The LEO XKm50-1 is a compact peripheral water pump designed for clean-water transfer, small domestic water supply, garden irrigation, sprinkler systems and water-pressure boosting. It is powered by a 0.11 kW / 0.15 HP, 220 V single-phase motor and provides a maximum flow of approximately 25 L/min with a maximum head of approximately 22 m. LEO officially lists the XKm series for clean-water transfer, small domestic water supply, automatic sprinklers and small air-conditioning/support equipment.
A technical point for cataloguing: XKm50-1 is officially classified by LEO as a Peripheral Pump, rather than the separate APSm self-priming series. It has a stated maximum suction lift of 8 m, but should not be described as having the same self-priming construction/function as an APSm model unless the specific supplied unit is a self-priming variant.
Technical Specifications
| Specification | LEO XKm50-1 |
|---|---|
| Brand | LEO |
| Model | XKm50-1 |
| Pump Type | Peripheral Pump |
| Motor Power | 0.11 kW / 0.15 HP |
| Voltage | 220 V |
| Phase | Single Phase |
| Frequency | 50 Hz |
| Maximum Flow | 25 L/min |
| Maximum Flow | Approx. 1.5 m³/h |
| Maximum Head | 22 m |
| Head Range | Approx. 22–3 m |
| Maximum Suction | 8 m |
| Inlet / Outlet | 1" × 1" |
| Impeller | Brass |
| Pump Body | HT200 Cast Iron with Anti-Rust Treatment |
| Pump Support | HT200 Cast Iron with Anti-Rust Treatment |
| Shaft | AISI 304 Stainless Steel |
| Mechanical Seal | Carbon / Ceramic |
| O-Ring | NBR |
| Motor Winding | Copper |
| Thermal Protection | Built-In |
| Insulation Class | F |
| Protection Class | IPX4 |
| Maximum Liquid Temperature | 60°C |
| Maximum Ambient Temperature | 50°C |
| Bearing | Low-Noise / Long-Life Type |
| Suitable Liquid | Clean Water / Similar Liquids |
The XKm50-1 performance data show 0–25 L/min corresponding to approximately 22–3 m head; the model is rated at 0.11 kW / 0.15 HP.
0.11 kW / 0.15 HP Motor
The XKm50-1 uses a compact 0.11 kW / 0.15 HP single-phase motor operating at 220 V. This makes it suitable for relatively small water-transfer and pressure-boosting duties where a larger 0.5–1 HP pump would be unnecessary.
The low-power motor is particularly appropriate for:
- Small household water systems
- Garden watering
- Small irrigation applications
- Water-pressure boosting
- Small sprinkler systems
- Utility water transfer
- Small equipment-support systems
Peripheral Pump Design
The XKm50-1 uses a peripheral/vortex-type hydraulic design. Peripheral pumps are compact and capable of generating relatively high pressure for their physical size and motor power.
The hydraulic design is particularly suitable when the application requires:
- Moderate water flow
- Relatively high pressure
- Compact pump dimensions
- Low electrical power consumption
- Domestic water transfer
The published performance curve shows the XKm50-1 delivering approximately 25 L/min at low head, with head increasing as flow decreases, reaching approximately 22 m at zero flow.
25 L/min Maximum Flow
The XKm50-1 has a maximum published flow of approximately 25 L/min, equivalent to 1.5 m³/h.
This capacity makes the pump suitable for small water requirements such as:
- Garden hoses
- Small sprinklers
- Household taps
- Small irrigation lines
- Water transfer between small tanks
- Utility water applications
The actual flow decreases as system head increases.
22 m Maximum Head
The XKm50-1 provides a maximum head of approximately 22 m. Its published performance curve indicates:
| Flow | Approx. Head |
|---|---|
| 0 L/min | 22 m |
| 5 L/min | 19 m |
| 10 L/min | 15 m |
| 15 L/min | 11 m |
| 20 L/min | 7 m |
| 25 L/min | 3 m |
These figures demonstrate the pump's normal pump-curve relationship: higher flow is available at lower system resistance, while higher head is available at lower flow.
A 22 m water head corresponds to approximately 2.16 bar of theoretical static pressure.
8 m Maximum Suction
The XKm50-1 is specified with a maximum suction lift of 8 m.
This makes it suitable for installations where the pump is located above a water source, subject to correct pipework and actual site conditions.
Possible water sources include:
- Storage tanks
- Small reservoirs
- Shallow wells
- Rainwater tanks
- Groundwater sources
For reliable suction performance, the suction pipe should be properly sealed and kept as short and direct as practical.
Brass Impeller
The XKm50-1 is equipped with a brass impeller.
Brass provides good corrosion resistance and mechanical durability for normal clean-water pumping.
The impeller is responsible for converting the motor's rotational energy into hydraulic energy, producing the required water flow and pressure.
Anti-Rust Cast-Iron Pump Body
The pump body and support are constructed from HT200 cast iron and receive a special anti-rust treatment.
This provides a durable housing for the hydraulic components while improving resistance to corrosion during normal use.
The construction is suitable for:
- Indoor pump rooms
- Utility areas
- Garden installations
- Small irrigation systems
- Residential water systems
AISI 304 Stainless-Steel Shaft
The XKm50-1 uses an AISI 304 stainless-steel shaft.
The shaft transfers rotational power from the motor to the brass impeller and provides good corrosion resistance in normal clean-water service.
Carbon/Ceramic Mechanical Seal
The mechanical seal is specified as carbon/ceramic.
The mechanical seal helps prevent water from escaping along the rotating shaft into the motor area.
Proper operation requires the pump to be used within its specified liquid-temperature and pressure conditions.
Copper Motor Winding
The XKm50-1 motor uses copper winding.
Copper provides good electrical conductivity and contributes to reliable motor operation.
Correct voltage, appropriate electrical protection and adequate motor ventilation are still required.
Built-In Thermal Protection
The single-phase motor incorporates a built-in thermal protector.
This helps protect the motor from excessive temperature caused by abnormal operating conditions.
Potential causes of overheating include:
- Motor overload
- Mechanical obstruction
- Incorrect supply voltage
- Poor ventilation
- Excessive ambient temperature
- Prolonged abnormal operation
Class F Insulation
The motor is specified with Class F insulation.
This provides good thermal resistance for normal motor operation and is appropriate for the pump's intended applications.
IPX4 Protection
The motor enclosure is specified as IPX4.
This provides protection against water splashing from different directions.
The pump should nevertheless be installed in a location protected from:
- Flooding
- Standing water
- Submersion
- High-pressure water spray
- Severe weather exposure
Maximum Liquid Temperature
The XKm50-1 is listed with a maximum liquid temperature of 60°C in the Malaysian product specification.
For normal domestic, garden and irrigation applications, the pump will generally operate with considerably cooler water.
The pump should not be used with liquids exceeding the specified temperature limit.
Maximum Ambient Temperature
The Malaysian specification lists a maximum ambient temperature of 50°C.
Adequate ventilation around the motor is important, particularly when the pump is installed in an enclosed pump room or outdoor cabinet.
1" × 1" Connections
The XKm50-1 uses 1-inch inlet and 1-inch outlet connections.
These connections are convenient for common domestic and garden plumbing.
For optimum hydraulic performance:
- Avoid unnecessary pipe reductions.
- Keep the suction line short.
- Minimize sharp bends.
- Use suitable valves and fittings.
- Ensure suction connections are airtight.
- Keep filters clean.
Domestic Water Supply
The XKm50-1 is suitable for small domestic water-supply applications.
Typical applications include:
- Small household water transfer
- Tank water supply
- Garden taps
- Utility outlets
- Small pressure-boosting systems
The pump should be selected according to the actual required flow and total system head.
Garden Irrigation
The pump is well suited to small garden irrigation applications.
Possible uses include:
- Garden hoses
- Small sprinklers
- Flower beds
- Vegetable gardens
- Small greenhouses
- Landscape irrigation
Its compact 0.15 HP motor is appropriate for relatively low water-demand systems.
Automatic Sprinkler Systems
LEO identifies the XKm series as suitable for automatic water sprinkler systems.
For an automatic sprinkler application, verify that the sprinkler system's pressure and flow requirements fall within the XKm50-1 pump curve.
Water Pressure Boosting
The XKm50-1 can be used for small water-pressure boosting duties.
Typical arrangement:
Water source → XKm50-1 → Household/Garden Pipework → Water Outlet
Because the pump's maximum head is approximately 22 m, it is best suited to relatively small systems rather than high-pressure multi-storey installations.
Small Air-Conditioning Support
LEO lists small air-conditioning systems or supporting equipment among the applications of the XKm series.
For such applications, verify:
- Required flow
- Required head
- Fluid temperature
- Fluid compatibility
- Operating cycle
Clean-Water Applications
The XKm series is intended for clean water or liquids with physical and chemical properties similar to water.
Suitable applications include:
- Fresh water
- Clean storage-tank water
- Filtered rainwater
- Clean irrigation water
- Utility water
It is not appropriate for:
- Sewage
- Mud
- Sludge
- Heavy sediment
- Abrasive slurry
- Fibrous wastewater
- Liquids containing large solids
If the water contains sediment, an appropriate filter should be installed before the pump.
Compact Pump for Small Installations
The XKm50-1 is designed as a compact peripheral pump, making it practical where installation space is limited.
Suitable installation areas include:
- Small pump rooms
- Garden pump areas
- Utility rooms
- Tank areas
- Residential service areas
- Small irrigation installations
Its relatively low motor power also makes it appropriate for smaller water systems.
Important Note on "Self-Priming"
The product name supplied is "LEO PERIPHERAL, SELF-PRIMING PERIPHERAL PUMPS – XKM 50-1." For technical accuracy, the official LEO website categorizes XKm as a Peripheral Pump, while LEO has a separate APSm Self-Priming Peripheral Pump series.
Therefore, for a website catalogue, the safest technical description is:
LEO XKm50-1 Peripheral Water Pump
rather than presenting it as an APSm-style automatic self-priming pump.
The XKm50-1 does have a published maximum suction lift of 8 m, but this specification should not by itself be used to equate it with the dedicated APSm self-priming series.
Main Applications
The LEO XKm50-1 is suitable for:
- Small domestic water supply
- Garden irrigation
- Garden sprinkler systems
- Water pressure boosting
- Small water transfer
- Small storage-tank systems
- Rainwater distribution
- Shallow-water-source applications
- Small air-conditioning support systems
- Utility water transfer
- Small landscape irrigation
- General clean-water pumping
Key Advantages
The LEO XKm50-1 offers:
- 0.11 kW / 0.15 HP motor
- 220 V single-phase operation
- 25 L/min maximum flow
- 22 m maximum head
- 8 m maximum suction
- 1" × 1" connections
- Brass impeller
- AISI 304 stainless-steel shaft
- Anti-rust-treated HT200 cast-iron pump body
- Carbon/ceramic mechanical seal
- Copper motor winding
- Built-in thermal protection
- Class F insulation
- IPX4 protection
- Low-noise, long-life bearing design
- Compact peripheral-pump construction
- Suitable for clean-water applications
Installation Recommendations
For reliable operation:
- Install the pump on a firm, level surface.
- Position it as close to the water source as practical.
- Keep the suction pipe short and direct.
- Use appropriate 1" pipework.
- Ensure all suction joints are airtight.
- Minimize bends and restrictions.
- Use a suitable foot valve/check valve where required.
- Ensure sufficient water is available before starting.
- Avoid prolonged dry operation.
- Provide adequate motor ventilation.
- Protect the pump from flooding and submersion.
- Install appropriate electrical protection and earthing.
- Clean suction filters regularly where sediment is present.
Performance Summary
| Performance Point | XKm50-1 |
|---|---|
| Maximum Flow | 25 L/min |
| Maximum Flow | 1.5 m³/h |
| Maximum Head | 22 m |
| At 5 L/min | 19 m head |
| At 10 L/min | 15 m head |
| At 15 L/min | 11 m head |
| At 20 L/min | 7 m head |
| At 25 L/min | 3 m head |
| Maximum Suction | 8 m |
The performance values above are based on the published XKm50-1 hydraulic data.
Product Description
LEO XKm50-1 0.11kW 0.15HP Peripheral Water Pump is a compact and efficient 220V single-phase peripheral pump designed for small domestic water supply, garden irrigation, sprinkler systems, water-pressure boosting and clean-water transfer. It provides up to 25 L/min flow, 22 m maximum head and 8 m maximum suction, with standard 1" × 1" inlet and outlet connections.
The pump features a brass impeller, AISI 304 stainless-steel shaft, anti-rust-treated HT200 cast-iron pump body, carbon/ceramic mechanical seal, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. These features make it suitable for compact domestic, garden and light-duty clean-water pumping applications.
With its 0.15 HP motor and compact peripheral design, the LEO XKm50-1 is a practical choice for small water systems where moderate flow, useful pressure and compact installation are required.
SEO Product Title
LEO XKm50-1 0.11kW 0.15HP 220V Peripheral Water Pump – 25L/min, 22m Head
Short Product Description
LEO XKm50-1 is a 0.11kW / 0.15HP 220V peripheral water pump designed for small domestic water supply, garden irrigation, sprinkler systems, water-pressure boosting and clean-water transfer. It provides up to 25 L/min flow, 22 m maximum head and 8 m maximum suction, with 1" × 1" connections. Features include a brass impeller, AISI 304 stainless-steel shaft, anti-rust-treated cast-iron pump body, copper winding, built-in thermal protection, Class F insulation and IPX4 protection.
Inquiry - LEO PERIPHERAL, SELF-PRIMING PERIPEHRAL PUMPS - XKM 50-1