The LEO XKSM 155A is a compact self-priming peripheral water pump designed for domestic water supply, water transfer, small sprinkler systems and light-duty pressure applications. It is the higher-powered model compared with the XKSM 115A and XKSM 125, with a rated motor output of 0.155 kW (155 W / 0.20 HP).
For the XKSM 155A specifically, Malaysian product specifications list a 2.5–30 L/min flow range, 32–2.5 m head range, 8 m maximum suction lift, 1" × 1" connections and 220 V supply.
LEO's official documentation describes the corresponding self-priming peripheral pump family as suitable for transferring clean water or liquids with physical and chemical properties similar to water, including small domestic water supply, automatic sprinkler systems, small air-conditioning systems and supporting equipment.
Product Specifications
| Specification | LEO XKSM 155A |
|---|---|
| Brand | LEO |
| Model | XKSM 155A |
| Product Type | Self-Priming Peripheral Pump |
| Pump Type | Peripheral / Regenerative |
| Rated Power | 0.155 kW |
| Motor Power | 155 W |
| Horsepower | 0.20 HP |
| Voltage | 220 V |
| Phase | Single Phase |
| Flow Range | 2.5–30 L/min |
| Maximum Flow | 30 L/min |
| Head Range | 32–2.5 m |
| Maximum Head | 32 m |
| Maximum Suction Lift | 8 m |
| Suction Connection | 1" |
| Discharge Connection | 1" |
| Pump Configuration | Self-Priming |
| Application Fluid | Clean Water |
| Installation | Surface Mounted |
| Primary Application | Domestic / Light-Duty Water Supply |
The published XKSM specification confirms 0.155 kW / 0.20 HP, 2.5–30 L/min, 32–2.5 m head, 8 m maximum suction and 1" × 1" 220 V connections.
Product Overview
The XKSM 155A is designed for applications where a relatively compact pump is required to provide useful water pressure. Its peripheral impeller allows the pump to develop a comparatively high head for its small motor size.
The model's maximum head of 32 metres makes it particularly useful for small domestic installations involving vertical lifting or pressure requirements. However, the maximum head and maximum flow are not achieved simultaneously. At higher flow rates, the available head decreases according to the pump's hydraulic performance curve.
The self-priming configuration also makes the XKSM 155A suitable for installations where the pump must draw water from a lower-level source, subject to correct installation and the specified 8 m maximum suction lift.
Key Features
Self-Priming Design
The XKSM 155A is designed to operate as a self-priming peripheral pump. This is useful when the pump is positioned above a water source and must draw water through a suction pipe. Correct priming and an airtight suction line are essential for reliable operation.
0.20 HP Compact Motor
The pump uses a 0.155 kW / 0.20 HP motor, providing a compact solution for small water-supply and pressure applications. It is intended for relatively modest water demand rather than high-volume industrial pumping.
Maximum 32 m Head
The XKSM 155A provides a maximum head of approximately 32 m, giving it a higher pressure capability than the XKSM 115A and XKSM 125 models. This makes it useful where the installation requires additional delivery height or pressure.
Flow Up to 30 L/min
The published flow range is approximately 2.5–30 L/min. Actual flow depends on the operating head, pipe diameter, pipe length, fittings, suction conditions and other hydraulic losses.
1" × 1" Connections
The pump has 1-inch suction and discharge connections, making it compatible with common small domestic water-piping systems.
8 m Maximum Suction
The published maximum suction lift is 8 m. This should be regarded as a maximum specification rather than a guaranteed operating condition for every installation. Actual suction performance can be affected by pipe losses, air leakage, water temperature, atmospheric pressure and installation elevation.
Pump Performance
The XKSM 155A has the following published hydraulic range:
- Maximum head: 32 m
- Maximum flow: 30 L/min
- Minimum stated flow: approximately 2.5 L/min
- Head at the upper flow end: approximately 2.5 m
- Maximum suction: 8 m
The relationship between flow and head is important when selecting this pump. At or near the 32 m maximum head, flow will be very low. Conversely, near the 30 L/min maximum flow, available head is only around the lower end of the specified curve.
For a practical installation, the required operating point should therefore be calculated from the combination of:
Static head + friction losses + required outlet pressure = total dynamic head.
The pump should be selected so that the actual system duty point falls within its useful performance range.
Recommended Applications
The LEO XKSM 155A is suitable for:
- Domestic water supply
- Small household water systems
- Water transfer from storage tanks
- Small overhead tank filling
- Garden watering
- Small irrigation systems
- Automatic sprinkler systems
- Small water pressure applications
- Small wash-down systems
- Small air-conditioning water systems
- General clean-water transfer
- Supporting equipment requiring a compact pressure pump
LEO specifies its self-priming peripheral pump family for small domestic water supply, automatic sprinkler systems, small air-conditioning systems and supporting equipment.
Suitable Water Sources
The XKSM 155A can be used for suitable clean-water sources such as:
- Storage tanks
- Water reservoirs
- Domestic water tanks
- Rainwater storage systems, where the water is adequately filtered
- Suitable wells or tanks within the specified suction conditions
- Other clean-water sources
The suction system must be properly sealed. Any significant air leakage can prevent the pump from maintaining prime and can cause poor or intermittent performance.
Suitable Fluids
The XKSM 155A is intended primarily for clean water and liquids with physical and chemical characteristics similar to water. This is consistent with LEO's stated application for its self-priming peripheral pump family.
It is generally not appropriate for:
- Sewage
- Muddy water
- Abrasive slurry
- Water containing large quantities of suspended solids
- Highly corrosive chemicals
- Flammable liquids
- Liquids outside the manufacturer's approved temperature and chemical limits
For contaminated water, wastewater or abrasive fluids, a pump specifically designed for those media should be selected.
Installation Considerations
For reliable operation, the suction line should be:
- Properly sealed against air leakage
- As short and straight as practical
- Appropriately sized
- Free from unnecessary bends and restrictions
- Properly supported
A foot valve or suitable check valve may be required depending on the installation to prevent the suction line from draining when the pump stops.
The pump should be installed on a firm and level base. Before initial operation, the pump should be correctly filled/primed according to the manufacturer's instructions. Do not operate the pump dry, as this can damage the mechanical seal and other internal components.
XKSM 155A Compared with XKSM 115A and XKSM 125
| Model | Power | Flow | Maximum Head | Max. Suction | Connection |
|---|---|---|---|---|---|
| XKSM 115A | 0.115 kW / 0.15 HP | 2.5–30 L/min | 25 m | 8 m | 3/4" × 3/4" |
| XKSM 125 | 0.125 kW / 0.17 HP | 5–30 L/min | 25 m | 8 m | 1" × 1" |
| XKSM 155A | 0.155 kW / 0.20 HP | 2.5–30 L/min | 32 m | 8 m | 1" × 1" |
These model-specific figures are published in the Malaysian XKSM product listing.
The XKSM 155A is therefore the stronger choice of these three models when the application requires higher pressure/head, while the XKSM 115A and XKSM 125 are more appropriate for lower-head applications.
Main Advantages
- 0.20 HP motor provides more power than the smaller XKSM models.
- 32 m maximum head provides useful pressure for small domestic systems.
- Up to 30 L/min flow for light-duty water transfer.
- Self-priming design for suitable suction applications.
- 8 m maximum suction lift for appropriately designed suction systems.
- 1" × 1" connections provide compatibility with common domestic plumbing.
- Compact peripheral design provides high head relative to motor size.
- 220 V single-phase operation is suitable for typical residential electrical supplies.
- Suitable for clean-water applications such as domestic supply and small irrigation.
- Compact construction makes it practical for installations where space is limited.
Website Product Description
LEO XKSM 155A 0.20HP Self-Priming Peripheral Water Pump is a compact and reliable pump designed for domestic water supply, water transfer, pressure boosting, garden watering and other light-duty clean-water applications. Powered by a 0.155 kW / 0.20 HP motor, the XKSM 155A provides a flow range of approximately 2.5–30 L/min and a maximum head of 32 metres, making it suitable for applications requiring useful water pressure from a compact pump.
The XKSM 155A features a self-priming peripheral pump design with a maximum suction lift of 8 metres, allowing it to draw water from a suitable lower-level source when correctly installed and primed. Its 1-inch suction and 1-inch discharge connections make it suitable for standard small domestic water-piping systems.
The peripheral pumping design enables the pump to generate relatively high pressure for its compact motor size. This makes the LEO XKSM 155A suitable for small household water systems, storage-tank transfer, automatic sprinkler systems, garden watering, small irrigation systems and other clean-water applications. LEO specifies its self-priming peripheral pump range for clean water and liquids with similar physical and chemical properties.
SEO Product Title
LEO XKSM 155A 0.20HP Self-Priming Peripheral Water Pump 220V 1" × 1"
SEO Meta Description
LEO XKSM 155A 0.20HP self-priming peripheral water pump with 32m maximum head, 30L/min flow and 8m suction lift. Ideal for domestic water supply, tank transfer, irrigation and sprinkler systems.
Inquiry - LEO PERIPHERAL, SELF-PRIMING PERIPEHRAL PUMPS - XKSM 155A