The LEO XSP 16.2-22/1.5I is a 2 HP / 1.5 kW stainless-steel sewage submersible pump designed for pumping wastewater, dirty water, sewage and liquids containing suspended solids. It is a high-head sewage pump within the LEO XSP series, offering a maximum head of 22 m and a maximum flow of approximately 270 L/min (16.2 m³/h). LEO's technical documentation specifies the model with a 40 mm / 1½-inch discharge, 220 V / 50 Hz single-phase power supply and 1.5 kW motor.
Product Specifications
| Specification | Details |
|---|---|
| Brand | LEO |
| Model | XSP 16.2-22/1.5I |
| Pump Type | Stainless-Steel Sewage Submersible Pump |
| Motor Power | 1.5 kW |
| Motor Rating | 2 HP |
| Voltage | 220 V |
| Frequency | 50 Hz |
| Phase | Single Phase |
| Maximum Flow | 270 L/min |
| Maximum Flow | 16.2 m³/h |
| Maximum Head | 22 m |
| Discharge Outlet | 40 mm / 1½" |
| Maximum Immersion Depth | 5 m |
| Maximum Liquid Temperature | 40°C |
| Liquid pH Range | 4–10 |
| Maximum Liquid Density | 1.2 × 10³ kg/m³ |
| Protection Class | IP68 |
| Insulation Class | B |
| Motor Winding | Copper |
| Motor Shaft | Stainless-Steel Welded Shaft |
| Thermal Protection | Built-In |
| Installation | Fully Submersible |
| Float Switch | Available/automatic level-control configuration |
LEO's published technical material lists the XSP16.2-22/1.5I at 1.5 kW, 2 HP, 220 V/50 Hz, 270 L/min maximum flow and 22 m maximum head, with a 40 mm discharge. A Malaysian listing for the closely specified XSP16.2-22/1.5 series gives the operating range as 22–246 L/min and 21–3 m head, with a 40 mm outlet and 5 m maximum suction/immersion specification.
High-Head Sewage Pumping
The XSP 16.2-22/1.5I is particularly suitable where wastewater needs to be lifted to a relatively high discharge point.
Its 22 m maximum head is one of the key characteristics of this model. Compared with lower-head sewage pumps in the XSP range, it is better suited to installations involving greater vertical lift or higher discharge-system resistance.
The maximum-flow figure of 270 L/min / 16.2 m³/h should not be interpreted as the flow available at 22 m head. Actual flow decreases as system head increases. The pump's operating point is determined by the intersection of the pump curve and the system curve.
For product selection, consider:
Total Dynamic Head = Static Lift + Pipe Friction + Fitting Losses + Required Discharge Pressure
This is particularly important for long discharge pipelines.
2 HP / 1.5 kW Motor
The pump uses a 1.5 kW / 2 HP single-phase motor designed for submerged operation. The LEO XSP documentation identifies copper winding, a built-in thermal protector, Class B insulation and IP68 protection.
The built-in thermal protection helps protect the motor against excessive temperature caused by overload or abnormal operating conditions.
For permanent installations, appropriate external electrical protection should still be provided according to the applicable electrical requirements.
1½-Inch Discharge Outlet
The XSP16.2-22/1.5I is specified with a 40 mm / 1½-inch discharge outlet.
The smaller discharge compared with some higher-flow XSP models is consistent with this pump's higher-head design. Correct pipe sizing remains important because an undersized or excessively long discharge line can introduce significant friction losses and reduce actual pumping capacity.
Sewage and Dirty-Water Applications
The XSP series is designed for wastewater drainage and sewage applications, including liquids containing suspended particles. LEO documentation identifies applications such as factory wastewater drainage, construction sites, commercial facilities, municipal sewage-treatment systems, residential drainage stations, municipal projects and field irrigation.
The XSP16.2-22/1.5I is therefore appropriate for applications such as:
- Sewage drainage
- Wastewater drainage
- Dirty-water pumping
- Septic and sewage collection systems
- Drainage pits
- Sump pits
- Construction-site drainage
- Factory wastewater
- Commercial wastewater
- Residential sewage stations
- Municipal drainage
- Agricultural drainage
- Farm wastewater transfer
- Irrigation water containing suspended matter
A LEO product listing specifically describes the XSP16.2-22/1.5S configuration for sewage, sludge, dirty water and liquids containing impurities, with applications spanning agricultural, domestic, gardening, industrial, mining and construction environments.
Stainless-Steel Construction
The XSP series uses a stainless-steel construction suitable for submerged wastewater service. LEO's published specifications identify a stainless-steel welded shaft, while the motor uses copper winding and the pump incorporates a mechanical sealing arrangement to protect the motor from the pumped liquid.
The stainless-steel components provide improved resistance to corrosion compared with ordinary carbon-steel components and are particularly useful in wet drainage environments.
IP68 Protection
The pump has an IP68 protection rating, which is appropriate for a submersible sewage pump. The motor and electrical assembly are designed for submerged operation within the manufacturer's specified limits.
The pump should nevertheless be installed correctly, with the cable, electrical connections and discharge arrangement protected according to the installation requirements.
Built-In Thermal Protection
The built-in thermal protector provides additional protection against excessive motor temperature. This is useful in sewage applications because pumps may encounter increased hydraulic resistance, blockage or other abnormal operating conditions.
Thermal protection should be considered supplementary to proper system design. The discharge system should still be correctly sized, and the pump should not be operated outside its specified operating limits.
22-Metre Maximum Head
The 22 m maximum head makes the XSP16.2-22/1.5I particularly useful where the wastewater discharge point is significantly higher than the collection pit.
For example, it can be considered for:
- Deep drainage pits
- Sewage collection tanks
- Basement drainage
- Elevated discharge points
- Long discharge pipelines
- Wastewater transfer between different elevations
- Industrial drainage systems
The published operating range for one XSP16.2-22/1.5 listing is approximately 22–2 m head, with flow varying from approximately 30 to 250 L/min; another LEO listing gives a maximum of 270 L/min. This difference reflects different catalog/market configurations, so the manufacturer's specific pump curve should be used for final sizing.
Solids and Suspended Material
The XSP range is intended for wastewater containing suspended solids. However, it should not be treated as a general-purpose grinder pump.
Large objects, ropes, fibrous materials, stones and excessive abrasive solids can cause blockage or accelerated wear. Where the wastewater contains large debris, an appropriate screening or collection arrangement should be installed upstream of the pump.
Operating Conditions
The published XSP series operating conditions include:
- Maximum immersion depth: 5 m
- Maximum liquid temperature: 40°C
- Liquid pH: 4–10
- Maximum liquid density: approximately 1.2 × 10³ kg/m³
- Insulation class: B
- Protection class: IP68
These specifications should be observed when installing the pump.
The pump is intended for wastewater and dirty-water applications within the specified chemical and temperature range. Highly corrosive chemicals, oils or liquids outside the specified parameters require separate compatibility verification.
Automatic Level Control
The XSP sewage range is commonly supplied with a float switch for automatic water-level control. A Malaysian listing for the XSP16.2-22/1.5 series specifically identifies the model with a floating switch.
A float-switch installation can operate as follows:
Water level rises → Float switch activates → Pump starts → Water level falls → Float switch deactivates → Pump stops
This is useful for sump pits, sewage collection tanks and drainage stations where automatic water-level management is required.
Typical Installation
A typical system can be arranged as:
Sewage / wastewater pit → LEO XSP 16.2-22/1.5I → 1½" discharge line → drainage / treatment / collection point
The pump is placed inside the collection pit and completely submerged during normal operation. The discharge pipe carries wastewater from the pit to the desired discharge location.
The discharge line should be properly supported and should avoid unnecessary restrictions. Long horizontal pipe runs should be evaluated carefully because friction losses can substantially reduce the available flow.
Recommended Applications
The LEO XSP16.2-22/1.5I is well suited to:
Residential
- Septic tank drainage
- Sewage pits
- Basement wastewater
- Residential drainage stations
Commercial
- Commercial building drainage
- Wastewater collection tanks
- Restaurant or facility drainage systems
Industrial
- Factory wastewater
- Industrial drainage pits
- Process-water drainage where liquid compatibility is confirmed
Construction
- Construction-site drainage
- Excavation drainage
- Temporary wastewater removal
Agricultural
- Farm drainage
- Irrigation water transfer
- Dirty-water pumping
Municipal
- Sewage collection stations
- Drainage systems
- Municipal wastewater transfer
These uses align with the documented XSP application range.
Main Product Advantages
- 2 HP / 1.5 kW motor provides strong pumping performance.
- 22 m maximum head makes it suitable for higher-lift drainage.
- Up to 270 L/min flow provides substantial wastewater transfer capacity.
- 16.2 m³/h maximum flow class offers efficient high-volume drainage.
- 40 mm / 1½-inch outlet provides a compact discharge connection.
- IP68 protection is designed for submerged operation.
- Built-in thermal protection helps protect the motor from overheating.
- Copper motor winding supports reliable electrical performance.
- Stainless-steel welded shaft improves corrosion resistance.
- 5 m maximum immersion depth suits many drainage pits and sewage tanks.
- 40°C maximum liquid temperature accommodates typical wastewater conditions.
- Automatic float-switch operation is available for automatic drainage control.
- Suitable for domestic, commercial, industrial, construction, agricultural and municipal applications.
Product Details Summary
The LEO XSP 16.2-22/1.5I is a 2 HP / 1.5 kW stainless-steel sewage submersible pump designed for high-head wastewater and dirty-water drainage. Operating on 220 V / 50 Hz single-phase power, it provides a maximum flow of approximately 270 L/min (16.2 m³/h) and a maximum head of 22 m. It features a 40 mm / 1½-inch discharge outlet, IP68 protection, built-in thermal protection, copper motor winding and stainless-steel welded shaft. With a maximum immersion depth of 5 m and maximum liquid temperature of 40°C, the pump is suitable for sewage pits, wastewater tanks, construction-site drainage, factory wastewater, commercial facilities, residential drainage stations, municipal projects and agricultural applications.
SEO Product Title
LEO XSP 16.2-22/1.5I Sewage Submersible Pump 2HP 1.5kW – 270L/min, 22M Head
SEO Product Description
LEO XSP 16.2-22/1.5I Sewage Submersible Pump is a high-head 2HP / 1.5kW wastewater and sewage pump designed for reliable drainage of dirty water, sewage and liquids containing suspended solids. Operating at 220V/50Hz single-phase, this LEO submersible pump delivers up to 270L/min (16.2m³/h) with a maximum head of 22 metres and features a 40mm / 1½-inch discharge outlet. Built for demanding submerged applications, it incorporates IP68 protection, built-in thermal protection, copper motor winding and a stainless-steel welded shaft. The pump is suitable for residential sewage systems, drainage pits, construction sites, factories, commercial facilities, municipal wastewater systems, agricultural drainage and other high-head wastewater transfer applications.
Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - XSP 16.2-22/1.5I