The LEO QDX 10-18-1.1A is a 1.1 kW / 1.5 HP single-phase automatic submersible pump designed for water drainage, irrigation, well-water transfer, construction dewatering, livestock applications and general water transfer. It operates on 220 V and features a 2-inch / 50 mm discharge outlet, with a published hydraulic range of approximately 25–275 L/min and 25.5–4 m head. The model includes a float switch for automatic operation and is rated IP68 for submerged operation.
Although it is often listed commercially under sewage submersible pumps, the QDX 10-18-1.1A is technically a QDX submersible drainage pump rather than a heavy-duty raw-sewage or grinder pump. LEO specifies the QDX series for clean or lightly contaminated water and gives the QDX-LA family a suspended-solids passage of approximately 0.2 mm. Therefore, it is not intended for wastewater containing large rags, ropes, fibrous waste, stones or heavy solids.
Product Specifications
| Specification | Details |
|---|---|
| Brand | LEO |
| Model | QDX 10-18-1.1A |
| Pump Series | QDX-A / QDX Submersible Pump |
| Pump Type | Automatic Submersible Drainage Pump |
| Motor Power | 1.1 kW |
| Motor Rating | 1.5 HP |
| Voltage | 220 V |
| Phase | Single Phase |
| Frequency | 50 Hz |
| Maximum Flow | Approx. 275 L/min |
| Maximum Flow | Approx. 16.5 m³/h |
| Head Range | Approx. 25.5–4 m |
| Maximum Head | Approx. 25.5–25.8 m |
| Rated / Working Head | Approx. 18 m class |
| Discharge Outlet | 50 mm / 2" |
| Maximum Immersion Depth | 5 m |
| Maximum Liquid Temperature | 40°C |
| Liquid pH Range | 6.5–8 |
| Pump Body | Cast Iron HT200 |
| Impeller | PPO / ZL102 |
| Shaft | Stainless Steel |
| Mechanical Seal | Carbon / Ceramic |
| O-Rings | NBR |
| Motor Winding | Copper |
| Insulation Class | B |
| Protection Class | IP68 |
| Thermal Protection | Built-In |
| Automatic Control | Float Switch |
| Pump Dimensions | Approx. 270 × 190 mm body dimensions |
| Packed Weight | Approx. 22 kg |
| Typical Applications | Drainage, irrigation, wells, construction, livestock, aquaculture |
LEO's QDX documentation specifies 220 V, 25–275 L/min, 25.5–4 m head, 5 m immersion depth, 1.1 kW / 1.5 HP and 50 mm outlet for the QDX 10-18-1.1A. LEO's product information also specifies the QDX-A series with a cast-iron pump body, stainless-steel shaft, built-in thermal protector, Class B insulation and IP68 protection.
1.1 kW / 1.5 HP Motor
The QDX 10-18-1.1A uses a 1.1 kW / 1.5 HP single-phase motor designed for 220 V operation. This gives the pump considerably more power than the 0.55 kW and 0.75 kW QDX models and allows it to achieve a substantially higher maximum head of approximately 25.5–25.8 m.
The motor is suitable for applications where water needs to be lifted through a relatively high vertical distance while maintaining useful flow. Typical applications include transferring water from wells, drainage pits, ponds and tanks, as well as construction-site dewatering and agricultural irrigation.
High-Pressure QDX Configuration
The QDX 10-18-1.1A is one of the higher-head models in the QDX range. LEO's performance table gives approximately 25.8 m head at shut-off, falling progressively as flow increases. The published performance points include approximately 25.5 m at 25 L/min, 25 m at 50 L/min, 24.6 m at 75 L/min, 24 m at 100 L/min, 22.8 m at 120 L/min, 21.2 m at 150 L/min, 18.5 m at 175 L/min, 16 m at 200 L/min, 13.2 m at 225 L/min, 9 m at 250 L/min and 4 m at 275 L/min.
This demonstrates an important characteristic of the model: maximum flow and maximum head do not occur at the same operating point.
For example:
- At approximately 175 L/min, the available head is about 18.5 m.
- At approximately 200 L/min, the available head is about 16 m.
- At approximately 225 L/min, the available head is about 13.2 m.
- At approximately 250 L/min, the available head is about 9 m.
- At approximately 275 L/min, the available head falls to about 4 m.
This makes the QDX 10-18-1.1A suitable for installations requiring a balance between moderate-to-high lifting height and water-transfer capacity.
Approx. 25.5–25.8 m Maximum Head
The QDX 10-18-1.1A has a maximum head of approximately 25.5–25.8 metres, depending on the published source and performance reference. LEO's own performance table gives 25.8 m at zero flow and approximately 25.5 m at 25 L/min.
The model designation “18” should not be interpreted as the absolute maximum head. The actual performance curve reaches approximately 25.8 m at very low/no flow, while the pump operates across a range of flow and head combinations.
Actual head at the installation will depend on:
- Vertical lifting height
- Pipe length
- Discharge pipe diameter
- Elbows and bends
- Valves
- Check valves
- Hose restrictions
- Friction losses
- Required flow rate
Maximum Flow – Approx. 275 L/min
The published maximum flow is approximately 275 L/min, equivalent to approximately:
275 × 60 ÷ 1,000 = 16.5 m³/h
LEO's performance table shows the pump reaching approximately 275 L/min at around 4 m head. At higher discharge heads, the available flow decreases.
This makes the pump useful for applications where a substantial volume of water must be transferred through a relatively high lifting system.
2-Inch / 50 mm Discharge Outlet
The pump is equipped with a 50 mm / 2-inch discharge outlet. LEO's QDX product data specifies a 50 mm outlet for the QDX 10-18-1.1A.
The 2-inch discharge is appropriate for applications such as:
- Construction dewatering
- Well-water transfer
- Agricultural irrigation
- Pond drainage
- Tank filling
- General drainage
- Livestock water management
Using an appropriately sized discharge hose helps reduce friction losses and allows the pump to operate closer to its intended performance curve.
Cast-Iron Pump Body
The QDX 10-18-1.1A uses a cast-iron HT200 pump body. LEO's material table identifies the pump body and several upper components as HT200.
Cast iron provides good mechanical strength and durability for submersible drainage applications.
The pump body is designed to withstand the mechanical loads generated by the rotating hydraulic assembly while operating in a submerged environment.
Stainless-Steel Shaft
The pump incorporates a stainless-steel shaft. This is an important component because the shaft operates inside the wet pump assembly and is exposed to the pumped liquid.
The stainless-steel construction provides:
- Corrosion resistance
- Good mechanical strength
- Reliable rotating performance
- Improved durability in wet environments
- Resistance to normal water-related corrosion
PPO / ZL102 Impeller
LEO's QDX product material table identifies the impeller as PPO/ZL102.
The impeller is responsible for converting the motor's rotational energy into hydraulic energy, generating the pressure and flow required for water transfer.
The pump should not be used to handle large debris, stones, rags or fibrous materials that could block or damage the impeller.
Carbon / Ceramic Mechanical Seal
The QDX 10-18-1.1A uses a carbon/ceramic mechanical seal. LEO's QDX material table identifies the mechanical seal materials as carbon/ceramic.
The mechanical seal provides the critical barrier between the rotating shaft and the motor chamber.
This is particularly important for a submersible pump because the motor and hydraulic assembly operate within or directly adjacent to the pumped liquid.
Copper Motor Winding
The QDX motor uses copper winding. This provides good electrical conductivity and is intended to support efficient operation of the 1.1 kW motor.
Copper winding is commonly used in submersible pump motors because of its electrical and thermal characteristics.
Built-In Thermal Protection
The QDX series incorporates a built-in thermal protector to help protect the motor against excessive temperature.
Thermal protection is useful in abnormal operating situations such as:
- Motor overload
- Excessive operating temperature
- Restricted hydraulic operation
- Electrical abnormalities
External electrical protection should still be provided during installation.
Class B Motor Insulation
The QDX-A series is specified with Class B motor insulation.
The insulation system protects the motor winding against electrical breakdown under its specified operating temperature conditions.
IP68 Protection
The pump has an IP68 protection rating, making it suitable for submerged operation.
This makes the QDX 10-18-1.1A suitable for:
- Wells
- Drainage pits
- Water tanks
- Ponds
- Construction excavations
- Agricultural water sources
- Flooded areas
The IP68 rating should be used together with the manufacturer's specified 5 m maximum immersion depth.
Automatic Float-Switch Operation
The “A” suffix on the QDX 10-18-1.1A identifies the automatic version. Commercial specifications describe the model as being equipped with a float switch, allowing the pump to start and stop automatically according to the surrounding water level.
This is useful for drainage applications because the pump does not necessarily need to be manually switched on and off.
Typical applications include:
- Sump drainage
- Water collection pits
- Drainage tanks
- Floodwater removal
- Automatic water-level control
The float switch requires sufficient free movement around the pump. It should not be trapped against the wall of a pit or obstructed by pipes, cables or debris.
Maximum Immersion Depth – 5 m
The QDX 10-18-1.1A has a specified maximum immersion depth of 5 metres.
The pump should be securely lowered into the water using an appropriate lifting rope or chain. The electrical cable should not be used as the lifting line.
For reliable operation, the pump should also be positioned so that the intake is not buried in mud or heavy sediment.
Maximum Liquid Temperature – 40°C
The maximum liquid temperature is 40°C.
The pump is intended primarily for normal-temperature water and compatible drainage liquids.
Suitable applications include:
- Fresh water
- Rainwater
- Well water
- Irrigation water
- Pond water
- Lightly contaminated drainage water
Hot industrial liquids should not be pumped unless specifically approved by the manufacturer.
Liquid pH Range – 6.5 to 8
The QDX series is specified for liquids with a pH range of 6.5–8.
This corresponds generally to relatively neutral water.
Strongly acidic or alkaline liquids may damage the pump's wetted components, seals or metal parts and should not be pumped without manufacturer approval.
Sewage and Wastewater Suitability
Although the product is commonly listed by Malaysian retailers as a “Submersible Sewage Pump”, LEO's technical documentation describes the QDX range primarily for irrigation, drainage, well-water pumping, accumulated-water drainage and aquaculture.
Therefore, the QDX 10-18-1.1A should be considered a drainage/water-transfer submersible pump, rather than a heavy-duty raw-sewage pump.
It is appropriate for relatively clean water and lightly contaminated drainage water. It is not the correct choice for wastewater containing:
- Large solids
- Rags
- Rope
- Fibres
- Plastic waste
- Stones
- Thick sludge
- Large organic matter
For heavy sewage, a dedicated non-clog sewage pump with a substantially larger solids passage should be selected.
Suitable Applications
The QDX series is intended for small electrical irrigation and drainage equipment, rural/urban well-water pumping, field irrigation and drainage, garden irrigation, household water supply, industrial accumulated-water drainage, construction water drainage and livestock applications.
Agricultural Applications
- Farm irrigation
- Field drainage
- Well-water transfer
- Garden irrigation
- Orchard water transfer
- Water supply for farming
Construction Applications
- Excavation dewatering
- Foundation drainage
- Construction-site drainage
- Basement water removal
- Temporary dewatering
Residential Applications
- Garden irrigation
- Pond drainage
- Water tank transfer
- Well-water transfer
- Household water supply
Industrial Applications
- Accumulated-water drainage
- Equipment-area drainage
- General water transfer
- Utility water drainage
Livestock and Aquaculture
- Livestock water transfer
- Fish ponds
- Small aquaculture systems
- Tank drainage
- Water circulation and transfer
Recommended Discharge Setup
A typical installation can be arranged as:
Well / Pond / Drainage Pit → LEO QDX 10-18-1.1A → 2" Discharge Hose/Pipe → Tank / Irrigation System / Drainage Point
The pump should be installed vertically in the water source, with adequate clearance around the inlet and sufficient space for the float switch to move freely.
A properly sized 2-inch discharge hose is recommended to minimise unnecessary friction losses.
Installation Recommendations
For reliable operation:
- Do not exceed the 5 m maximum immersion depth.
- Use the pump only with a suitable 220 V supply.
- Ensure proper electrical grounding.
- Use an appropriate circuit breaker and electrical protection.
- Do not lift the pump by the power cable.
- Use a rope or suitable lifting arrangement.
- Keep the intake area free from excessive debris.
- Keep the float switch unobstructed.
- Avoid heavy sediment accumulation.
- Use a suitable 2-inch discharge hose.
- Minimise unnecessary bends and restrictions.
- Do not operate the pump outside its specified liquid temperature and pH range.
Main Product Advantages
- 1.1 kW / 1.5 HP motor.
- 220 V single-phase operation.
- Automatic float-switch operation.
- Up to approximately 275 L/min flow.
- Approximately 16.5 m³/h maximum flow.
- Up to approximately 25.5–25.8 m maximum head.
- 2-inch / 50 mm discharge outlet.
- Cast-iron HT200 pump body.
- Stainless-steel shaft.
- PPO/ZL102 impeller.
- Carbon/ceramic mechanical seal.
- Copper motor winding.
- Built-in thermal protection.
- Class B insulation.
- IP68 protection.
- Maximum immersion depth of 5 m.
- Maximum liquid temperature of 40°C.
- Suitable for irrigation and drainage.
- Suitable for well-water and pond water transfer.
- Suitable for construction dewatering and accumulated-water drainage.
Product Details Summary
The LEO QDX 10-18-1.1A is a 1.1 kW / 1.5 HP automatic single-phase submersible drainage pump designed for irrigation, drainage, well-water transfer, construction dewatering, garden irrigation, livestock applications and general water transfer. It operates at 220 V and features a 2-inch / 50 mm outlet, with a published hydraulic range of approximately 25–275 L/min and 25.5–4 m head.
The pump incorporates a cast-iron HT200 body, stainless-steel shaft, PPO/ZL102 impeller, carbon/ceramic mechanical seal, copper winding, built-in thermal protection, Class B insulation and IP68 protection. It is suitable for liquid temperatures up to 40°C, pH 6.5–8, and a maximum immersion depth of 5 m.
The automatic float switch allows convenient water-level-based operation, making the pump particularly useful for drainage pits, sumps, tanks and other applications where automatic starting and stopping is required.
SEO Product Title
LEO QDX 10-18-1.1A Automatic Submersible Drainage Pump 1.5HP 1.1kW – 25.8M Head, 2" Outlet
SEO Product Description
LEO QDX 10-18-1.1A Automatic Submersible Drainage Pump is a powerful 1.5HP / 1.1kW, 220V single-phase submersible pump designed for irrigation, drainage, well-water transfer, construction dewatering, garden irrigation, livestock applications and general water transfer. Equipped with an automatic float switch and 2-inch / 50mm discharge outlet, the pump delivers approximately 25–275L/min flow with a maximum head of approximately 25.5–25.8 metres. The pump features a durable HT200 cast-iron body, stainless-steel shaft, PPO/ZL102 impeller and carbon/ceramic mechanical seal, together with copper motor winding, built-in thermal protection, Class B insulation and IP68 protection. With a maximum immersion depth of 5 metres and maximum liquid temperature of 40°C, the LEO QDX 10-18-1.1A provides a reliable solution for wells, ponds, drainage pits, construction sites, agricultural irrigation and accumulated-water removal.
Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - QDX 10-18-1.1A