The LEO XSP 32-17/1.5I is a heavy-duty 2 HP / 1.5 kW sewage submersible pump designed for high-volume wastewater and sewage drainage. It is suitable for factories, construction sites, commercial facilities, municipal sewage systems, residential drainage stations, agricultural drainage and other applications where wastewater containing suspended solids needs to be removed.
LEO's technical documentation identifies this model as XSP32-17/1.5I, with a 1.5 kW motor, 2 HP rating, 220 V / 50 Hz single-phase supply, 50 mm outlet, approximately 530 L/min maximum flow and 17 m maximum head.
Product Specifications
| Specification | Details |
|---|---|
| Brand | LEO |
| Model | XSP 32-17/1.5I |
| Pump Type | Sewage Submersible Pump |
| Motor Power | 1.5 kW |
| Motor Rating | 2 HP |
| Voltage | 220 V |
| Frequency | 50 Hz |
| Phase | Single Phase |
| Maximum Flow | Approx. 530 L/min |
| Maximum Flow | Approx. 31.8 m³/h |
| Maximum Head | 17 m |
| Outlet Diameter | 50 mm / 2" |
| Maximum Immersion Depth | 5 m |
| Maximum Liquid Temperature | 40°C |
| Permitted Liquid pH | 4–10 |
| Motor Winding | Copper |
| Motor Shaft | Stainless Steel Welded Shaft |
| Thermal Protection | Built-in |
| Insulation Class | B |
| Protection Class | IP68 |
| Mechanical Seal | Ceramic / Carbon |
| Construction | Stainless-Steel Submersible Sewage Pump |
| Installation | Fully Submersible |
The Malaysian listing for the equivalent LEO LSWM200XA confirms the same model designation XSP32-17/1.5I, with 1.5 kW / 2 HP power, 220 V supply, 2-inch outlet, approximately 533 L/min maximum flow and 17 m maximum head.
High-Volume Wastewater Pumping
The main advantage of the XSP 32-17/1.5I is its combination of high flow capacity and moderate lifting height. With a maximum flow of approximately 530–533 L/min, the pump can move close to 32 m³ of wastewater per hour under favourable hydraulic conditions.
The 17 m maximum head makes it appropriate for drainage systems where wastewater needs to be lifted from a sump, pit or collection tank to a discharge point at a moderate elevation.
The maximum flow and maximum head are not simultaneous operating points. Actual flow will decrease as the discharge head and pipe resistance increase. Pipe diameter, pipe length, elbows, valves and elevation should therefore be considered when sizing the system.
2 HP / 1.5 kW Motor
The pump is equipped with a 1.5 kW / 2 HP motor, providing considerably more pumping capacity than smaller domestic drainage pumps. The motor is designed for submerged operation and incorporates a copper winding for reliable electrical performance.
The built-in thermal protector provides additional protection against excessive motor temperature caused by overload or abnormal operating conditions.
50 mm / 2-Inch Discharge
The XSP32-17/1.5I uses a 50 mm / 2-inch discharge outlet. This relatively large discharge connection is appropriate for its high flow capacity and helps minimise excessive velocity and friction losses when correctly matched with the discharge pipe.
For best performance, the discharge pipe should be sized appropriately rather than using a substantially smaller hose simply because it is easier to install. An undersized discharge line can significantly reduce actual flow and increase system losses.
Sewage and Suspended-Solids Applications
Unlike a conventional clean-water pump, the XSP sewage series is designed specifically for wastewater and sewage drainage. Its construction and hydraulic arrangement are intended for liquids containing suspended matter.
Typical applications include:
- Factory wastewater drainage
- Construction-site drainage
- Commercial wastewater drainage
- Municipal sewage-treatment plants
- Residential sewage drainage stations
- Collection sump drainage
- Sewage holding tanks
- Agricultural drainage
- Farm wastewater removal
- Municipal drainage projects
- Methane-pool drainage
- Countryside field irrigation
These applications are consistent with the LEO XSP series documentation and Malaysian product listing.
IP68 Protection
The XSP32-17/1.5I uses an IP68-rated motor protection system, making it suitable for continuous submerged service when installed within the manufacturer's specified operating limits.
This is important for sewage pumps because the motor and electrical components are exposed to the surrounding wastewater during normal operation.
Thermal Protection
The motor incorporates a built-in thermal protector. If the motor temperature rises excessively because of overload or abnormal operating conditions, the protection system helps prevent thermal damage to the winding.
Correct electrical protection should still be provided at the installation level, including an appropriately rated circuit breaker and other protection required by local electrical standards.
Stainless-Steel Shaft and Mechanical Seal
The pump uses a stainless-steel welded shaft, while the mechanical seal is specified as ceramic/carbon. These components are important in a sewage pump because the pump operates in a wet and potentially corrosive environment.
The mechanical seal separates the pumped liquid from the motor assembly and is a critical component for preventing water ingress into the motor.
Operating Conditions
The published specifications indicate:
- Maximum immersion depth: 5 m
- Maximum liquid temperature: 40°C
- Liquid pH range: 4–10
- Maximum liquid density: approximately 1.2 × 10³ kg/m³
- Insulation class: B
- Protection class: IP68
These limits should be observed during installation and operation. The pump should not be used for liquids outside the specified temperature, chemical compatibility or operating range.
Automatic Drainage Operation
The XSP construction includes a float-switch arrangement in the documented assembly, allowing the pump to be configured for automatic water-level control.
In a typical sump installation, the float switch responds to changes in liquid level:
Water level rises → Float activates → Pump starts → Water level falls → Float deactivates → Pump stops
This arrangement is useful for wastewater pits and collection tanks because the pump does not need to be manually switched on and off each time the water level changes.
Recommended Installation
A typical installation can be arranged as:
Sewage / wastewater collection pit → LEO XSP32-17/1.5I → 2" discharge pipe → drainage point / treatment system
The pump should be installed in a suitable sump or collection area with adequate clearance around the inlet. The discharge pipe should be properly supported and sized for the required flow.
The pump should not be allowed to operate without sufficient liquid for cooling and pumping. Although the pump is designed for submerged operation, the specified 5 m maximum immersion depth should not be exceeded.
Important Selection Considerations
When selecting the XSP32-17/1.5I for a particular installation, calculate the total dynamic head (TDH) rather than using only the vertical height.
TDH consists broadly of:
Static lifting height + discharge pressure requirement + pipe friction losses + fitting/valve losses
For example, a system with a 10 m vertical lift does not necessarily operate at 10 m head because the discharge pipe and fittings also create hydraulic resistance.
The pump's approximately 530 L/min maximum-flow rating should likewise be treated as a maximum-flow figure rather than a guaranteed operating flow. The actual duty point must be established from the pump curve and system curve.
Main Product Advantages
- 2 HP / 1.5 kW motor for demanding wastewater applications.
- Approx. 530–533 L/min maximum flow for high-volume drainage.
- 17 m maximum head for moderate-height wastewater lifting.
- 2-inch / 50 mm outlet suitable for high-volume discharge.
- IP68 protection for submerged operation.
- Built-in thermal protection for additional motor safety.
- Copper motor winding for reliable operation.
- Stainless-steel welded shaft for improved corrosion resistance.
- Ceramic/carbon mechanical seal for reliable shaft sealing.
- 5 m maximum immersion depth for sump and sewage-pit installations.
- 40°C maximum liquid temperature for normal wastewater applications.
- Automatic float-switch arrangement for water-level-controlled operation.
- Suitable for industrial, commercial, municipal, residential and agricultural drainage.
Product Details Summary
The LEO XSP 32-17/1.5I is a 2 HP / 1.5 kW sewage submersible pump designed for high-volume wastewater and sewage drainage. It operates on 220 V / 50 Hz single-phase power and uses a 50 mm / 2-inch discharge outlet. With a maximum flow of approximately 530–533 L/min (around 31.8–32 m³/h) and a maximum head of 17 m, it is suitable for moving large quantities of wastewater from collection pits, sewage tanks and drainage stations. The pump features IP68 protection, built-in thermal protection, copper winding, a stainless-steel welded shaft and ceramic/carbon mechanical seal. It is suitable for factory wastewater, construction sites, commercial facilities, municipal sewage systems, residential drainage stations, agricultural drainage and other sewage applications.
SEO Product Title
LEO XSP 32-17/1.5I Sewage Submersible Pump 2HP 1.5kW – 530L/min, 17M Head
SEO Product Description
LEO XSP 32-17/1.5I Sewage Submersible Pump is a high-capacity 2HP / 1.5kW wastewater and sewage pump designed for demanding drainage applications. Operating at 220V/50Hz with a 2-inch / 50mm discharge outlet, it delivers a maximum flow of approximately 530–533 L/min (31.8–32 m³/h) and a maximum head of 17 metres. The pump features IP68 protection, built-in thermal protection, copper motor winding, stainless-steel welded shaft and ceramic/carbon mechanical seal for dependable submerged operation. With a maximum immersion depth of 5 metres and maximum liquid temperature of 40°C, the LEO XSP32-17/1.5I is suitable for factory wastewater drainage, construction sites, commercial facilities, municipal sewage-treatment systems, residential drainage stations, agricultural drainage and other high-volume wastewater applications.
Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - XSP 32-17/1.5I