4 protection
  • Anti-rust treatment of wetted parts
  • Compact installation footprint

APSM 37AT vs APSM 60AT vs APSM 75AT

Specification APSM 37AT APSM 60AT APSM 75AT
Motor Power 0.37 kW / 0.5 HP 0.6 kW / 0.8 HP 0.75 kW / 1.0 HP
Flow Range 5–30 L/min* 5–40 L/min* 5–45 L/min
Rated Flow 20 L/min 30 L/min 28 L/min
Rated Head 15 m 15 m 20 m
Maximum Head 35 m 40 m 50 m
Maximum Suction 8 m 8 m 8 m
Inlet / Outlet 1" × 1" 1" × 1" 1" × 1"
Automatic Function Yes Yes Yes
Pump Design Peripheral Peripheral Peripheral

*The manufacturer's technical table lists APSm37AT at 5–30 L/min and APSm60AT at 5–40 L/min; some Malaysian product listings may present slightly different ranges. The APSm75AT is listed at 5–45 L/min.

The APSM 75AT is the higher-capacity option of these three models, providing the highest maximum head and maximum flow within this group.

Installation Recommendations

For reliable operation:

  • Install the pump on a firm, level foundation.
  • Position it as close as practical to the water source.
  • Keep the suction pipe short and straight.
  • Use an appropriately sized 1" suction pipe.
  • Ensure all suction connections are completely airtight.
  • Install a suitable foot valve/check valve where required.
  • Prime the pump correctly before initial operation.
  • Ensure adequate water is available at the source.
  • Do not run the pump dry.
  • Provide adequate motor ventilation.
  • Protect the pump from flooding.
  • Install appropriate electrical protection and earthing.
  • Clean suction filters periodically.
  • Avoid excessive restrictions on the suction side.

Important Selection Note

The 50 m maximum head should not be used as the expected operating pressure at the maximum 45 L/min flow. The manufacturer's data separately identifies 28 L/min at 20 m as the rated duty point, which is a more useful reference when assessing a typical installation.

For an exact installation, select the pump based on the intersection of the system curve and pump performance curve, taking into account static head, pipe friction, fittings and required terminal pressure.

Product Description

LEO APSM 75AT 0.75kW 1HP Automatic Self-Priming Peripheral Water Pump is a high-performance automatic water pump designed for domestic water supply, garden irrigation, automatic sprinkler systems, water tank transfer, pressure boosting and other clean-water applications. It provides a 5–45 L/min flow range, 50 m maximum head, 28 L/min rated flow at 20 m rated head, and 8 m maximum suction, with standard 1" × 1" inlet and outlet connections.

The APSM 75AT features automatic water detection, no-water protection, 2-second delayed start and Power Up/Running/No Water status indication. Its construction includes a stainless-steel pump body and impeller, AISI 304 stainless-steel shaft, copper motor winding, built-in thermal protector, Class F insulation and IPX4 protection.

With its 1.0 HP motor, automatic self-priming operation and 50 m maximum head, the LEO APSM 75AT is suitable for homeowners, gardens, irrigation systems and small commercial clean-water applications requiring greater pressure and capacity than smaller automatic pump models.

SEO Product Title

LEO APSM 75AT 0.75kW 1HP 220V Automatic Self-Priming Peripheral Water Pump 50m Head

Short Product Description

LEO APSM 75AT is a 0.75kW / 1HP 220V automatic self-priming peripheral water pump designed for domestic water supply, garden irrigation, automatic sprinklers, water tank transfer and pressure boosting. It provides 5–45 L/min flow, 50 m maximum head, 28 L/min rated flow at 20 m head and 8 m maximum suction, with 1" × 1" connections. The pump features automatic water detection, no-water protection, 2-second delayed start, operating-status display, stainless-steel pump body and impeller, AISI 304 shaft, copper winding, thermal protection, Class F insulation and IPX4 protection.



 Inquiry - LEO AUTOMATIC SELF-PRIMING PUMP - APSM 75AT