The LEO QDX 6-18-0.75LA is a 1 HP / 0.75 kW single-phase submersible drainage pump designed for high-volume water transfer, irrigation, drainage, well-water pumping, construction dewatering and aquaculture applications. It operates on 220 V / 50 Hz, uses a 1½-inch (40 mm) discharge outlet, and has a published maximum flow of approximately 333 L/min (20 m³/h) with a maximum head of approximately 19.5–20 m.
Although it may be listed commercially under sewage/submersible pump categories, the QDX 6-18-0.75LA is technically a drainage pump for clean or lightly contaminated water. LEO's QDX-LA specifications indicate a maximum suspended-solids passage of approximately 0.2 mm, so it should not be treated as a heavy-duty raw-sewage or sewage-cutter pump.
Product Specifications
| Specification | Details |
|---|---|
| Brand | LEO |
| Model | QDX 6-18-0.75LA |
| Pump Series | QDX-LA |
| Pump Type | Submersible Drainage Pump |
| Motor Power | 0.75 kW |
| Motor Rating | 1 HP |
| Voltage | 220 V |
| Frequency | 50 Hz |
| Phase | Single Phase |
| Maximum Flow | Approx. 333 L/min |
| Maximum Flow | Approx. 20 m³/h |
| Rated Flow | Approx. 100 L/min / 6 m³/h |
| Maximum Head | Approx. 19.5–20 m |
| Rated Head | 18 m |
| Minimum Published Head | Approx. 2–4.2 m depending on reference/performance specification |
| Discharge Outlet | 1½" / 40 mm |
| Maximum Immersion Depth | 5 m |
| Maximum Liquid Temperature | 40°C |
| Liquid pH Range | 6.5–8 |
| Maximum Sand Content | 0.1% |
| Suspended Solids | Up to approx. 0.2 mm |
| Pump Body | Cast Iron / HT200 |
| Motor Casing | Aluminium |
| Impeller | Engineering Plastic / PPO or model-specific alloy specification |
| Shaft | Stainless Steel |
| Mechanical Seal | Double-End Mechanical Seal |
| Motor Winding | Copper |
| Insulation Class | F |
| Protection Class | IP68 |
| Thermal Protection | Built-In |
| Installation | Vertical, Submersible |
| Typical Applications | Drainage, irrigation, wells, construction, aquaculture |
Published sources agree on the 0.75 kW motor, 220 V single-phase supply, 40 mm discharge, 18 m rated head, approximately 20 m maximum head and approximately 333 L/min maximum flow.
1 HP / 0.75 kW Motor
The QDX 6-18-0.75LA is fitted with a 0.75 kW / 1 HP single-phase motor operating at 220 V / 50 Hz.
This motor rating gives the pump substantially greater water-handling capability than smaller QDX models such as the QDX 3-18-0.55LA.
The motor is suitable for applications requiring relatively high flow while maintaining useful lifting capability. The design incorporates copper motor winding and built-in thermal protection for normal operating conditions.
High-Volume 333 L/min Flow
One of the major characteristics of the QDX 6-18-0.75LA is its high flow capacity.
The published maximum flow is approximately:
333 L/min = 20 m³/h
The rated flow is approximately:
100 L/min = 6 m³/h
at the rated operating head of approximately 18 m.
This makes the model suitable for applications where a relatively large volume of water needs to be transferred or removed quickly.
Typical applications include:
- Large drainage pits
- Construction-site dewatering
- Agricultural irrigation
- Pond drainage
- Tank emptying
- Well-water transfer
- Industrial accumulated-water drainage
- Aquaculture
- Floodwater removal
19.5–20 Metre Maximum Head
The QDX 6-18-0.75LA provides approximately 19.5–20 m maximum head, while the nominal/rated head is approximately 18 m.
This makes it suitable for both moderate-flow/high-head and high-flow/lower-head applications.
As with all centrifugal pumps, the maximum head and maximum flow do not occur simultaneously. As the discharge head increases, available flow decreases.
Approximate Hydraulic Performance
LEO's published performance curve gives the following approximate relationship for the QDX 6-18-0.75LA:
| Flow | Approx. Head |
|---|---|
| 0 L/min | 19.5 m |
| 33 L/min | 19.4 m |
| 67 L/min | 18.8 m |
| 100 L/min | 18.0 m |
| 133 L/min | 17.7 m |
| 167 L/min | 16.0 m |
| 200 L/min | 14.2 m |
| 233 L/min | Approx. 12 m |
| 267 L/min | Approx. 10 m |
| 300 L/min | Approx. 6 m |
| 333 L/min | Approx. 2 m |
The published LEO performance documentation shows the characteristic curve extending from approximately 19.5 m head at zero flow to approximately 2 m at 333 L/min.
For actual installation, the operating point will depend on total dynamic head, pipe diameter, pipe length, fittings, valves and other system losses.
1½-Inch / 40 mm Discharge
The QDX 6-18-0.75LA uses a relatively large 1½-inch / 40 mm discharge outlet, allowing it to handle considerably greater flow than the 1-inch QDX models.
The larger outlet is particularly useful for:
- Rapid drainage
- Large water tanks
- Construction dewatering
- Pond drainage
- Irrigation
- Long discharge lines
Using an undersized discharge hose can introduce significant friction losses and reduce the pump's actual flow.
For high-flow applications, the discharge pipe or hose should therefore be appropriately sized.
Cast-Iron Pump Body
The pump uses a cast-iron pump body, with technical documentation identifying the main pump housing material as HT200 cast iron.
Cast iron provides:
- High mechanical strength
- Good durability
- Resistance to mechanical impact
- Stable support for hydraulic components
- Suitable service life for drainage applications
The QDX-LA series also incorporates anti-rust treatment on the pump body.
Aluminium Motor Casing
The motor casing is constructed from aluminium.
The aluminium housing helps keep the pump relatively compact while providing effective heat transfer from the motor.
This is useful for a portable drainage pump that may be installed and removed frequently.
Stainless-Steel Shaft
The pump incorporates a stainless-steel shaft.
Because the shaft operates inside a submerged pump, corrosion resistance is important.
The stainless-steel shaft provides:
- Corrosion resistance
- Mechanical strength
- Reliable rotating operation
- Improved durability in wet environments
Double-End Mechanical Seal
The QDX-LA series uses a double-end mechanical seal.
The mechanical seal creates a barrier between the hydraulic section and motor chamber, helping prevent pumped liquid from entering the motor through the rotating shaft.
This is particularly important for submersible equipment because the entire pump operates within the pumped liquid.
Impeller
Published specifications identify an engineering-plastic impeller, with PPO/PA6-type engineering plastic cited for QDX variants, while some technical listings identify specific component materials according to the local configuration.
The impeller is designed to provide the hydraulic performance required by the QDX 6-18-0.75LA while maintaining a relatively lightweight rotating assembly.
Copper Motor Winding
The motor uses copper winding, providing good electrical conductivity and appropriate thermal characteristics.
Copper winding is well suited to the motor's 0.75 kW power rating and supports reliable operation when the pump is operated within its specified electrical and hydraulic limits.
Built-In Thermal Protector
The pump incorporates a built-in thermal protector.
This protects the motor against excessive temperature under abnormal operating conditions such as overload.
The thermal protector does not replace external electrical protection. The installation should still include appropriate circuit protection, grounding and correctly sized electrical cable.
Class F Insulation
The motor is specified with Class F insulation.
Class F insulation provides suitable thermal resistance for the motor winding system and is appropriate for the pump's intended operating conditions.
IP68 Protection
The QDX 6-18-0.75LA is specified with IP68 protection for submerged operation.
This makes it suitable for:
- Drainage pits
- Wells
- Water tanks
- Construction excavations
- Flooded areas
- Ponds
- Agricultural drainage
The specified maximum immersion depth is 5 metres.
Maximum Immersion Depth – 5 m
The maximum installation/immersion depth is approximately 5 m.
The pump should be installed securely and should not be suspended by its electrical cable.
For dirty-water applications, it is preferable to position the pump away from heavy sediment whenever possible. Excessive abrasive material can accelerate wear of the mechanical seal and hydraulic components.
Maximum Liquid Temperature – 40°C
The maximum liquid temperature is 40°C.
Suitable applications therefore include normal-temperature:
- Fresh water
- Rainwater
- Irrigation water
- Well water
- Drainage water
- Lightly contaminated water
The pump should not be used for high-temperature industrial liquids unless specifically approved by the manufacturer.
Liquid pH and Sand Content
The QDX-LA series is specified for liquid with a pH of approximately 6.5–8 and maximum sand content of approximately 0.1%.
These restrictions help protect the mechanical seal and hydraulic components from excessive chemical or abrasive exposure.
Suspended Solids
The LEO QDX-LA specification indicates a suspended-solids passage of approximately 0.2 mm.
This is an important distinction for product classification.
The QDX 6-18-0.75LA is appropriate for clean or lightly contaminated drainage water, but it should not be selected for heavy raw sewage containing large solids, rags or fibrous waste.
Some third-party listings provide different particle-size figures for specific configurations or regional documentation, so the manufacturer's nameplate/manual should be used for final solids-handling confirmation.
Sewage Application Limitation
For website classification, it is reasonable to place this model under a broad "Sewage / Submersible Pumps" category if that matches your existing catalogue structure. Technically, however, the more precise description is:
Submersible Drainage Pump
It is intended for water and lightly contaminated liquids rather than heavy raw sewage.
It should not be used for pumping:
- Rags
- Rope
- Plastic waste
- Large fibrous materials
- Stones
- Construction debris
- Thick sludge
- Large organic solids
For these conditions, a dedicated sewage pump with a larger solids passage or cutter mechanism is more appropriate.
Suitable Applications
LEO's QDX-LA series is intended for small irrigation and drainage systems, rural well-water pumping, farming irrigation and drainage, industrial/construction accumulated-water drainage and aquaculture.
Agricultural applications
- Farm irrigation
- Agricultural drainage
- Rural well-water pumping
- Garden irrigation
- Livestock water systems
Construction applications
- Excavation dewatering
- Foundation drainage
- Construction-site water removal
- Temporary dewatering
- Accumulated-water drainage
Residential applications
- Pond drainage
- Water tank emptying
- Basement drainage
- Garden irrigation
- General water transfer
Industrial applications
- Industrial accumulated-water drainage
- Equipment-area drainage
- Utility water transfer
- Process-area water removal
Aquaculture
- Pond drainage
- Tank drainage
- Water transfer
- Aquaculture water management
Typical Installation
A typical system can be arranged as:
Drainage pit / well / pond → QDX 6-18-0.75LA → 1½" discharge hose or pipe → drainage point / tank / irrigation system
The pump is placed directly into the water and the discharge line is connected to the 1½-inch outlet.
For permanent installations, the discharge pipe should be properly supported so its weight does not place excessive stress on the pump outlet.
For portable applications, the pump can be moved between drainage locations as required.
Pump Positioning
For reliable operation:
- Keep the pump adequately submerged.
- Do not exceed the 5 m maximum immersion depth.
- Place the pump on a stable surface.
- Keep the inlet area free from excessive debris.
- Avoid heavy sediment deposits.
- Do not lift the pump by its electrical cable.
- Protect the cable from abrasion and mechanical damage.
- Ensure the discharge line is securely connected.
- Avoid unnecessary restrictions in the discharge pipe.
Why Choose the QDX 6-18-0.75LA?
The QDX 6-18-0.75LA is particularly useful when the application requires a combination of high flow and moderate lifting height.
Compared with smaller QDX models, its 1½-inch outlet and 333 L/min maximum flow provide substantially greater water-transfer capacity. At the same time, the pump can produce approximately 18 m rated head, making it suitable for applications where a simple low-head drainage pump would not be sufficient.
Main Product Advantages
- 1 HP / 0.75 kW motor.
- 220 V / 50 Hz single-phase operation.
- Up to approximately 333 L/min flow.
- Approximately 20 m³/h maximum flow.
- Approximately 19.5–20 m maximum head.
- 18 m rated head.
- Large 1½-inch / 40 mm discharge outlet.
- Cast-iron pump body.
- Aluminium motor casing.
- Stainless-steel shaft.
- Double-end mechanical seal.
- Copper motor winding.
- Built-in thermal protection.
- Class F insulation.
- IP68 protection.
- Maximum immersion depth of 5 m.
- Maximum liquid temperature of 40°C.
- Suitable for irrigation, drainage, wells, construction and aquaculture.
- High-flow design for rapid water removal.
- Suitable for portable and fixed drainage installations.
Product Details Summary
The LEO QDX 6-18-0.75LA is a 1 HP / 0.75 kW single-phase high-flow submersible drainage pump designed for agricultural irrigation, drainage, rural well-water pumping, construction dewatering, pond drainage, aquaculture and general water transfer. Operating at 220 V / 50 Hz, it features a 1½-inch / 40 mm discharge outlet, approximately 333 L/min (20 m³/h) maximum flow, approximately 19.5–20 m maximum head and an 18 m rated head. Its construction includes a cast-iron pump body, aluminium motor casing, stainless-steel shaft, double-end mechanical seal and copper motor winding, together with built-in thermal protection, Class F insulation and IP68 protection. The pump is suitable for immersion up to 5 metres and liquids up to 40°C, with a recommended pH range of 6.5–8. It is best suited to clean or lightly contaminated water and drainage applications rather than heavy raw sewage containing large solids or fibrous waste.
SEO Product Title
LEO QDX 6-18-0.75LA Submersible Drainage Pump 1HP 0.75kW – 20M Head
SEO Product Description
LEO QDX 6-18-0.75LA Submersible Drainage Pump is a high-flow 1HP / 0.75kW, 220V single-phase submersible pump designed for agricultural irrigation, drainage, well-water pumping, construction dewatering, pond drainage, aquaculture and general water-transfer applications. With a 1½-inch / 40mm discharge outlet, the pump delivers up to approximately 333L/min (20m³/h) and provides approximately 19.5–20 metres maximum head with 18 metres rated head. It features a durable cast-iron pump body, aluminium motor casing, stainless-steel shaft and double-end mechanical seal, together with copper motor winding, built-in thermal protection, Class F insulation and IP68 protection. With a maximum immersion depth of 5 metres and maximum liquid temperature of 40°C, the LEO QDX 6-18-0.75LA provides a practical high-volume solution for drainage, irrigation, construction sites, wells, ponds and aquaculture applications.
Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - QDX 6-18-0.75LA