The LEO APSm37 is a compact self-priming peripheral water pump designed for clean-water transfer, small domestic water supply, automatic sprinkler systems, small irrigation applications and small air-conditioning/support equipment. LEO classifies the APSm series specifically as a Self-Priming Peripheral Pump, distinguishing it from the standard APm peripheral-pump range.
For the Malaysian APSm37 220V version, published specifications identify a 0.37 kW / 0.5 HP single-phase motor, 5–30 L/min flow, 35–5 m head, 9 m maximum suction, and 1" × 1" inlet/outlet connections.
Technical Specifications
| Specification | LEO APSm37 |
|---|---|
| Brand | LEO |
| Model | APSm37 |
| Pump Type | Self-Priming Peripheral Pump |
| Motor Power | 0.37 kW / 0.5 HP |
| Voltage | 220 V |
| Phase | Single Phase |
| Frequency | 50 Hz |
| Maximum Flow | 30 L/min |
| Flow Range | 5–30 L/min |
| Maximum Head | 35 m |
| Head Range | 35–5 m |
| Maximum Suction | 9 m |
| Inlet | 1" |
| Outlet | 1" |
| Impeller | Brass |
| Pump Body | Cast Iron / Brass hydraulic components, depending on version |
| Shaft | AISI 304 Stainless Steel |
| Motor Winding | Copper |
| Mechanical Seal | Carbon / Ceramic |
| O-Ring | NBR |
| Insulation Class | F |
| Protection Class | IPX4 |
| Motor Protection | Thermal Protection |
| Suitable Liquid | Clean Water / Similar Liquids |
| Maximum Suction | 9 m |
| Application | Domestic, Irrigation, Sprinkler & Utility Water |
The Malaysian product listing confirms the key APSm37 specifications of 0.37 kW / 0.5 HP, 220 V, 5–30 L/min, 35–5 m head, 9 m suction and 1" × 1" connections. A Malaysian LEO catalogue also lists APSM37 at 0.37 kW, 220 V, 35–5 m head and 8 m maximum suction, so the suction specification can vary by regional documentation; for a website listing, the nameplate/supplied datasheet should take precedence.
0.37 kW / 0.5 HP Motor
The APSm37 is powered by a 0.37 kW / 0.5 HP single-phase motor.
This motor size provides a useful balance between power consumption, pressure capability and compact pump dimensions. It is particularly suitable for small water systems where a high-flow centrifugal pump is unnecessary.
Typical applications include:
- Small household water supply
- Garden irrigation
- Automatic sprinklers
- Water tank transfer
- Small pressure-boosting systems
- Shallow-well water supply
- Utility water transfer
- Small air-conditioning support systems
LEO specifically identifies the APSm series for clean-water transfer, small domestic water supply, automatic sprinkler systems and small air-conditioning/support equipment.
Self-Priming Peripheral Design
The APSm designation identifies this as a self-priming peripheral pump. LEO places APSm under its self-priming peripheral-pump category.
The self-priming configuration is useful where the pump is installed above the water source and must draw water through a suction pipe.
The peripheral hydraulic design provides relatively high pressure from a compact 0.5 HP motor, making the APSm37 suitable for applications requiring moderate water flow and useful pressure.
30 L/min Maximum Flow
The APSm37 has a published maximum flow of approximately 30 L/min, equivalent to approximately 1.8 m³/h.
The actual flow depends on the total system resistance.
As the required head increases, the available flow decreases. Therefore, 30 L/min should be treated as the maximum capacity rather than the flow available at maximum head.
The published operating range is approximately:
5–30 L/min
35 m Maximum Head
The APSm37 is specified with a maximum head of approximately 35 m, with the published operating range shown as 35–5 m.
A 35 m water head corresponds to approximately 3.43 bar of theoretical static pressure.
The maximum-head point occurs at very low flow. At higher flow rates, the available head decreases.
For pump selection, the actual duty point should be calculated from:
Static Head + Friction Loss + Fitting Losses + Required Outlet Pressure = Total Dynamic Head
Hydraulic Performance
The APSm37 is published with a performance range of approximately 5–30 L/min and 35–5 m head.
A simplified representation of the pump's operating range is:
| Flow | Approximate Head |
|---|---|
| 5 L/min | 35 m |
| 10 L/min | Approx. 30 m |
| 15 L/min | Approx. 25 m |
| 20 L/min | Approx. 18–20 m |
| 25 L/min | Approx. 10–12 m |
| 30 L/min | Approx. 5 m |
These intermediate values should be treated as indicative rather than exact duty-point data; the manufacturer's actual performance curve should be used for engineering selection.
9 m Maximum Suction
The APSm37 is commonly listed with a 9 m maximum suction in Malaysian product specifications.
Some LEO catalogue documentation lists 8 m for APSM37, so this is one specification that should be verified against the exact regional version supplied.
In practical installation, the achievable suction lift can be affected by:
- Suction-pipe length
- Pipe diameter
- Number of elbows
- Foot-valve restriction
- Air leakage
- Water temperature
- Atmospheric pressure
- Installation elevation
The suction pipe should therefore be kept as short and direct as practical.
Brass Impeller
The APSm series uses a brass hydraulic impeller. The brass construction provides good mechanical durability and corrosion resistance for normal clean-water pumping.
The impeller converts the mechanical energy from the motor into hydraulic energy, producing the required water pressure and flow.
AISI 304 Stainless-Steel Shaft
The pump incorporates an AISI 304 stainless-steel shaft, providing corrosion resistance in normal clean-water applications.
The shaft transfers rotational power from the motor to the peripheral impeller.
This construction is appropriate for:
- Domestic water
- Garden water
- Irrigation water
- Clean storage-tank water
- General utility water
Carbon/Ceramic Mechanical Seal
The APSm37 uses a carbon/ceramic mechanical sealing arrangement.
The mechanical seal prevents water from travelling along the rotating shaft into the motor assembly.
Correct installation, adequate water supply and operation within the specified temperature and pressure limits are important for maintaining seal life.
Copper Motor Winding
The motor is equipped with copper winding, providing good electrical conductivity and reliable motor operation.
The pump should be connected to the specified 220 V single-phase supply through suitable electrical protection and proper earthing.
Thermal Motor Protection
The motor incorporates thermal protection to help prevent damage caused by excessive temperature.
Potential causes of overheating include:
- Motor overload
- Mechanical blockage
- Incorrect supply voltage
- Poor ventilation
- Excessive ambient temperature
- Abnormal operating conditions
Thermal protection should not be considered a substitute for proper electrical circuit protection.
Class F Insulation
The motor is specified with Class F insulation, providing suitable thermal resistance for the pump's intended operating conditions.
This is particularly useful for a pump that may operate for extended periods during irrigation or domestic water-supply applications.
IPX4 Protection
The APSm series is specified with IPX4 protection in LEO documentation.
This provides protection against water splashing from different directions.
The pump should nevertheless be installed in a suitable protected location and should not be:
- Submerged
- Installed in standing water
- Exposed to continuous high-pressure spray
- Installed where flooding is likely
1" × 1" Connections
The APSm37 uses 1-inch inlet and 1-inch outlet connections.
These connections are suitable for common domestic and garden plumbing systems.
For optimum suction performance:
- Use appropriately sized suction piping.
- Minimize unnecessary bends.
- Avoid excessive pipe reductions.
- Ensure all joints are airtight.
- Use a suitable foot valve where required.
- Keep the suction line as short as practical.
Domestic Water Supply
The APSm37 is suitable for small domestic water-supply systems.
Potential applications include:
- Household water transfer
- Outdoor taps
- Kitchen utility supply
- Bathroom water supply
- Small water tanks
- Residential pressure boosting
The pump should be selected according to the required simultaneous flow and total system head.
Garden Irrigation
The APSm37 is suitable for small garden irrigation systems.
Typical applications include:
- Garden hoses
- Small sprinklers
- Flower beds
- Vegetable gardens
- Landscape watering
- Greenhouse irrigation
Its 0.5 HP motor provides useful pressure without requiring a larger pump for relatively small irrigation systems.
Automatic Sprinkler Systems
LEO specifically identifies automatic water sprinkler systems as an application for the APSm series.
The pump can be used where the sprinkler system's required pressure and flow fall within the APSm37 performance curve.
Before installation, verify:
- Number of sprinklers operating simultaneously
- Required sprinkler pressure
- Pipe diameter
- Total pipe length
- Elevation difference
- Valve and fitting losses
Water Tank Transfer
The APSm37 can be used for clean-water transfer from storage tanks to household or garden distribution systems.
Typical configuration:
Water Tank → Foot Valve → Suction Pipe → APSm37 → Distribution Pipe → Water Outlets
The self-priming design and published suction capability make it suitable for certain above-water-level pump installations.
Shallow-Well Water Supply
The APSm37 can also be considered for shallow-well applications, provided the actual suction lift remains within the pump's capability.
A properly installed suction line is critical. Air entering the suction line can prevent successful priming and cause unstable operation.
For deeper wells, a dedicated deep-well or submersible pump should normally be considered instead.
Clean-Water Applications
LEO states that APSm pumps are designed to transfer clean water or other liquids with physical and chemical properties similar to water.
Suitable applications include:
- Fresh water
- Clean tank water
- Filtered rainwater
- Clean irrigation water
- Utility water
The pump should not be used for:
- Sewage
- Sludge
- Mud
- Abrasive slurry
- Fibrous wastewater
- Heavy sediment
- Liquids containing large solids
Where water contains suspended particles, a suitable upstream filter should be considered.
Compact Domestic Pump
The APSm37 is designed as a compact pump for small-scale water applications.
It is particularly useful where the customer needs:
- Self-priming capability
- Moderate water flow
- Useful pressure
- Compact installation
- Simple plumbing
- Clean-water pumping
APSm37 vs APm37
This distinction is useful when cataloguing your LEO products.
| Specification | APSm37 | APm37 |
|---|---|---|
| Pump Type | Self-Priming Peripheral | Peripheral |
| Motor Power | 0.37 kW / 0.5 HP | 0.37 kW / 0.5 HP |
| Maximum Flow | 30 L/min | Higher depending on version |
| Maximum Head | 35 m | Approx. 40 m depending on version |
| Maximum Suction | 8–9 m depending on documentation | Approx. 8 m |
| Self-Priming | Yes | No dedicated self-priming design |
| Connections | 1" × 1" | 1" × 1" |
| Main Application | Domestic / garden / sprinkler | General water pumping |
LEO's product classification confirms that APSm is the self-priming peripheral range, while APm is the conventional peripheral range.
Main Applications
The LEO APSm37 is suitable for:
- Small domestic water supply
- Garden irrigation
- Automatic sprinkler systems
- Water tank transfer
- Shallow-well water supply
- Household water pressure boosting
- Rainwater distribution
- Small agricultural irrigation
- Landscape watering
- Utility water transfer
- Small air-conditioning systems
- General clean-water pumping
Key Advantages
The LEO APSm37 offers:
- 0.37 kW / 0.5 HP motor
- 220 V single-phase operation
- 5–30 L/min flow range
- 35–5 m head range
- 8–9 m maximum suction, depending on regional specification
- Self-priming peripheral design
- 1" × 1" connections
- Brass impeller
- AISI 304 stainless-steel shaft
- Carbon/ceramic mechanical seal
- Copper motor winding
- Thermal motor protection
- Class F insulation
- IPX4 protection
- Compact construction
- Suitable for clean-water pumping
Installation Recommendations
For reliable operation:
- Install the pump on a firm, level surface.
- Position it as close to the water source as practical.
- Keep the suction line short and direct.
- Make all suction joints completely airtight.
- Use a suitable foot valve/check valve where required.
- Avoid excessive suction-side bends.
- Avoid undersized suction piping.
- Ensure adequate water is available before operation.
- Avoid prolonged dry running.
- Provide adequate ventilation around the motor.
- Protect the pump from flooding and submersion.
- Install suitable electrical protection and earthing.
- Clean the suction filter regularly.
- Check connections and seals periodically.
Important Specification Note for Your Catalogue
For the Malaysian market, I would list the APSm37 primarily as:
LEO APSm37 0.37kW / 0.5HP 220V Self-Priming Peripheral Pump
with:
Flow: 5–30 L/min
Head: 35–5 m
Maximum Suction: 9 m
Inlet/Outlet: 1" × 1"
However, because one LEO catalogue lists the maximum suction as 8 m, the safest practice is to verify the actual stock's nameplate/datasheet before publishing 9 m as a fixed specification.
Product Description
LEO APSm37 0.37kW / 0.5HP Self-Priming Peripheral Water Pump is a compact and durable 220V single-phase self-priming peripheral pump designed for small domestic water supply, garden irrigation, automatic sprinkler systems, shallow-well applications and clean-water transfer. It provides a published flow range of 5–30 L/min and head range of approximately 35–5 m, with 1" × 1" inlet and outlet connections.
The APSm37 features a brass impeller, AISI 304 stainless-steel shaft, carbon/ceramic mechanical seal, copper motor winding, thermal protection, Class F insulation and IPX4 protection. Its self-priming peripheral design makes it particularly suitable for applications where the pump is installed above the water source and reliable water suction is required.
With its 0.5 HP motor, compact construction and useful pressure capability, the LEO APSm37 is a practical choice for residential, garden, irrigation and light-duty water-supply systems.
SEO Product Title
LEO APSm37 0.37kW 0.5HP 220V Self-Priming Peripheral Water Pump – 30L/min, 35m Head
Short Product Description
LEO APSm37 is a 0.37kW / 0.5HP 220V self-priming peripheral water pump designed for domestic water supply, garden irrigation, automatic sprinkler systems, shallow-well applications and clean-water transfer. It delivers 5–30 L/min flow, up to 35 m head and approximately 8–9 m maximum suction depending on the regional specification, with 1" × 1" connections. It features a brass impeller, AISI 304 stainless-steel shaft, carbon/ceramic mechanical seal, copper winding, thermal protection, Class F insulation and IPX4 protection.
Inquiry - LEO PERIPHERAL, SELF-PRIMING PERIPEHRAL PUMPS - APSM 37