B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO INTELLIGENT BOOSTER PUMP - PQ50E-1



The LEO PQ50E-1 is a compact intelligent automatic peripheral booster pump designed to improve water pressure and provide automatic water supply for residential and light-duty applications. It combines a 0.37 kW / 0.5 HP motor with an integrated intelligent control system that automatically starts and stops the pump according to water demand. Published specifications give a 0–33 L/min flow range, 0–35 m maximum head, and 1" inlet/outlet connections.

The PQ50E-1 is particularly suitable for homes, apartments, gardens, water tanks and other installations requiring compact, automatic and relatively quiet pressure boosting.

Technical Specifications

Specification LEO PQ50E-1
Brand LEO
Model PQ50E-1
Pump Type Intelligent Automatic Peripheral Booster Pump
Motor Power 0.37 kW / 0.5 HP
Supply Voltage 220 V AC
Phase Single Phase
Frequency 50 Hz
Flow Range 0–33 L/min
Maximum Flow Approx. 2.0 m³/h
Head Range 0–35 m
Maximum Head 35 m
Inlet 1"
Outlet 1"
Maximum Liquid Temperature 60°C
Protection Class IPX4
Insulation Class F
Impeller Brass
Thermal Protection Built-In
Dry-Running Protection Yes
Low-Water Protection Yes
Anti-Blocking Protection Yes
Delayed-Start Protection Yes
Automatic Operation Yes
Dimensions 300 × 300 × 250 mm
Weight 5.2 kg

These specifications are published by Malaysian LEO distributors for the PQ50E-1.

0.37 kW / 0.5 HP Motor

The PQ50E-1 uses a 0.37 kW / 0.5 HP single-phase motor. It is designed for relatively small water-pressure boosting applications rather than high-volume commercial pumping.

The compact motor provides sufficient power for applications such as:

  • Household water boosting
  • Bathroom water-pressure improvement
  • Kitchen water supply
  • Garden watering
  • Water tank distribution
  • Small irrigation systems
  • Domestic utility water systems

Intelligent Automatic Control

The key feature of the PQ50E-1 is its integrated intelligent control system.

Instead of requiring a conventional manual switch, the pump responds automatically to water demand. When a water outlet is opened, the system detects the demand and operates the pump; when water demand stops, the pump stops automatically.

This makes the pump convenient for household installations where water pressure needs to be maintained without manually switching the pump on and off.

Automatic Water Pressure Boosting

The PQ50E-1 is designed primarily as a water-pressure booster.

Typical installation:

Water source → PQ50E-1 → Household piping → Taps / Shower / Garden

The pump increases the available pressure in the downstream pipework, helping improve water delivery at outlets where existing pressure is insufficient.

It is particularly useful for:

  • Low-pressure household water systems
  • Elevated storage tanks
  • Direct water supply
  • Bathroom shower systems
  • Kitchen taps
  • Garden taps

0–33 L/min Flow Capacity

The published maximum flow range is 0–33 L/min, equivalent to approximately 2.0 m³/h.

This makes the pump suitable for small domestic water-demand applications.

The actual flow will depend on the required pressure/head and the resistance of the connected pipework.

As with other centrifugal/peripheral pumps:

Higher system head = lower available flow

Lower system head = higher available flow

Therefore, the 33 L/min figure should be treated as a maximum published capacity rather than the flow available at maximum pressure.

35 m Maximum Head

The PQ50E-1 has a published maximum head of 35 m.

A 35 m water head corresponds to approximately 3.4 bar of theoretical static pressure.

The actual pressure available at a household tap will be lower depending on:

  • Pipe length
  • Pipe diameter
  • Number of fittings
  • Elevation
  • Valves
  • Filters
  • Simultaneous water usage

For proper pump selection, the pump's hydraulic performance should be matched to the required system duty point.

Brass Impeller

The PQ50E-1 is equipped with a brass impeller.

Brass provides good mechanical durability and corrosion resistance for normal clean-water applications.

The impeller is responsible for transferring rotational energy from the motor into the water, generating the required pressure and flow.

Dry-Running Protection

The PQ50E-1 includes dry-running protection.

Dry running occurs when the pump operates without an adequate water supply. This can cause overheating and premature wear of internal components.

The intelligent control system is designed to detect abnormal water conditions and protect the pump.

However, proper installation and ensuring adequate water availability remain important.

Low-Water-Level Protection

The pump also incorporates low-water-level protection.

This is particularly useful when the pump draws water from a storage tank.

If the water level becomes insufficient, the control system can prevent inappropriate operation and reduce the risk of damage caused by insufficient water.

Typical applications include:

  • Ground tanks
  • Roof tanks
  • Rainwater tanks
  • Storage reservoirs

Anti-Blocking Protection

The PQ50E-1 features anti-blocking protection.

This function helps reduce the possibility of the pump becoming stuck after extended periods of inactivity.

An anti-blocking function is particularly useful for domestic pumps that may not operate continuously throughout the day.

Automatic Periodic Running

Published Malaysian product information states that the PQ50E-1 can run for approximately 10 seconds every 12 hours during extended periods of non-use to help prevent congestion/blocking.

This is useful for installations where the pump may remain inactive for long periods.

Delayed-Start Protection

The intelligent controller incorporates delay-start protection.

This allows the pump to start in a controlled manner when water demand is detected and helps prevent undesirable rapid or uncontrolled starting.

Automatic Stop

The PQ50E-1 automatically stops when the water demand ends.

For example:

Tap closed → water flow stops → controller detects no demand → pump stops

This eliminates the need for the user to manually switch the pump off after every use.

1" Inlet and Outlet

The PQ50E-1 uses 1-inch inlet and outlet connections.

These connections are suitable for common domestic plumbing systems.

For optimum performance:

  • Use correctly sized pipework.
  • Avoid unnecessary restrictions.
  • Minimize sharp bends.
  • Keep the suction side as short as practical.
  • Ensure all connections are properly sealed.
  • Clean filters regularly if installed.

Maximum Liquid Temperature: 60°C

The specified maximum liquid temperature is 60°C.

This means the pump is suitable for water within the manufacturer's specified temperature limit.

For normal household applications such as cold-water boosting, the pump operates well below this limit.

The pump should not be used for liquids exceeding the specified temperature.

IPX4 Protection

The PQ50E-1 is specified with IPX4 protection.

This provides protection against water splashing from different directions.

The pump should nevertheless be installed in a location protected from:

  • Flooding
  • Standing water
  • Submersion
  • High-pressure water spray
  • Severe weather exposure

A dry and adequately ventilated installation location is recommended.

Class F Insulation

The motor is specified with Class F insulation.

Class F insulation provides good thermal resistance and is suitable for the motor's intended operating conditions.

Correct electrical supply and adequate ventilation are still required for reliable operation.

Built-In Thermal Protector

The PQ50E-1 incorporates a built-in thermal protector.

The thermal protector helps protect the motor if excessive temperature develops due to abnormal operating conditions.

Potential causes of overheating can include:

  • Motor overload
  • Mechanical blockage
  • Incorrect voltage
  • Poor ventilation
  • Excessive ambient temperature
  • Abnormal operating conditions

The thermal protector should supplement, rather than replace, appropriate electrical circuit protection.

Compact and Lightweight Design

The published dimensions are approximately 300 × 300 × 250 mm, with a listed weight of only 5.2 kg.

This makes the PQ50E-1 particularly convenient for installations where available space is limited.

Suitable locations include:

  • Small pump rooms
  • Under-stair utility areas
  • Residential service areas
  • Water-tank areas
  • Compact mechanical rooms
  • Garden pump installations

A Malaysian supplier also describes the PQ50E-1 as suitable for confined spaces and highlights its compact, attractive design.

Quiet Automatic Operation

The PQ50E-1 is marketed as a silent/low-noise automatic water pump, making it suitable for residential environments where excessive pump noise can be undesirable.

Correct mounting on a solid and stable surface is important for minimizing vibration and transmitted noise.

Household Water Pressure Boosting

One of the primary applications of the PQ50E-1 is improving insufficient household water pressure.

It can be used to support:

  • Showers
  • Bathroom taps
  • Kitchen taps
  • Washing machines
  • Outdoor taps
  • Small household water outlets

Where multiple outlets are used simultaneously, the available flow will depend on the pump's performance and the system's total resistance.

Garden Watering

The pump can be used for small garden-water applications.

Examples include:

  • Garden hoses
  • Small sprinklers
  • Flower-bed irrigation
  • Vegetable gardens
  • Landscape watering
  • Small greenhouse systems

The automatic control allows the pump to start when water is required and stop after demand ends.

Water Tank Applications

The PQ50E-1 can be incorporated into suitable tank-based water systems.

Typical arrangement:

Storage tank → PQ50E-1 → Household outlets

The pump can provide additional pressure to downstream outlets where gravity-fed pressure from the tank is insufficient.

Clean-Water Applications

The PQ50E-1 is intended for normal water-pumping applications. It should be used with clean water or liquids compatible with the pump's materials and specifications.

Suitable applications include:

  • Fresh water
  • Filtered rainwater
  • Household storage-tank water
  • Clean utility water
  • Garden irrigation water

It should not be selected for:

  • Sewage
  • Mud
  • Sludge
  • Heavy sediment
  • Abrasive slurry
  • Fibrous wastewater
  • Liquids containing large solids

Intelligent Protection System

The PQ50E-1 combines several protective functions in its control system:

  1. Dry-running protection
  2. Low-water-level protection
  3. Anti-blocking protection
  4. Delayed-start protection
  5. Automatic start/stop
  6. Built-in thermal protection

These functions reduce the amount of manual monitoring required during normal domestic operation.

Main Applications

The LEO PQ50E-1 is suitable for:

  1. Domestic water pressure boosting
  2. Household water supply
  3. Bathroom shower boosting
  4. Kitchen water supply
  5. Garden watering
  6. Small sprinkler systems
  7. Water tank pressure boosting
  8. Rainwater distribution
  9. Small irrigation systems
  10. Utility water transfer
  11. Residential water systems
  12. Light-duty commercial water supply

Key Advantages

The LEO PQ50E-1 offers:

  • 0.37 kW / 0.5 HP motor
  • 220 V single-phase operation
  • 0–33 L/min flow capacity
  • 35 m maximum head
  • 1" inlet and outlet
  • Brass impeller
  • Automatic start/stop
  • Intelligent water-demand control
  • Dry-running protection
  • Low-water protection
  • Anti-blocking protection
  • Delayed-start protection
  • Automatic periodic anti-blocking operation
  • Built-in thermal protector
  • Maximum liquid temperature of 60°C
  • IPX4 protection
  • Class F insulation
  • Compact dimensions
  • Lightweight 5.2 kg construction
  • Suitable for confined spaces
  • Low-noise operation

Installation Recommendations

For reliable performance:

  • Install the pump on a firm, level surface.
  • Position it close to the water source where possible.
  • Use correctly sized 1" pipework.
  • Avoid excessive bends and restrictions.
  • Ensure pipe connections are properly sealed.
  • Install suitable filtration where the water contains sediment.
  • Ensure adequate water is available before operation.
  • Do not intentionally operate the pump without water.
  • Provide adequate ventilation around the motor.
  • Protect the pump from flooding and direct high-pressure water.
  • Use suitable electrical protection and proper earthing.
  • Clean filters periodically.
  • Ensure the pump is accessible for maintenance.

Product Description

LEO PQ50E-1 0.37kW 0.5HP Intelligent Automatic Peripheral Booster Pump is a compact and efficient water-pressure booster designed for domestic water supply, household pressure boosting, garden watering, water tank systems and small irrigation applications. It provides up to 33 L/min flow and 35 m maximum head, with standard 1" inlet and outlet connections.

The pump features an intelligent automatic control system that starts and stops the pump according to water demand. Integrated dry-running protection, low-water-level protection, anti-blocking protection, delayed-start protection and built-in thermal protection help improve operational safety and reliability.

With a brass impeller, 220 V single-phase 0.5 HP motor, IPX4 protection, Class F insulation and compact 5.2 kg design, the LEO PQ50E-1 is a practical solution for residential installations requiring automatic and convenient water-pressure boosting.

SEO Product Title

LEO PQ50E-1 0.37kW 0.5HP 220V Intelligent Automatic Peripheral Water Booster Pump

Short Product Description

LEO PQ50E-1 is a 0.37kW / 0.5HP 220V intelligent automatic peripheral booster pump designed for household water-pressure boosting, garden watering, water tank systems and small irrigation applications. It provides up to 33 L/min flow and 35 m maximum head, with 1" inlet and outlet connections. Features include automatic start/stop, dry-running protection, low-water protection, anti-blocking protection, delayed-start protection, brass impeller, built-in thermal prot ection, IPX4 protection and Class F insulation.



 Inquiry - LEO INTELLIGENT BOOSTER PUMP - PQ50E-1