The LEO APm37 is a compact 0.37 kW / 0.5 HP peripheral water pump designed for clean-water transfer, small domestic water supply, automatic sprinkler systems, garden irrigation and small air-conditioning/support applications. LEO's official APm documentation specifies a 220/240 V single-phase motor, 1" × 1" connections, 40 m maximum head, and 8 m maximum suction.
There is an important naming distinction for your catalogue: APm37 is LEO's standard Peripheral Pump, while APSm37 is the dedicated Self-Priming Peripheral Pump. Malaysian listings for APSM37 show 5–30 L/min, 35–5 m head and 9 m maximum suction, so these specifications should not be mixed with APm37.
Technical Specifications
| Specification | LEO APm37 |
|---|---|
| Brand | LEO |
| Model | APm37 |
| Pump Type | Peripheral Water Pump |
| Motor Power | 0.37 kW / 0.5 HP |
| Voltage | 220–240 V |
| Phase | Single Phase |
| Frequency | 50/60 Hz, depending on market version |
| Maximum Flow | Approx. 40 L/min |
| Maximum Capacity | Approx. 2.4 m³/h |
| Maximum Head | 40 m |
| Maximum Suction | 8 m |
| Inlet | 1" |
| Outlet | 1" |
| Impeller | Brass |
| Pump Body | HT200 Cast Iron |
| Pump Support | HT200 Cast Iron |
| Shaft | AISI 304 Stainless Steel |
| Mechanical Seal | Carbon / Ceramic |
| O-Ring | NBR |
| Motor Winding | Copper |
| Insulation Class | F |
| Protection Class | IPX4 |
| Thermal Protection | Built-In |
| Maximum Liquid Temperature | 40–60°C, depending on market specification |
| Maximum Ambient Temperature | 40°C |
| Pump Dimensions | Approx. 260 × 132 × 155 mm |
| Gross Weight | Approx. 5.5 kg |
LEO's European technical data lists APm37 at 0.37 kW, with a hydraulic curve reaching approximately 40 m head at zero flow and 40 L/min at low head, while the official APm37 documentation lists 2.4 m³/h maximum flow and 35 m maximum head in another market specification. This variation appears to reflect different regional technical tables/versions, so the nameplate or supplier datasheet for the actual stock should be used for the final specification.
0.37 kW / 0.5 HP Motor
The APm37 is equipped with a 0.37 kW / 0.5 HP single-phase motor. This power rating provides a useful balance between compact size, electrical consumption and water-pressure capability.
It is suitable for relatively small water systems where a larger 0.75 HP or 1 HP pump would be unnecessary.
Typical applications include:
- Domestic water supply
- Garden irrigation
- Small sprinkler systems
- Water transfer
- Water-pressure boosting
- Small agricultural applications
- Utility water systems
- Small air-conditioning support equipment
LEO specifically identifies the APm series for clean-water transfer, small living-water supply, automatic sprinklers and small air-conditioning/support equipment.
Peripheral Pump Hydraulic Design
The APm37 uses a peripheral hydraulic design. This type of pump is particularly useful when relatively high pressure is required from a compact pump with a comparatively small motor.
Compared with many conventional centrifugal pumps of similar motor size, a peripheral pump can provide useful head at relatively modest flow rates.
This makes the APm37 suitable for:
- Small domestic pressure systems
- Garden watering
- Small sprinkler systems
- Tank transfer
- Utility water supply
40 m Maximum Head
The APm37 is published with a maximum head of approximately 40 m in LEO's European technical data.
40 m water head is approximately equivalent to 3.9 bar of theoretical static pressure.
The maximum-head figure occurs at very low or zero flow. It should therefore not be interpreted as 40 m head being available simultaneously with the maximum flow.
For actual installation selection, the required duty point should be determined from:
Static head + pipe friction + fittings + required outlet pressure = Total Dynamic Head
Hydraulic Performance
LEO's published APm37 performance data gives approximately the following relationship:
| Flow | Approx. Head |
|---|---|
| 0 L/min | 40 m |
| 5 L/min | 35 m |
| 10 L/min | 30 m |
| 15 L/min | 25 m |
| 20 L/min | 20 m |
| 25 L/min | 15 m |
| 30 L/min | 10 m |
| 35 L/min | 5 m |
| 40 L/min | 0 m |
The exact operating point depends on the connected pipe system.
This table is useful for website customers because it demonstrates why maximum flow and maximum head should not be treated as simultaneous operating values.
8 m Maximum Suction
The APm37 is specified with a maximum suction of 8 m.
This allows the pump to be installed above a suitable water source within the stated suction limit, provided the suction pipe is correctly installed.
Potential water sources include:
- Storage tanks
- Rainwater tanks
- Reservoirs
- Shallow wells
- Water collection tanks
For reliable suction performance, the suction pipe should be:
- Properly sealed
- As short as practical
- Appropriately sized
- Free from air leaks
- Installed with suitable suction-side fittings
Brass Impeller
The APm37 uses a brass impeller.
The impeller is the primary hydraulic component responsible for converting motor rotation into water pressure and flow.
Brass provides good mechanical durability and corrosion resistance for normal clean-water applications.
HT200 Cast-Iron Pump Body
The pump body is manufactured from HT200 cast iron and receives special anti-rust treatment.
This construction provides a robust housing for the hydraulic components and is suitable for normal indoor and sheltered outdoor installations.
AISI 304 Stainless-Steel Shaft
The APm37 incorporates an AISI 304 stainless-steel shaft.
The shaft transfers the motor's rotational energy to the brass impeller.
AISI 304 provides good corrosion resistance in normal clean-water service and is suitable for the pump's intended applications.
Carbon/Ceramic Mechanical Seal
The mechanical seal is manufactured using a carbon/ceramic combination.
The seal prevents water from travelling along the rotating shaft toward the motor assembly.
Correct pump installation and operation within the specified temperature and pressure limits are important for mechanical-seal service life.
Copper Motor Winding
The APm37 uses copper motor winding.
Copper provides good electrical conductivity and supports reliable motor operation.
The motor should be connected to the correct supply voltage with suitable circuit protection and proper earthing.
Built-In Thermal Protector
The single-phase motor includes a built-in thermal protector.
This helps protect the motor from excessive temperature resulting from abnormal operating conditions.
Potential causes of overheating include:
- Excessive motor load
- Mechanical obstruction
- Incorrect voltage
- Poor ventilation
- Excessive ambient temperature
- Prolonged abnormal operation
Thermal protection does not replace proper electrical circuit protection.
Class F Insulation
The motor is specified with Class F insulation.
This provides appropriate thermal resistance for the intended operating conditions.
IPX4 Protection
The APm37 has an IPX4 protection rating.
This protects the motor against water splashing from different directions.
It should still be protected from:
- Flooding
- Submersion
- Standing water
- High-pressure water jets
- Severe weather exposure
1" × 1" Pipe Connections
The pump has 1-inch inlet and 1-inch outlet connections.
These connections are convenient for common household, garden and irrigation pipework.
For optimum hydraulic performance:
- Avoid unnecessary pipe reductions.
- Keep suction piping short.
- Minimize sharp bends.
- Use suitable valves and fittings.
- Ensure suction connections are airtight.
- Clean suction filters regularly.
Domestic Water Supply
The APm37 is suitable for small domestic water-supply applications where the required flow and pressure fall within its performance curve.
Potential applications include:
- Household utility water
- Water tank supply
- Outdoor taps
- Garden taps
- Small pressure-boosting systems
- Water transfer
For multi-outlet systems, pump selection should account for simultaneous water demand.
Garden Irrigation
The APm37 is suitable for small-scale garden irrigation.
Applications include:
- Garden hoses
- Small sprinklers
- Flower beds
- Vegetable gardens
- Landscape irrigation
- Greenhouse watering
The 0.5 HP motor provides a practical solution for small irrigation systems without the electrical consumption of a larger pump.
Automatic Sprinkler Systems
LEO identifies the APm series as suitable for automatic water sprinkler systems.
The APm37 can therefore be incorporated into a small sprinkler installation where the required pressure and flow match its hydraulic performance.
Water Tank Transfer
The APm37 can be used for clean-water transfer between storage tanks or from a water source to a distribution system.
Typical arrangement:
Water tank → APm37 → Distribution pipe → Water outlets
For elevated transfer, calculate the total vertical lift and pipe friction before selecting the pump.
Small Air-Conditioning Applications
LEO also lists small air-conditioning systems or supporting equipment as potential applications for the APm series.
For HVAC-related applications, verify:
- Required flow
- Required head
- Liquid temperature
- Fluid compatibility
- Operating cycle
before installation.
Clean-Water Applications
The APm37 is intended for clean water or liquids with physical and chemical properties similar to water.
Suitable liquids include:
- Fresh water
- Clean storage-tank water
- Filtered rainwater
- Clean irrigation water
- Utility water
It should not be selected for:
- Sewage
- Sludge
- Mud
- Heavy sediment
- Abrasive slurry
- Fibrous wastewater
- Liquids containing large solids
If the water contains suspended particles, suitable filtration should be installed upstream.
Compact Construction
The APm37 has published dimensions of approximately 260 × 132 × 155 mm, with a gross weight of approximately 5.5 kg.
Its compact dimensions make it suitable for installations where space is limited.
Typical locations include:
- Small pump rooms
- Utility areas
- Garden pump installations
- Water-tank areas
- Residential service areas
- Small irrigation systems
APm37 vs APSm37
Because your supplied product category includes both "Peripheral" and "Self-Priming Peripheral," the distinction is important:
| Specification | APm37 | APSm37 |
|---|---|---|
| Pump Type | Peripheral | Self-Priming Peripheral |
| Motor | 0.37 kW / 0.5 HP | 0.37 kW / 0.5 HP |
| Max Head | 40 m | 35 m |
| Published Flow | Up to 40 L/min | 5–30 L/min |
| Max Suction | 8 m | Approx. 9 m in Malaysian listing |
| Connections | 1" × 1" | 1" × 1" |
| Impeller | Brass | Brass |
| Main Difference | Standard peripheral design | Self-priming hydraulic design |
LEO separately identifies APm as its Peripheral Pump series and APSm as its Self-Priming Peripheral Pump series.
Therefore, if your physical product label says APm37, the recommended catalogue title should retain APm37 Peripheral Pump. If the label says APSm37, use APSm37 Self-Priming Peripheral Pump.
Main Applications
The LEO APm37 is suitable for:
- Small domestic water supply
- Garden irrigation
- Small sprinkler systems
- Water tank transfer
- Small water-pressure boosting
- Rainwater distribution
- Small agricultural irrigation
- Landscape watering
- Utility water transfer
- Small air-conditioning support systems
- General clean-water pumping
Key Advantages
The LEO APm37 offers:
- 0.37 kW / 0.5 HP motor
- Single-phase operation
- Up to 40 L/min flow
- Up to 40 m head
- 8 m maximum suction
- 1" × 1" connections
- Brass impeller
- AISI 304 stainless-steel shaft
- Anti-rust-treated HT200 cast-iron body
- Carbon/ceramic mechanical seal
- NBR O-ring
- Copper motor winding
- Built-in thermal protection
- Class F insulation
- IPX4 protection
- Compact construction
- Low electrical power requirement
- Suitable for clean-water applications
Installation Recommendations
For reliable operation:
- Install the pump on a firm, level base.
- Position it as close to the water source as practical.
- Keep the suction pipe short and direct.
- Use suitable 1" pipework.
- Ensure all suction connections are airtight.
- Minimize bends and restrictions.
- Install a suitable foot valve/check valve where required.
- Ensure adequate water is available before starting.
- Avoid prolonged dry running.
- Provide adequate ventilation around the motor.
- Protect the pump from flooding and submersion.
- Install appropriate electrical protection and earthing.
- Clean suction filters regularly.
Important Product Selection Note
For your website catalogue, I would recommend listing this model as:
LEO APm37 PERIPHERAL WATER PUMP – 0.37kW / 0.5HP
rather than combining APm37 and APSm37 specifications. LEO's official documentation clearly separates APm Peripheral Pumps from APSm Self-Priming Peripheral Pumps.
Product Description
LEO APm37 0.37kW / 0.5HP Peripheral Water Pump is a compact and durable 220–240V single-phase peripheral pump designed for small domestic water supply, garden irrigation, automatic sprinkler systems, water tank transfer and general clean-water applications. The pump delivers up to approximately 40 L/min flow and 40 m maximum head, with 1" × 1" inlet and outlet connections and an 8 m maximum suction capability.
The APm37 features a brass impeller, AISI 304 stainless-steel shaft, HT200 cast-iron pump body with anti-rust treatment, carbon/ceramic mechanical seal, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. Its compact approximately 5.5 kg construction makes it suitable for residential, garden, utility and small irrigation installations.
SEO Product Title
LEO APm37 0.37kW 0.5HP 220V Peripheral Water Pump – 40m Head, 40L/min
Short Product Description
LEO APm37 is a 0.37kW / 0.5HP peripheral water pump designed for domestic water supply, garden irrigation, sprinkler systems, water tank transfer and clean-water applications. It provides up to 40 L/min flow, 40 m maximum head and 8 m maximum suction, with standard 1" × 1" connections. The pump features a brass impeller, AISI 304 stainless-steel shaft, anti-rust-treated HT200 cast-iron body, carbon/ceramic mechanical seal, copper winding, built-in thermal protection, Class F insulation and IPX4 protection.
Inquiry - LEO PERIPHERAL, SELF-PRIMING PERIPEHRAL PUMPS - APM 37