B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO SEWAGE SUBMERSIBLE PUMPS - QDX 15-10-0.75LA



The LEO QDX 15-10-0.75LA is a high-volume 0.75 kW / 1 HP single-phase submersible drainage pump designed for moving large quantities of clean or lightly contaminated water. It is suitable for agricultural irrigation, drainage, rural well-water pumping, garden watering, construction-site dewatering, fish ponds, aquaculture and general water transfer. LEO's QDX-LA catalogue specifies 220 V, 25–475 L/min flow, 10.9–2.7 m head, 5 m maximum immersion depth, 0.75 kW / 1 HP motor and a 65 mm outlet.

For technical classification, this model is more accurately described as a submersible drainage pump rather than a heavy-duty raw-sewage pump. The QDX-LA specification allows suspended solids up to approximately 0.2 mm and sand content up to 0.1%, so it should not be used for wastewater containing large solids, rags, ropes or fibrous materials.

Product Specifications

Specification Details
Brand LEO
Model QDX 15-10-0.75LA
Series QDX-LA
Pump Type Submersible Drainage Pump
Motor Power 0.75 kW
Motor Rating 1 HP
Voltage 220 V
Frequency 50 Hz
Phase Single Phase
Maximum Flow Approx. 475 L/min*
Maximum Flow Approx. 28.5 m³/h*
Rated Flow Approx. 249 L/min / 14.9 m³/h**
Maximum Head Approx. 10.9–12 m*
Rated Head Approx. 10 m
Minimum Published Head Approx. 2.7 m*
Outlet 65 mm / 2½"
Maximum Immersion Depth 5 m
Maximum Liquid Temperature 40°C
Liquid pH Range 6.5–8
Maximum Sand Content 0.1%
Suspended-Solid Passage Up to approx. 0.2 mm
Pump Body Cast Iron
Motor Casing Aluminium
Impeller Engineering Polymer
Shaft Stainless Steel
Motor Winding Copper
Mechanical Seal Double-End Mechanical Seal
Insulation Class F
Protection Class IP68
Thermal Protection Built-In
Installation Vertical / Submersible

* LEO's QDX-LA catalogue lists 25–475 L/min and 10.9–2.7 m head. Some distributor specifications report a slightly different maximum flow/head depending on the test curve or regional documentation.

** A separate technical listing reports approximately 249 L/min / 14.95 m³/h at 10 m rated head, with approximately 415 L/min / 24.9 m³/h maximum flow and 12 m maximum head.

0.75 kW / 1 HP Motor

The QDX 15-10-0.75LA is equipped with a 0.75 kW / 1 HP single-phase motor designed for 220 V, 50 Hz operation. LEO's catalogue identifies this exact power and electrical configuration.

The 1 HP motor is designed primarily for high-volume water movement at relatively low-to-moderate head, rather than high-pressure pumping.

This makes it particularly suitable for:

  • Large-area drainage
  • Agricultural irrigation
  • Pond emptying
  • Construction dewatering
  • Water transfer
  • Rural wells
  • Aquaculture

The motor incorporates copper winding and built-in thermal protection, helping protect the motor under normal operating conditions.

High-Volume Water Flow

The QDX 15-10-0.75LA is designed around a relatively high-flow hydraulic profile.

LEO's QDX-LA catalogue gives a flow range of approximately:

25–475 L/min

This corresponds to approximately:

1.5–28.5 m³/h

at the extremes of the published performance range.

Another technical source gives approximately 415 L/min / 24.9 m³/h maximum flow and approximately 249 L/min / 14.95 m³/h nominal flow.

For website listings, it is therefore advisable to present up to approximately 475 L/min when following the LEO QDX-LA catalogue, while noting that actual operating flow depends on the system head.

Approximately 11–12 Metre Maximum Head

The QDX 15-10-0.75LA is a high-flow, low-head drainage pump.

LEO's QDX-LA catalogue specifies a maximum head of approximately 10.9 m, falling to approximately 2.7 m across the published flow range.

Other technical listings identify approximately 12 m maximum head and 10 m nominal/rated head.

This makes the model appropriate where large quantities of water need to be moved through relatively short or moderate-height discharge systems.

It is not intended to replace a high-head multistage pump where substantial vertical lifting pressure is required.

Hydraulic Performance

The basic designation 15-10 indicates the pump's approximate nominal hydraulic class: approximately 15 m³/h flow at 10 m head.

A technical listing gives:

  • Nominal flow: approximately 249 L/min / 14.95 m³/h
  • Nominal head: 10 m
  • Maximum flow: approximately 415 L/min / 24.9 m³/h
  • Maximum head: approximately 12 m

The LEO catalogue gives the broader performance envelope of approximately 25–475 L/min and 10.9–2.7 m head.

Actual performance depends on the total dynamic head of the installation.

Factors affecting the operating point include:

  • Vertical lifting height
  • Discharge pipe length
  • Pipe diameter
  • Hose diameter
  • Elbows
  • Valves
  • Check valves
  • Pipe friction
  • Water characteristics

65 mm / 2½-Inch Discharge

One of the most important characteristics of this model is its 65 mm / 2½-inch discharge outlet. LEO's QDX-LA catalogue specifies 65 mm for the QDX 15-10-0.75LA.

The large outlet is designed to support the pump's high-volume water-transfer capability.

A larger discharge line can help reduce friction losses, particularly when the pump is being used for:

  • Large drainage pits
  • Construction dewatering
  • Agricultural irrigation
  • Pond drainage
  • Floodwater removal
  • Large water tanks
  • Aquaculture

Using a significantly smaller hose can restrict the pump and reduce actual flow.

Cast-Iron Pump Body

The pump uses a cast-iron pump body. LEO's QDX-LA construction specifies a cast-iron body, while technical listings identify cast iron for the main pump housing.

Cast iron provides:

  • Good mechanical strength
  • Durable hydraulic housing
  • Resistance to physical impact
  • Stable support for internal components
  • Good suitability for drainage applications

The LEO QDX-LA design combines the cast-iron pump body with an aluminium motor casing.

Aluminium Motor Casing

The motor casing is made from aluminium.

Aluminium provides useful heat dissipation while keeping the overall pump construction relatively manageable for portable drainage applications.

This construction is particularly practical when the pump needs to be moved between:

  • Construction sites
  • Agricultural areas
  • Ponds
  • Drainage pits
  • Water tanks

Stainless-Steel Shaft

The QDX 15-10-0.75LA incorporates a stainless-steel shaft. LEO specifies a stainless-steel shaft for the QDX-LA series.

The shaft is exposed to the wet internal pump environment, so corrosion resistance is important.

Benefits include:

  • Corrosion resistance
  • Good mechanical strength
  • Reliable shaft rotation
  • Improved durability
  • Suitability for submerged operation

Engineering-Polymer Impeller

The QDX-LA series uses an engineering-polymer impeller, with technical listings identifying high-strength engineering polymer for this model.

The impeller is designed to provide the hydraulic performance required for high-volume drainage while maintaining a relatively lightweight rotating assembly.

The pump should not be exposed to large stones, metal objects, ropes, rags or other oversized debris.

Double-End Mechanical Seal

The QDX-LA series incorporates a double-end mechanical seal.

The mechanical seal provides a barrier around the rotating shaft between the pump's hydraulic chamber and motor section.

This is particularly important for a submersible pump because the pump operates directly inside the liquid.

A properly functioning mechanical seal helps prevent water ingress into the motor compartment.

Copper Motor Winding

The motor incorporates copper winding.

Copper provides high electrical conductivity and suitable thermal characteristics for the 0.75 kW motor.

This contributes to reliable motor operation when the pump is operated within the manufacturer's specified voltage, temperature and hydraulic conditions.

Built-In Thermal Protection

The QDX-LA series includes a built-in thermal protector.

The thermal protection helps protect the motor from excessive temperature during abnormal conditions such as overload.

External electrical protection remains necessary. The installation should include suitable:

  • Circuit protection
  • Grounding
  • Cable sizing
  • Electrical isolation

Class F Insulation

The motor uses Class F insulation according to the QDX-LA specifications.

Class F insulation provides appropriate thermal resistance for the motor winding system and supports reliable operation within the manufacturer's specified operating conditions.

IP68 Protection

The QDX 15-10-0.75LA is specified with IP68 protection, making it suitable for submerged operation.

This is appropriate for applications including:

  • Wells
  • Drainage pits
  • Ponds
  • Water tanks
  • Construction excavations
  • Flooded areas
  • Agricultural drainage

The IP68 rating should be considered together with the manufacturer's 5 m maximum immersion depth.

Maximum Immersion Depth – 5 m

The maximum specified immersion depth is 5 metres.

For safe installation:

  • Do not exceed 5 m immersion depth.
  • Do not lift the pump using the electrical cable.
  • Use a suitable rope, chain or lifting arrangement.
  • Position the pump securely.
  • Keep the suction/inlet area clear.
  • Avoid placing the pump directly into heavy sediment.

A manufacturer's installation manual for the QDX series specifically instructs users to use a rope, cable or chain for lowering and lifting rather than the electrical cable.

Maximum Liquid Temperature – 40°C

The maximum specified liquid temperature for the QDX-LA series is 40°C.

The pump is therefore intended for normal-temperature water and lightly contaminated drainage liquids.

Suitable liquids include:

  • Fresh water
  • Rainwater
  • Well water
  • Irrigation water
  • Pond water
  • Drainage water

It should not be used for hot industrial liquids without specific manufacturer approval.

Liquid pH Range

The QDX-LA series is specified for liquids with a pH range of 6.5–8.

This makes the pump primarily suitable for normal water and relatively neutral drainage liquids.

Strongly acidic or alkaline liquids may damage the pump's mechanical seal, metal components or other wetted parts.

Sand and Suspended Solids

LEO specifies a maximum sand content of 0.1% and suspended-solid passage of approximately 0.2 mm for the QDX-LA series.

This means the pump can handle lightly contaminated drainage water, but it is not designed for large solid waste.

Avoid pumping:

  • Large stones
  • Gravel
  • Rags
  • Rope
  • Plastic waste
  • Fibrous material
  • Thick sludge
  • Large organic solids
  • Construction debris

Sewage Application Limitation

Although the model may be marketed under a LEO Sewage Submersible Pumps category, its technical design is that of a submersible drainage pump.

This distinction is important for product selection.

The QDX 15-10-0.75LA is appropriate for clean and lightly contaminated water, including drainage and wastewater without large solids.

It does not have the large solids-handling capability of a dedicated municipal sewage pump or grinder/cutter pump.

For heavy sewage applications containing rags, fibrous material or large solids, a purpose-designed sewage pump should be selected instead.

Suitable Applications

LEO identifies the QDX-LA range for irrigation and drainage equipment, rural well-water pumping, farming irrigation and drainage, industrial/construction accumulated-water drainage and aquaculture.

Agricultural

  • Farm irrigation
  • Agricultural drainage
  • Rural well-water pumping
  • Garden irrigation
  • Water transfer for farming

Construction

  • Excavation dewatering
  • Foundation drainage
  • Construction-site water removal
  • Temporary dewatering
  • Accumulated-water removal

Residential

  • Pond drainage
  • Water tank emptying
  • Garden watering
  • Basement drainage
  • General water transfer

Aquaculture

  • Fish pond drainage
  • Tank water transfer
  • Pond emptying
  • Aquaculture water management

Industrial

  • Industrial accumulated-water drainage
  • Equipment-area drainage
  • General water transfer
  • Non-aggressive liquid drainage

High-Flow Drainage Applications

The QDX 15-10-0.75LA is particularly useful where volume is more important than high pressure.

For example, it can be used to rapidly remove accumulated water from a large construction excavation, transfer pond water or move irrigation water through a relatively short discharge system.

Its 65 mm discharge outlet and high-flow performance make it more suitable for large-volume drainage than smaller QDX models with 25 mm or 40 mm outlets.

Typical Installation

A typical installation can be arranged as:

Well / pond / drainage pit → LEO QDX 15-10-0.75LA → 2½" discharge hose/pipe → drainage area / tank / irrigation system

The pump is submerged directly in the water source.

For permanent installations, the discharge pipe should be adequately supported. The weight of a long pipe or hose should not be transferred directly to the pump outlet.

For temporary applications, the pump can be installed and removed as required.

Installation Recommendations

For reliable operation:

  • Keep the pump sufficiently submerged.
  • Do not exceed the 5 m maximum immersion depth.
  • Place the pump on a stable base where possible.
  • Keep the inlet/filter area free from excessive debris.
  • Avoid heavy sediment accumulation.
  • Use an appropriate 65 mm / 2½" discharge line.
  • Minimise unnecessary bends and restrictions.
  • Do not lift the pump using the electrical cable.
  • Use a rope, chain or suitable lifting arrangement.
  • Ensure proper electrical grounding.
  • Use appropriate circuit protection.

Key Product Advantages

  1. 1 HP / 0.75 kW motor.
  2. 220 V / 50 Hz single-phase operation.
  3. High-volume drainage performance.
  4. Up to approximately 475 L/min according to the LEO QDX-LA catalogue.
  5. Up to approximately 28.5 m³/h according to the catalogue flow range.
  6. Approximately 10.9 m maximum head according to the LEO catalogue.
  7. Approximately 10 m rated head.
  8. Large 65 mm / 2½" discharge outlet.
  9. Cast-iron pump body.
  10. Aluminium motor casing.
  11. Stainless-steel shaft.
  12. Engineering-polymer impeller.
  13. Double-end mechanical seal.
  14. Copper motor winding.
  15. Built-in thermal protection.
  16. Class F insulation.
  17. IP68 protection.
  18. Maximum immersion depth of 5 m.
  19. Maximum liquid temperature of 40°C.
  20. Suitable for irrigation, drainage, wells, construction and aquaculture.

Product Details Summary

The LEO QDX 15-10-0.75LA is a 1 HP / 0.75 kW, 220 V single-phase high-volume submersible drainage pump designed for agricultural irrigation, rural well-water pumping, construction dewatering, pond drainage, aquaculture and general water transfer. LEO's QDX-LA catalogue specifies a 25–475 L/min flow range, 10.9–2.7 m head range, 65 mm outlet and 5 m maximum immersion depth.

The pump features a cast-iron pump body, aluminium motor casing, engineering-polymer impeller, stainless-steel shaft and double-end mechanical seal, together with copper winding, built-in thermal protection, Class F insulation and IP68 protection. It is designed for liquids up to 40°C, with a pH range of 6.5–8, maximum sand content of 0.1% and suspended solids up to approximately 0.2 mm.

The model is particularly suitable for high-volume, relatively low-head applications where rapid water removal or transfer is required. Distributor specifications commonly identify approximately 10–12 m maximum head and approximately 415–475 L/min maximum flow, depending on the particular performance reference used.

SEO Product Title

LEO QDX 15-10-0.75LA Submersible Drainage Pump 1HP 0.75kW – 11M Head, 2½" Outlet

SEO Product Description

LEO QDX 15-10-0.75LA Submersible Drainage Pump is a high-volume 1HP / 0.75kW, 220V single-phase pump designed for agricultural irrigation, drainage, rural well-water pumping, construction dewatering, pond drainage, aquaculture and general water transfer. Featuring a large 65mm / 2½-inch discharge outlet, the QDX 15-10-0.75LA provides a published flow range of approximately 25–475L/min, with approximately 10.9m maximum head according to LEO's QDX-LA catalogue. The pump is constructed with a cast-iron pump body, aluminium motor casing, engineering-polymer impeller, stainless-steel shaft and double-end mechanical seal, supported by copper motor winding, built-in thermal protection, Class F insulation and IP68 protection. With a maximum immersion depth of 5 metres and maximum liquid temperature of 40°C, it provides a practical high-capacity solution for drainage, irrigation, construction sites, wells, ponds and aquaculture.



 Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - QDX 15-10-0.75LA