B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO PERIPHERAL, SELF-PRIMING PERIPEHRAL PUMPS - XKM 50-1



The LEO XKm50-1 is a compact peripheral water pump designed for clean-water transfer, small domestic water supply, garden irrigation, sprinkler systems and water-pressure boosting. It is powered by a 0.11 kW / 0.15 HP, 220 V single-phase motor and provides a maximum flow of approximately 25 L/min with a maximum head of approximately 22 m. LEO officially lists the XKm series for clean-water transfer, small domestic water supply, automatic sprinklers and small air-conditioning/support equipment.

A technical point for cataloguing: XKm50-1 is officially classified by LEO as a Peripheral Pump, rather than the separate APSm self-priming series. It has a stated maximum suction lift of 8 m, but should not be described as having the same self-priming construction/function as an APSm model unless the specific supplied unit is a self-priming variant.

Technical Specifications

Specification LEO XKm50-1
Brand LEO
Model XKm50-1
Pump Type Peripheral Pump
Motor Power 0.11 kW / 0.15 HP
Voltage 220 V
Phase Single Phase
Frequency 50 Hz
Maximum Flow 25 L/min
Maximum Flow Approx. 1.5 m³/h
Maximum Head 22 m
Head Range Approx. 22–3 m
Maximum Suction 8 m
Inlet / Outlet 1" × 1"
Impeller Brass
Pump Body HT200 Cast Iron with Anti-Rust Treatment
Pump Support HT200 Cast Iron with Anti-Rust Treatment
Shaft AISI 304 Stainless Steel
Mechanical Seal Carbon / Ceramic
O-Ring NBR
Motor Winding Copper
Thermal Protection Built-In
Insulation Class F
Protection Class IPX4
Maximum Liquid Temperature 60°C
Maximum Ambient Temperature 50°C
Bearing Low-Noise / Long-Life Type
Suitable Liquid Clean Water / Similar Liquids

The XKm50-1 performance data show 0–25 L/min corresponding to approximately 22–3 m head; the model is rated at 0.11 kW / 0.15 HP.

0.11 kW / 0.15 HP Motor

The XKm50-1 uses a compact 0.11 kW / 0.15 HP single-phase motor operating at 220 V. This makes it suitable for relatively small water-transfer and pressure-boosting duties where a larger 0.5–1 HP pump would be unnecessary.

The low-power motor is particularly appropriate for:

  • Small household water systems
  • Garden watering
  • Small irrigation applications
  • Water-pressure boosting
  • Small sprinkler systems
  • Utility water transfer
  • Small equipment-support systems

Peripheral Pump Design

The XKm50-1 uses a peripheral/vortex-type hydraulic design. Peripheral pumps are compact and capable of generating relatively high pressure for their physical size and motor power.

The hydraulic design is particularly suitable when the application requires:

  • Moderate water flow
  • Relatively high pressure
  • Compact pump dimensions
  • Low electrical power consumption
  • Domestic water transfer

The published performance curve shows the XKm50-1 delivering approximately 25 L/min at low head, with head increasing as flow decreases, reaching approximately 22 m at zero flow.

25 L/min Maximum Flow

The XKm50-1 has a maximum published flow of approximately 25 L/min, equivalent to 1.5 m³/h.

This capacity makes the pump suitable for small water requirements such as:

  • Garden hoses
  • Small sprinklers
  • Household taps
  • Small irrigation lines
  • Water transfer between small tanks
  • Utility water applications

The actual flow decreases as system head increases.

22 m Maximum Head

The XKm50-1 provides a maximum head of approximately 22 m. Its published performance curve indicates:

Flow Approx. Head
0 L/min 22 m
5 L/min 19 m
10 L/min 15 m
15 L/min 11 m
20 L/min 7 m
25 L/min 3 m

These figures demonstrate the pump's normal pump-curve relationship: higher flow is available at lower system resistance, while higher head is available at lower flow.

A 22 m water head corresponds to approximately 2.16 bar of theoretical static pressure.

8 m Maximum Suction

The XKm50-1 is specified with a maximum suction lift of 8 m.

This makes it suitable for installations where the pump is located above a water source, subject to correct pipework and actual site conditions.

Possible water sources include:

  • Storage tanks
  • Small reservoirs
  • Shallow wells
  • Rainwater tanks
  • Groundwater sources

For reliable suction performance, the suction pipe should be properly sealed and kept as short and direct as practical.

Brass Impeller

The XKm50-1 is equipped with a brass impeller.

Brass provides good corrosion resistance and mechanical durability for normal clean-water pumping.

The impeller is responsible for converting the motor's rotational energy into hydraulic energy, producing the required water flow and pressure.

Anti-Rust Cast-Iron Pump Body

The pump body and support are constructed from HT200 cast iron and receive a special anti-rust treatment.

This provides a durable housing for the hydraulic components while improving resistance to corrosion during normal use.

The construction is suitable for:

  • Indoor pump rooms
  • Utility areas
  • Garden installations
  • Small irrigation systems
  • Residential water systems

AISI 304 Stainless-Steel Shaft

The XKm50-1 uses an AISI 304 stainless-steel shaft.

The shaft transfers rotational power from the motor to the brass impeller and provides good corrosion resistance in normal clean-water service.

Carbon/Ceramic Mechanical Seal

The mechanical seal is specified as carbon/ceramic.

The mechanical seal helps prevent water from escaping along the rotating shaft into the motor area.

Proper operation requires the pump to be used within its specified liquid-temperature and pressure conditions.

Copper Motor Winding

The XKm50-1 motor uses copper winding.

Copper provides good electrical conductivity and contributes to reliable motor operation.

Correct voltage, appropriate electrical protection and adequate motor ventilation are still required.

Built-In Thermal Protection

The single-phase motor incorporates a built-in thermal protector.

This helps protect the motor from excessive temperature caused by abnormal operating conditions.

Potential causes of overheating include:

  • Motor overload
  • Mechanical obstruction
  • Incorrect supply voltage
  • Poor ventilation
  • Excessive ambient temperature
  • Prolonged abnormal operation

Class F Insulation

The motor is specified with Class F insulation.

This provides good thermal resistance for normal motor operation and is appropriate for the pump's intended applications.

IPX4 Protection

The motor enclosure is specified as IPX4.

This provides protection against water splashing from different directions.

The pump should nevertheless be installed in a location protected from:

  • Flooding
  • Standing water
  • Submersion
  • High-pressure water spray
  • Severe weather exposure

Maximum Liquid Temperature

The XKm50-1 is listed with a maximum liquid temperature of 60°C in the Malaysian product specification.

For normal domestic, garden and irrigation applications, the pump will generally operate with considerably cooler water.

The pump should not be used with liquids exceeding the specified temperature limit.

Maximum Ambient Temperature

The Malaysian specification lists a maximum ambient temperature of 50°C.

Adequate ventilation around the motor is important, particularly when the pump is installed in an enclosed pump room or outdoor cabinet.

1" × 1" Connections

The XKm50-1 uses 1-inch inlet and 1-inch outlet connections.

These connections are convenient for common domestic and garden plumbing.

For optimum hydraulic performance:

  • Avoid unnecessary pipe reductions.
  • Keep the suction line short.
  • Minimize sharp bends.
  • Use suitable valves and fittings.
  • Ensure suction connections are airtight.
  • Keep filters clean.

Domestic Water Supply

The XKm50-1 is suitable for small domestic water-supply applications.

Typical applications include:

  • Small household water transfer
  • Tank water supply
  • Garden taps
  • Utility outlets
  • Small pressure-boosting systems

The pump should be selected according to the actual required flow and total system head.

Garden Irrigation

The pump is well suited to small garden irrigation applications.

Possible uses include:

  • Garden hoses
  • Small sprinklers
  • Flower beds
  • Vegetable gardens
  • Small greenhouses
  • Landscape irrigation

Its compact 0.15 HP motor is appropriate for relatively low water-demand systems.

Automatic Sprinkler Systems

LEO identifies the XKm series as suitable for automatic water sprinkler systems.

For an automatic sprinkler application, verify that the sprinkler system's pressure and flow requirements fall within the XKm50-1 pump curve.

Water Pressure Boosting

The XKm50-1 can be used for small water-pressure boosting duties.

Typical arrangement:

Water source → XKm50-1 → Household/Garden Pipework → Water Outlet

Because the pump's maximum head is approximately 22 m, it is best suited to relatively small systems rather than high-pressure multi-storey installations.

Small Air-Conditioning Support

LEO lists small air-conditioning systems or supporting equipment among the applications of the XKm series.

For such applications, verify:

  • Required flow
  • Required head
  • Fluid temperature
  • Fluid compatibility
  • Operating cycle

Clean-Water Applications

The XKm series is intended for clean water or liquids with physical and chemical properties similar to water.

Suitable applications include:

  • Fresh water
  • Clean storage-tank water
  • Filtered rainwater
  • Clean irrigation water
  • Utility water

It is not appropriate for:

  • Sewage
  • Mud
  • Sludge
  • Heavy sediment
  • Abrasive slurry
  • Fibrous wastewater
  • Liquids containing large solids

If the water contains sediment, an appropriate filter should be installed before the pump.

Compact Pump for Small Installations

The XKm50-1 is designed as a compact peripheral pump, making it practical where installation space is limited.

Suitable installation areas include:

  • Small pump rooms
  • Garden pump areas
  • Utility rooms
  • Tank areas
  • Residential service areas
  • Small irrigation installations

Its relatively low motor power also makes it appropriate for smaller water systems.

Important Note on "Self-Priming"

The product name supplied is "LEO PERIPHERAL, SELF-PRIMING PERIPHERAL PUMPS – XKM 50-1." For technical accuracy, the official LEO website categorizes XKm as a Peripheral Pump, while LEO has a separate APSm Self-Priming Peripheral Pump series.

Therefore, for a website catalogue, the safest technical description is:

LEO XKm50-1 Peripheral Water Pump

rather than presenting it as an APSm-style automatic self-priming pump.

The XKm50-1 does have a published maximum suction lift of 8 m, but this specification should not by itself be used to equate it with the dedicated APSm self-priming series.

Main Applications

The LEO XKm50-1 is suitable for:

  1. Small domestic water supply
  2. Garden irrigation
  3. Garden sprinkler systems
  4. Water pressure boosting
  5. Small water transfer
  6. Small storage-tank systems
  7. Rainwater distribution
  8. Shallow-water-source applications
  9. Small air-conditioning support systems
  10. Utility water transfer
  11. Small landscape irrigation
  12. General clean-water pumping

Key Advantages

The LEO XKm50-1 offers:

  • 0.11 kW / 0.15 HP motor
  • 220 V single-phase operation
  • 25 L/min maximum flow
  • 22 m maximum head
  • 8 m maximum suction
  • 1" × 1" connections
  • Brass impeller
  • AISI 304 stainless-steel shaft
  • Anti-rust-treated HT200 cast-iron pump body
  • Carbon/ceramic mechanical seal
  • Copper motor winding
  • Built-in thermal protection
  • Class F insulation
  • IPX4 protection
  • Low-noise, long-life bearing design
  • Compact peripheral-pump construction
  • Suitable for clean-water applications

Installation Recommendations

For reliable operation:

  • Install the pump on a firm, level surface.
  • Position it as close to the water source as practical.
  • Keep the suction pipe short and direct.
  • Use appropriate 1" pipework.
  • Ensure all suction joints are airtight.
  • Minimize bends and restrictions.
  • Use a suitable foot valve/check valve where required.
  • Ensure sufficient water is available before starting.
  • Avoid prolonged dry operation.
  • Provide adequate motor ventilation.
  • Protect the pump from flooding and submersion.
  • Install appropriate electrical protection and earthing.
  • Clean suction filters regularly where sediment is present.

Performance Summary

Performance Point XKm50-1
Maximum Flow 25 L/min
Maximum Flow 1.5 m³/h
Maximum Head 22 m
At 5 L/min 19 m head
At 10 L/min 15 m head
At 15 L/min 11 m head
At 20 L/min 7 m head
At 25 L/min 3 m head
Maximum Suction 8 m

The performance values above are based on the published XKm50-1 hydraulic data.

Product Description

LEO XKm50-1 0.11kW 0.15HP Peripheral Water Pump is a compact and efficient 220V single-phase peripheral pump designed for small domestic water supply, garden irrigation, sprinkler systems, water-pressure boosting and clean-water transfer. It provides up to 25 L/min flow, 22 m maximum head and 8 m maximum suction, with standard 1" × 1" inlet and outlet connections.

The pump features a brass impeller, AISI 304 stainless-steel shaft, anti-rust-treated HT200 cast-iron pump body, carbon/ceramic mechanical seal, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. These features make it suitable for compact domestic, garden and light-duty clean-water pumping applications.

With its 0.15 HP motor and compact peripheral design, the LEO XKm50-1 is a practical choice for small water systems where moderate flow, useful pressure and compact installation are required.

SEO Product Title

LEO XKm50-1 0.11kW 0.15HP 220V Peripheral Water Pump – 25L/min, 22m Head

Short Product Description

LEO XKm50-1 is a 0.11kW / 0.15HP 220V peripheral water pump designed for small domestic water supply, garden irrigation, sprinkler systems, water-pressure boosting and clean-water transfer. It provides up to 25 L/min flow, 22 m maximum head and 8 m maximum suction, with 1" × 1" connections. Features include a brass impeller, AISI 304 stainless-steel shaft, anti-rust-treated cast-iron pump body, copper winding, built-in thermal protection, Class F insulation and IPX4 protection.



 Inquiry - LEO PERIPHERAL, SELF-PRIMING PERIPEHRAL PUMPS - XKM 50-1