B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO SUBMERSIBLE PERIPHERAL PUMPS - SPM 37 (MANUAL)



The LEO SPM37 is a compact 0.5 HP (0.37 kW) single-phase submersible peripheral pump designed for clean-water transfer, small-scale water supply, garden irrigation, pressure boosting and general domestic, agricultural and light construction applications. Unlike the SPM37A, the SPM37 is the manual/non-automatic version and does not use a float switch. Malaysian product listings identify the SPM37 as a 220 V, 0.5 HP pump with a 1-inch outlet and a maximum head of approximately 35 m.

Product Description

The LEO SPM37 combines the compact installation advantages of a submersible pump with the high-head characteristics of a peripheral pump. It can be placed directly into the water source, eliminating the need for a conventional suction line and allowing the pump to transfer water to elevated or pressurized applications.

The pump is powered by a 0.37 kW / 0.5 HP single-phase motor and operates from a 220 V supply. Its peripheral hydraulic design provides comparatively high pressure from a small motor, with published performance data showing approximately 5.4–38.1 L/min flow and 35–0.5 m head in a Malaysian listing.

LEO's technical documentation specifies the SPm series for clean water or liquids with similar physical and chemical properties. Typical applications include small domestic water supply, garden irrigation, automatic sprinkler systems and supporting equipment.

Key Specifications

Specification LEO SPM37
Brand LEO
Model SPM37
Pump Type Submersible Peripheral Pump
Operation Manual / Non-Automatic
Motor Power 0.37 kW / 0.5 HP
Motor Type Single Phase
Voltage 220 V
Frequency 50 Hz
Maximum Flow Approx. 38.1 L/min
Maximum Flow Approx. 2.3 m³/h
Maximum Head Approx. 35 m
Minimum Head Approx. 0.5 m
Outlet 1 inch
Maximum Immersion Depth 5 m
Maximum Liquid Temperature Approx. 40°C
Protection IPX8 / IP68 depending on documentation/version
Insulation Class F
Motor Winding Copper
Pump Type Peripheral
Impeller Brass
Shaft Steel / stainless-steel construction depending on specification version
Speed Approx. 2,850 rpm
Float Switch No
Automatic Operation No

The LEO documentation gives the SPm37 a 0.37 kW rating, with hydraulic performance reaching approximately 41.4 L/min at zero head in one published technical curve, while Malaysian retail specifications quote 38.1 L/min maximum flow and 35 m maximum head. Performance figures should therefore be treated as catalogue/curve values and actual operating flow will depend on system resistance.

Hydraulic Performance

The main advantage of the SPM37 is its ability to generate relatively high head from a compact 0.5 HP peripheral pump.

Published data indicates approximately:

  • Maximum head: up to 35 m
  • Flow at maximum head: approximately 5.4–8 L/min, depending on the catalogue/version
  • Around 20 m head: approximately 16.7–20 L/min
  • Around 10 m head: approximately 25 L/min
  • Maximum flow: approximately 33–38.1 L/min depending on the published specification/curve

The hydraulic curve should be used for final pump selection because flow decreases as discharge head increases. The pump should not be selected solely on its advertised maximum flow or maximum head.

Motor Features

0.5 HP Single-Phase Motor
The 0.37 kW motor provides a practical balance between electrical consumption and pressure generation for small domestic and agricultural applications.

Copper Motor Winding
The LEO SPm documentation specifies a copper-wound motor, providing good electrical conductivity and heat dissipation.

Built-In Capacitor
The single-phase motor incorporates a capacitor for motor starting and operation.

Continuous-Duty Design
The SPm series is designed around a two-pole induction motor suitable for continuous service within its specified operating conditions.

Thermal Protection
The motor design incorporates protection against excessive temperature, helping reduce the risk of motor damage under abnormal operating conditions.

Pump Construction

The SPM37 uses a cast-iron pump body with anti-rust treatment, while the motor casing is designed for submerged operation. LEO's published material information for the SPm series identifies HT200 cast iron for the pump body, a brass impeller, and a carbon/ceramic mechanical seal.

The peripheral impeller is designed to produce relatively high pressure from a compact pump body, making the SPM37 more appropriate for high-head/low-to-moderate-flow applications than for high-volume drainage.

Protection & Operating Conditions

The SPM37 is intended for submerged operation and LEO documentation specifies:

  • Maximum immersion depth: 5 m
  • Maximum liquid temperature: approximately 35–40°C depending on the catalogue version
  • Liquid pH: approximately 6.5–8.5
  • Maximum sand content: 0.1%
  • Maximum solid particle diameter: approximately 0.2 mm
  • Protection: IPX8/IP68 depending on documentation/version
  • Insulation: Class F

These specifications indicate that the pump is intended primarily for clean water, rather than sewage, slurry, abrasive wastewater or heavily contaminated liquids.

Manual Operation

The SPM37 (Manual) differs from the SPM37A automatic model mainly in its operating configuration.

The manual SPM37 is supplied without a float switch, meaning the user or an external control system must control the pump's start/stop operation. The SPM37A, by comparison, is equipped with a float switch for automatic level-based operation. Malaysian listings explicitly identify the SPM37 as “non-auto” and “without floating switch.”

This makes the SPM37 suitable where:

  • An external pump controller is already installed.
  • Manual switching is preferred.
  • The pump is operated only when required.
  • An external float/level controller will be used.
  • The installation requires a simpler pump configuration.

Recommended Applications

The LEO SPM37 is suitable for:

  • Domestic clean-water transfer
  • Small household water-supply systems
  • Garden irrigation
  • Small sprinkler systems
  • Water transfer from wells or tanks
  • Small pressure-boosting applications
  • Agricultural water transfer
  • Small construction water-supply applications
  • Watering systems
  • Supporting equipment requiring a compact water pump
  • Temporary clean-water pumping
  • Elevated water transfer where moderate-to-high head is required

LEO specifically identifies the SPm series for clean-water transfer, small living-water supply, automatic sprinkler systems and related equipment. Other LEO catalogue material also identifies domestic, construction and agricultural water-supply applications.

Advantages

  1. Compact 0.5 HP design – Suitable for small water-supply installations.
  2. High head capability – Up to approximately 35 m, depending on operating conditions.
  3. Submersible installation – Pump operates directly inside the water source.
  4. Peripheral hydraulic design – Provides higher pressure than many conventional low-head pumps of similar power.
  5. Manual configuration – No integrated float switch, allowing external control.
  6. 1-inch outlet – Convenient for common domestic and irrigation piping systems.
  7. IPX8/IP68 protection – Designed for submerged operation.
  8. Copper motor winding – Provides reliable motor performance.
  9. Brass peripheral impeller – Suitable for clean-water pumping.
  10. Cast-iron pump construction – Provides mechanical durability.
  11. Built-in capacitor – Designed for single-phase operation.
  12. Clean-water applications – Suitable for domestic, garden and small agricultural water transfer.

SPM37 vs SPM37A

Feature SPM37 Manual SPM37A Automatic
Motor 0.37 kW / 0.5 HP 0.37 kW / 0.5 HP
Voltage 220 V 220 V
Pump Type Submersible Peripheral Submersible Peripheral
Float Switch No Yes
Operation Manual / external control Automatic level control
Outlet 1" 1"
Maximum Head Approx. 35 m Approx. 35 m
Maximum Flow Approx. 38 L/min Approx. 30–33 L/min depending on published version
Best For Manual/external-control systems Automatic water-level operation

The two models belong to the same SPm family, but the “A” designation identifies the automatic float-switch configuration.

Product Technical Data

Brand: LEO
Model: SPM37
Product Category: Submersible Peripheral Pump
Operation: Manual / Non-Automatic
Motor Power: 0.37 kW / 0.5 HP
Voltage: 220 V
Frequency: 50 Hz
Phase: Single Phase
Maximum Flow: Approx. 38.1 L/min
Maximum Head: Approx. 35 m
Maximum Immersion: 5 m
Outlet: 1 inch
Motor Speed: Approx. 2,850 rpm
Insulation Class: F
Protection: IPX8/IP68
Maximum Water Temperature: Approx. 40°C
Suitable Liquid: Clean water
Float Switch: Not included
Impeller Type: Peripheral
Impeller Material: Brass
Pump Body: Cast Iron with anti-rust treatment
Mechanical Seal: Carbon/Ceramic
Motor Winding: Copper
Application: Domestic, irrigation, water transfer and light-duty water supply

SEO Product Description

LEO SPM37 0.5HP Manual Submersible Peripheral Pump is a compact high-head water pump designed for clean-water transfer, domestic water supply, garden irrigation, sprinkler systems, agricultural applications and small water-boosting systems. Powered by a 0.37 kW (0.5 HP) 220 V single-phase motor, the SPM37 delivers up to approximately 38.1 L/min with a maximum head of around 35 m. Its peripheral pump design provides high pressure from a compact motor, while the submersible configuration allows direct installation inside a water source. The pump features a durable cast-iron pump body, brass impeller, copper motor winding, built-in capacitor and IPX8/IP68-class submerged protection. The manual SPM37 is supplied without a float switch, making it suitable for installations using manual operation or an external level/pump control system.



 Inquiry - LEO SUBMERSIBLE PERIPHERAL PUMPS - SPM 37 (MANUAL)