The LEO QDX 15-14-1.1A is a 1.1 kW / 1.5 HP, 220 V single-phase submersible drainage pump designed for high-volume water transfer, irrigation, drainage, well-water pumping, construction dewatering, aquaculture and general water removal. LEO's QDX-LA specification lists 25–500 L/min flow, 14.9–3.1 m head, 65 mm outlet and 5 m maximum immersion depth for this model.
It is worth noting that although this model is commonly marketed under the sewage submersible pump category, the QDX-LA is technically a submersible drainage pump for clean or lightly contaminated water. LEO specifies a suspended-solids passage of approximately 0.2 mm and maximum sand content of 0.1%, so it is not intended for heavy raw sewage containing rags, ropes, large solids or fibrous waste.
Product Specifications
| Specification | Details |
|---|---|
| Brand | LEO |
| Model | QDX 15-14-1.1A |
| Series | QDX-LA |
| Pump Type | Submersible Drainage Pump |
| Motor Power | 1.1 kW |
| Motor Rating | 1.5 HP |
| Voltage | 220 V |
| Frequency | 50 Hz |
| Phase | Single Phase |
| Maximum Flow | Approx. 500 L/min |
| Maximum Flow | Approx. 30 m³/h |
| Head Range | Approx. 14.9–3.1 m |
| Maximum Head | Approx. 15 m |
| Rated Capacity | Approx. 15 m³/h |
| Rated Head | Approx. 14 m |
| Outlet Size | 65 mm / 2½" |
| Maximum Immersion Depth | 5 m |
| Maximum Liquid Temperature | 40°C |
| Liquid pH Range | 6.5–8 |
| Maximum Sand Content | 0.1% |
| Suspended-Solid Passage | Approx. 0.2 mm |
| Pump Body | Cast Iron |
| Motor Casing | Aluminium |
| Shaft | Stainless Steel |
| Impeller | Engineering Polymer |
| Mechanical Seal | Double-End Mechanical Seal |
| Motor Winding | Copper |
| Insulation Class | F |
| Protection Class | IP68 |
| Thermal Protection | Built-In |
| Installation | Vertical / Submersible |
LEO's QDX-LA catalogue specifies 220 V, 25–500 L/min, 14.9–3.1 m head, 5 m immersion depth, 1.1 kW / 1.5 HP and 65 mm outlet for the QDX 15-14-1.1A.
A Malaysian distributor likewise lists the model as 1.1 kW, 220 V, 50 Hz, 2½-inch discharge, with approximately 25–525 L/min and 16.6–4.3 m head; this represents a slightly different published performance reference. For catalogue purposes, the LEO specification should be treated as the primary reference.
1.1 kW / 1.5 HP Motor
The QDX 15-14-1.1A uses a 1.1 kW / 1.5 HP single-phase motor operating at 220 V, 50 Hz. This power rating provides a useful combination of flow capacity and moderate lifting head for drainage and water-transfer applications.
The motor is suitable for applications where water must be transferred over a moderate vertical distance while maintaining substantial flow.
Typical applications include:
- Agricultural irrigation
- Farm drainage
- Well-water pumping
- Pond drainage
- Construction dewatering
- Industrial accumulated-water drainage
- Aquaculture
- Tank emptying
- General water transfer
High-Volume Water Flow
The QDX 15-14-1.1A is designed primarily for high-volume water movement.
LEO specifies a flow range of approximately:
25–500 L/min
which corresponds to approximately:
1.5–30 m³/h
The maximum flow occurs at low system head. As the required head increases, the available flow decreases.
A separate performance table gives the following approximate operating points:
| Flow | Approx. Head |
|---|---|
| 25 L/min | 14.9 m |
| 50 L/min | 14.8 m |
| 100 L/min | 14.6 m |
| 150 L/min | 14.3 m |
| 200 L/min | 14.0 m |
| 250 L/min | 13.8 m |
| 300 L/min | 12.5 m |
| 350 L/min | 10.6 m |
| 400 L/min | 8.0 m |
| 450 L/min | 5.5 m |
| 475 L/min | 4.4 m |
| 500 L/min | 3.1 m |
These figures illustrate that the pump provides considerably more flow when the discharge system has relatively low resistance.
Approximately 15 m Maximum Head
The QDX 15-14-1.1A has a maximum head of approximately 15 m according to LEO's specification. The catalogue gives a performance range of approximately 14.9–3.1 m across its published flow range.
The “14” in the model designation corresponds broadly to its rated hydraulic class of approximately 14 m head, rather than representing its absolute shut-off head.
A technical listing gives approximately 15 m maximum head and 15 m³/h rated capacity at 14 m head, which aligns with the model designation.
Actual operating head will depend on:
- Vertical lift
- Pipe length
- Pipe diameter
- Hose diameter
- Number of elbows
- Valves
- Check valves
- Friction losses
- Required flow
65 mm / 2½-Inch Discharge
The QDX 15-14-1.1A has a 65 mm / 2½-inch discharge outlet. LEO's catalogue specifies a 65 mm outlet for this model.
The relatively large outlet complements the pump's high-flow capability.
It is suitable for:
- Large drainage hoses
- Construction dewatering lines
- Agricultural irrigation
- Pond drainage
- Water-transfer systems
- Tank filling
- Aquaculture applications
A correctly sized discharge hose helps minimise friction losses and allows the pump to deliver better hydraulic performance.
Cast-Iron Pump Body
The pump uses a cast-iron pump body. The QDX-LA series is specified with a cast-iron body and aluminium motor casing.
The cast-iron construction provides:
- Good mechanical strength
- Durable pump housing
- Resistance to normal mechanical impacts
- Stable support for the hydraulic components
- Suitability for drainage applications
Aluminium Motor Casing
The QDX-LA construction incorporates an aluminium motor casing.
Aluminium helps dissipate motor heat while keeping the pump relatively manageable for portable drainage applications.
This is useful where the pump is regularly moved between:
- Construction sites
- Farms
- Ponds
- Drainage areas
- Water tanks
Stainless-Steel Shaft
The QDX 15-14-1.1A incorporates a stainless-steel shaft.
The shaft is an important rotating component operating in the wet pump environment.
The stainless-steel construction provides:
- Corrosion resistance
- Good mechanical strength
- Reliable rotation
- Better durability in submerged applications
Engineering-Polymer Impeller
The QDX-LA design uses an engineering-polymer impeller.
The impeller converts the motor's rotational energy into hydraulic energy, generating the flow and pressure required for water transfer.
The pump should not be used with large debris, stones, ropes, rags or fibrous material that can obstruct the hydraulic passage.
Double-End Mechanical Seal
The QDX-LA series features a double-end mechanical seal.
The mechanical seal protects the motor compartment from the pumped liquid around the rotating shaft.
This is particularly important for a submersible pump because the pump operates directly inside the water.
Copper Motor Winding
The QDX 15-14-1.1A uses copper motor winding. LEO's product information identifies copper winding for the QDX series.
Copper provides good electrical conductivity and suitable thermal characteristics for the 1.1 kW motor.
Built-In Thermal Protection
The pump incorporates a built-in thermal protector.
The thermal protection helps protect the motor against excessive temperature under abnormal operating conditions.
However, the installation should still include suitable:
- Circuit breaker
- Electrical isolation
- Grounding
- Correct cable sizing
- Appropriate electrical protection
Class F Insulation
The QDX-LA series is specified with Class F motor insulation.
The insulation system helps protect the motor winding against thermal stress under the manufacturer's specified operating conditions.
IP68 Protection
The pump is rated IP68, making it suitable for submerged operation.
This is appropriate for applications such as:
- Wells
- Drainage pits
- Ponds
- Water tanks
- Construction excavations
- Flooded areas
- Agricultural water sources
The IP68 rating should be considered together with the specified 5 m maximum immersion depth.
Maximum Immersion Depth – 5 m
The maximum specified immersion depth is 5 metres.
For safe installation:
- Do not exceed 5 m immersion depth.
- Do not lift the pump using the electrical cable.
- Use a suitable rope or lifting arrangement.
- Keep the pump securely positioned.
- Prevent the inlet from becoming buried in mud or heavy sediment.
Maximum Liquid Temperature – 40°C
The QDX-LA series is specified for a maximum liquid temperature of 40°C.
The pump is intended for normal-temperature water and compatible drainage liquids.
Suitable liquids include:
- Fresh water
- Rainwater
- Well water
- Irrigation water
- Pond water
- Lightly contaminated drainage water
Hot industrial liquids should not be pumped unless specifically approved by the manufacturer.
Liquid pH Range – 6.5 to 8
LEO specifies a pH range of 6.5–8 for the QDX-LA series.
The pump is therefore primarily intended for relatively neutral water.
Strongly acidic or alkaline liquids may damage the mechanical seal and wetted components.
Sand and Suspended Solids
The QDX-LA series permits approximately 0.1% maximum sand content and suspended solids up to approximately 0.2 mm.
This allows the pump to handle some lightly contaminated drainage water, but it is not a large-solids sewage pump.
Avoid pumping:
- Large stones
- Gravel
- Rags
- Rope
- Plastic waste
- Fibres
- Thick sludge
- Large organic solids
- Construction debris
Sewage Application Limitation
Although the model may be categorised by retailers as a sewage submersible pump, LEO's own QDX documentation describes this series for irrigation, drainage, well-water pumping, accumulated-water drainage, construction and aquaculture.
Therefore, for accurate website classification, it is better described as:
Submersible Drainage / Water Transfer Pump
rather than a heavy-duty raw-sewage pump.
For sewage containing significant quantities of solids, rags or fibrous material, a dedicated non-clog sewage pump should be selected.
Suitable Applications
LEO identifies the QDX range for irrigation and drainage equipment, well-water pumping, field irrigation, garden irrigation, household water supply, industrial accumulated-water drainage, construction water drainage, livestock and aquaculture applications.
Agricultural
- Farm irrigation
- Field drainage
- Well-water pumping
- Orchard irrigation
- Garden watering
- Agricultural water transfer
Construction
- Excavation dewatering
- Foundation drainage
- Construction-site water removal
- Basement drainage
- Temporary dewatering
Residential
- Pond drainage
- Tank emptying
- Garden irrigation
- Well-water transfer
- General water transfer
Industrial
- Accumulated-water drainage
- Utility water transfer
- Industrial drainage
- Equipment-area water removal
Aquaculture
- Fish pond drainage
- Water transfer
- Tank emptying
- Small aquaculture installations
High-Volume Drainage Performance
The QDX 15-14-1.1A is particularly suited to applications where large water volume and moderate head are required.
Its combination of:
1.1 kW motor + 65 mm outlet + up to approximately 500 L/min
makes it appropriate for larger drainage systems than smaller QDX models.
For example, it can be used for removing accumulated water from a construction excavation, transferring water from a pond, or moving irrigation water from a collection point.
Typical Installation
A typical installation can be arranged as:
Pond / Well / Drainage Pit → LEO QDX 15-14-1.1A → 2½" Discharge Hose/Pipe → Drainage Area / Tank / Irrigation System
The pump is submerged directly into the water source.
The discharge pipe or hose should be adequately supported so that its weight is not transferred directly to the pump outlet.
Installation Recommendations
For reliable operation:
- Use a suitable 220 V single-phase supply.
- Do not exceed the 5 m immersion depth.
- Use a properly sized 65 mm / 2½" discharge line.
- Minimise unnecessary bends and restrictions.
- Keep the pump inlet clear.
- Avoid placing the pump directly into heavy sediment.
- Do not lift the pump by its electrical cable.
- Use a rope or suitable lifting system.
- Ensure proper electrical grounding.
- Use appropriate circuit protection.
- Keep the pump within the specified liquid temperature and pH range.
- Inspect the mechanical seal and cable periodically.
- Ensure sufficient water around the pump during operation.
Main Product Advantages
- 1.1 kW / 1.5 HP motor.
- 220 V single-phase operation.
- High-volume water transfer capability.
- Up to approximately 500 L/min according to LEO's catalogue.
- Up to approximately 30 m³/h published flow.
- Approximately 15 m maximum head.
- Approximately 14 m rated head.
- Large 65 mm / 2½" outlet.
- Cast-iron pump body.
- Aluminium motor casing.
- Stainless-steel shaft.
- Engineering-polymer impeller.
- Double-end mechanical seal.
- Copper motor winding.
- Built-in thermal protection.
- Class F insulation.
- IP68 protection.
- Maximum immersion depth of 5 m.
- Maximum liquid temperature of 40°C.
- Suitable for irrigation, drainage, construction and aquaculture.
Product Details Summary
The LEO QDX 15-14-1.1A is a 1.1 kW / 1.5 HP, 220 V single-phase submersible drainage pump designed for high-volume water transfer, agricultural irrigation, well-water pumping, construction dewatering, pond drainage, aquaculture and general drainage applications. LEO specifies approximately 25–500 L/min flow, 14.9–3.1 m head, 65 mm outlet and 5 m maximum immersion depth.
The pump features a cast-iron body, aluminium motor casing, stainless-steel shaft, engineering-polymer impeller and double-end mechanical seal, supported by copper winding, built-in thermal protection, Class F insulation and IP68 protection. It is suitable for liquids up to 40°C, with a specified pH range of 6.5–8.
With its 1.1 kW motor and 2½-inch discharge, the QDX 15-14-1.1A is well suited to applications requiring substantial water volume at moderate head. Its rated hydraulic class is approximately 15 m³/h at 14 m head, while the maximum published flow reaches approximately 30 m³/h at low head.
SEO Product Title
LEO QDX 15-14-1.1A Submersible Drainage Pump 1.5HP 1.1kW – 15M Head, 2½" Outlet
SEO Product Description
LEO QDX 15-14-1.1A Submersible Drainage Pump is a powerful 1.5HP / 1.1kW, 220V single-phase pump designed for high-volume water drainage, agricultural irrigation, well-water pumping, construction dewatering, pond drainage, aquaculture and general water transfer. Equipped with a large 65mm / 2½-inch discharge outlet, the pump provides approximately 25–500L/min flow with a maximum head of approximately 15 metres according to LEO's QDX-LA specifications. The pump features a durable cast-iron body, aluminium motor casing, stainless-steel shaft, engineering-polymer impeller and double-end mechanical seal, together with copper motor winding, built-in thermal protection, Class F insulation and IP68 protection. With a maximum immersion depth of 5 metres and maximum liquid temperature of 40°C, the LEO QDX 15-14-1.1A is a practical solution for agricultural drainage, irrigation, construction sites, ponds, wells, tanks and aquaculture applications.
Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - QDX 15-14-1.1A