The LEO LSWM 150XA is a heavy-duty automatic 1.5 HP / 1.1 kW sewage submersible pump designed for high-volume wastewater, sewage and dirty-water drainage. It is suitable for sewage collection pits, wastewater tanks, septic systems, construction sites, factories, commercial facilities, municipal sewage-treatment drainage and agricultural applications.
For the Malaysian LSWM150XA configuration, published specifications state 220 V single-phase operation, 1.1 kW / 1.5 HP motor power, maximum flow of 383 L/min, maximum head of 11.5 m and a 2-inch discharge outlet.
The model is listed as an XA automatic version with float-switch control and features a built-in thermal protector, AISI 304 fabricated shaft, handle and pump body, and Class F insulation.
Product Specifications
| Specification | Details |
|---|---|
| Brand | LEO |
| Model | LSWM 150XA |
| Pump Type | Automatic Sewage Submersible Pump |
| Impeller Type | Semi-Open / Wastewater Impeller Configuration* |
| Motor Power | 1.1 kW |
| Motor Rating | 1.5 HP |
| Voltage | 220 V |
| Frequency | 50 Hz |
| Phase | Single Phase |
| Maximum Flow | 383 L/min |
| Maximum Flow | Approx. 23.0 m³/h |
| Maximum Head | 11.5 m |
| Outlet Size | 2" |
| Automatic Control | Float Switch |
| Motor Protection | Built-In Thermal Protector |
| Insulation Class | F |
| Shaft Material | AISI 304 Stainless Steel |
| Pump Body | AISI 304 Stainless Steel* |
| Handle | AISI 304 Stainless Steel |
| Protection Class | IPX8 |
| Maximum Liquid Temperature | 40°C |
| Maximum Immersion Depth | Up to 5 m* |
| Installation | Fully Submersible |
*Material and configuration descriptions can vary between regional LEO listings. One Malaysian listing specifically identifies the LSWM150XA as an X/semi-open impeller model, while another describes the same model as a vortex-impeller sewage pump. The 1.1 kW, 1.5 HP, 220 V, 383 L/min, 11.5 m and 2-inch specifications are consistent across the Malaysian listings.
1.5 HP / 1.1 kW Motor
The LSWM150XA is powered by a 1.1 kW / 1.5 HP motor, giving it substantially greater pumping capacity than the smaller LSWM75XA and LSWM100XA models.
The Malaysian configuration operates at 220 V, making it suitable for installations where single-phase power is available.
The motor incorporates a built-in thermal protector, while the LEO sewage-pump range uses Class F insulation. These features help protect the motor from excessive temperature under abnormal operating conditions.
For permanent installations, appropriate circuit protection should still be provided.
383 L/min Maximum Flow
The LSWM150XA has a published maximum flow of 383 L/min, equivalent to approximately 23.0 m³/h.
This high flow capacity makes the pump suitable for rapidly removing wastewater from larger collection pits, drainage tanks and sewage systems.
Typical applications include:
- Sewage collection pits
- Wastewater tanks
- Septic tanks
- Drainage sumps
- Construction-site drainage
- Factory wastewater
- Commercial drainage
- Municipal sewage systems
- Agricultural wastewater
The 383 L/min figure is the maximum flow rating. Actual flow depends on the total system head, pipe diameter, pipe length and other hydraulic losses.
11.5-Metre Maximum Head
The LSWM150XA is specified with a maximum head of 11.5 metres.
This provides useful capacity for applications requiring moderate vertical lifting, including:
- Basement drainage
- Deep sewage pits
- Wastewater collection tanks
- Septic systems
- Commercial drainage stations
- Construction drainage
- Short-to-medium discharge pipelines
A maximum head rating does not mean the pump will deliver its maximum flow at 11.5 m. The actual duty point must be determined from the pump curve.
The hydraulic requirement should account for:
Total Dynamic Head = Static Lift + Pipe Friction Loss + Fitting Losses + Valve/Check-Valve Losses
2-Inch Discharge Outlet
The LSWM150XA uses a 2-inch discharge outlet.
The 2-inch outlet is appropriate for the pump's relatively high flow capacity and helps control friction losses in the discharge system.
For best performance, the discharge pipe should be correctly sized. Excessively small hoses or long discharge lines can significantly reduce actual flow.
Wastewater Impeller Design
The LSWM150XA is intended for wastewater and sewage containing suspended impurities.
The Malaysian Kokent listing identifies the model as LSWM150XA, with X indicating a semi-open impeller. Another Malaysian retailer describes the LSWM150XA as using a vortex impeller and lists a 30 mm solid passage.
Because these descriptions differ between regional listings, the safest catalog description is:
Wastewater/sewage impeller configuration designed for liquids containing suspended impurities.
The pump should not be treated as a grinder pump. Large cloth, ropes, plastic bags, long fibres and oversized solid objects can still cause blockage.
LEO's sewage-pump range also includes dedicated grinding models for applications requiring the breakdown of larger solids.
Automatic Float-Switch Operation
The XA version is designed for automatic operation using a float switch. The float controls the pump according to the wastewater level.
The normal sequence is:
Water level rises → Float activates → Pump starts → Water level falls → Float deactivates → Pump stops
This is particularly useful for sewage pits, drainage sumps and wastewater tanks because the pump can operate automatically without continuous manual supervision.
The float should have adequate clearance and must not become trapped against the tank wall, pipework or other equipment.
AISI 304 Stainless-Steel Components
The LSWM150XA is specified with AISI 304 fabricated shaft, handle and pump body in Malaysian product listings.
AISI 304 stainless steel provides good corrosion resistance in wet environments and is suitable for equipment operating in wastewater.
The stainless-steel shaft also provides improved durability around the rotating assembly and mechanical-seal area.
Built-In Thermal Protection
The pump features a built-in thermal protector. This helps protect the motor against excessive temperature resulting from overload or abnormal operating conditions.
Thermal protection should be considered an additional safety feature. Correct electrical protection, proper installation and correct pump selection remain necessary.
Class F Insulation
The LSWM150XA uses Class F motor insulation. Malaysian product specifications explicitly identify Class F insulation.
This provides suitable thermal resistance for the motor and supports reliable operation within the manufacturer's specified conditions.
IPX8 Submersible Protection
LEO's sewage-pump range specifies IPX8 protection, appropriate for equipment designed to operate while submerged.
The LSWM150XA should be installed according to the manufacturer's requirements, particularly regarding electrical connections, grounding, cable routing and allowable immersion depth.
Operating Conditions
LEO's LSW sewage-pump documentation specifies the following general operating conditions:
- Maximum liquid temperature: 40°C
- Liquid pH: 4–10
- Maximum liquid density: 1200 kg/m³
- Solid impurity volume ratio: Maximum 2%
- Protection class: IPX8
- Insulation class: F
- Frequency: 50 Hz
The pump should not be used for strongly corrosive liquids or strongly abrasive media without confirming material compatibility with LEO.
Suitable Applications
LEO identifies its sewage submersible pumps for wastewater drainage, sewage pumping, industrial pumping and sewage-management applications.
The LSWM150XA is suitable for:
Residential
- Septic tanks
- Sewage pits
- Residential drainage stations
- Basement wastewater
Commercial
- Commercial-building drainage
- Hotels
- Restaurants
- Schools
- Public buildings
- Wastewater collection tanks
Industrial
- Factory wastewater
- Industrial drainage pits
- Wastewater transfer
- Food-processing wastewater
- General industrial drainage
Construction
- Construction-site drainage
- Excavation drainage
- Temporary wastewater pumping
- Accumulated water removal
Municipal
- Sewage-treatment plants
- Municipal drainage stations
- Wastewater collection systems
Agricultural
- Farm wastewater
- Methane pools
- Field irrigation
- Agricultural drainage
LEO specifically identifies wastewater drainage in factories and commercial facilities, municipal sewage-treatment systems, residential drainage stations, septic tanks and agricultural applications within its sewage-pump range.
Typical Installation
A typical system can be arranged as:
Sewage / wastewater collection pit → LEO LSWM150XA → 2" discharge pipe → drainage / treatment / collection point
The pump is positioned inside the collection pit and operates while submerged.
For permanent installations, a suitable check valve may be incorporated into the discharge line to reduce reverse flow after the pump stops.
The discharge pipe should be properly supported and sized according to the required flow and total discharge distance.
Pump Performance Considerations
The 383 L/min maximum flow and 11.5 m maximum head are maximum specifications and should not be interpreted as simultaneous operating conditions.
Actual performance depends on:
- Required flow rate.
- Static vertical lift.
- Discharge-pipe diameter.
- Total pipe length.
- Number of elbows and fittings.
- Check-valve and valve losses.
- Wastewater characteristics.
- Required discharge pressure.
For example, a long discharge line with several bends can produce significant friction losses even when the static lifting height is relatively low.
The correct duty point should therefore be established from the Q-H pump curve before installation.
Main Product Advantages
- 1.5 HP / 1.1 kW motor for high-capacity wastewater drainage.
- 383 L/min maximum flow.
- Approximately 23 m³/h maximum flow capacity.
- 11.5 m maximum head.
- 2-inch discharge outlet.
- Wastewater impeller configuration suitable for suspended impurities.
- Automatic float-switch operation.
- Built-in thermal protection.
- Class F motor insulation.
- AISI 304 stainless-steel fabricated shaft.
- AISI 304 stainless-steel handle and pump body in the Malaysian specification.
- IPX8 submersible protection.
- 220 V single-phase operation.
- Suitable for residential, commercial, industrial, construction, municipal and agricultural wastewater applications.
- Suitable for sewage pits, septic tanks, wastewater tanks and drainage stations.
Product Details Summary
The LEO LSWM150XA is an automatic 1.5 HP / 1.1 kW sewage submersible pump designed for high-volume wastewater, sewage and dirty-water drainage. Operating at 220 V single phase, it delivers up to 383 L/min (approximately 23 m³/h) with a maximum head of 11.5 metres through a 2-inch discharge outlet. The pump features automatic float-switch start/stop, built-in thermal protection and Class F insulation, while its AISI 304 stainless-steel fabricated shaft, handle and pump body provide good durability in wet wastewater environments. LEO's sewage-pump range is designed for applications including sewage tanks, septic systems, factories, construction sites, commercial facilities, municipal wastewater treatment and agricultural drainage.
SEO Product Title
LEO LSWM150XA Sewage Submersible Pump 1.5HP 1.1kW – 383L/min, 11.5M Head
SEO Product Description
LEO LSWM150XA Sewage Submersible Pump is an automatic 1.5HP / 1.1kW wastewater and sewage pump designed for high-capacity drainage of dirty water, sewage and wastewater containing suspended impurities. Operating at 220V/50Hz single phase, it delivers up to 383L/min (23m³/h) with a maximum head of 11.5 metres and features a 2-inch discharge outlet. The pump incorporates automatic float-switch operation, built-in thermal protection and Class F insulation, together with AISI 304 stainless-steel fabricated shaft, handle and pump body for improved durability in demanding wet environments. With IPX8 submersible protection, the LEO LSWM150XA is suitable for septic tanks, sewage pits, residential drainage stations, construction sites, factories, commercial facilities, municipal sewage-treatment systems and agricultural wastewater applications.
Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - LSWM 150XA