B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO SUBMERSIBLE PERIPHERAL PUMPS - SPM 37A (AUTO)



The LEO SPM37A is a compact 0.5 HP (0.37 kW) automatic submersible peripheral pump designed for clean-water transfer, small domestic water supply, garden irrigation, well-water lifting, sprinkler systems and pressure-boosting applications. The key difference from the SPM37 manual version is the integrated float switch, which provides automatic pump start/stop according to the water level. LEO identifies the SPm series for clean water and applications such as small domestic water supply and automatic sprinkler systems.

Product Description

The LEO SPM37A combines a submersible installation with a peripheral hydraulic design. Its 0.37 kW / 0.5 HP single-phase motor is suitable for installations where a compact pump is required but relatively high delivery head is still needed.

The LEO technical documentation gives the SPM37A a hydraulic performance range reaching approximately 33.4 L/min at zero head and 40 m maximum head. Malaysian listings commonly specify the practical operating range as 5.4–38.1 L/min with 35–0.5 m head, so the exact published figures can vary slightly by catalogue generation and market specification.

The “A” designation indicates automatic operation with a float switch. When the water level changes, the float switch can automatically control pump cut-in and cut-out, reducing the need for manual switching.

Key Specifications

Specification LEO SPM37A
Brand LEO
Model SPM37A
Pump Type Submersible Peripheral Pump
Operation Automatic
Automatic Control Float Switch
Motor Power 0.37 kW / 0.5 HP
Motor Single Phase
Voltage 220 V / 180–220 V depending on specification
Frequency 50 Hz
Rated Current Approx. 2.5 A
Maximum Flow Approx. 33–38.1 L/min
Maximum Head Approx. 35–40 m
Rated Flow Range Approx. 5–30 L/min
Rated Head Range Approx. 36–3 m
Outlet 1 inch
Maximum Immersion 3–5 m depending on specification
Maximum Liquid Temperature +40°C
Liquid pH 6.5–8 / 6.5–8.5
Maximum Sand Content 0.1%
Maximum Solid Diameter 0.2 mm
Speed Approx. 2,850 rpm
Protection IPX8
Insulation Class F
Motor Winding Copper
Impeller Brass
Pump Body HT200 Cast Iron
Mechanical Seal Carbon/Ceramic
Capacitor 8 μF / 450 V
Automatic Device Float Switch
Duty Continuous duty / thermally protected

Published LEO documentation specifies 0.37 kW / 0.5 HP, IPX8 protection, Class F insulation, copper winding, brass impeller, carbon/ceramic mechanical seal and automatic operation with a float switch.

Automatic Float-Switch Operation

The main selling feature of the SPM37A is its automatic float-switch system.

When the water level rises to the appropriate level, the float changes position and allows the pump to start. As the water level falls, the float moves back and disconnects the pump. This makes the SPM37A particularly useful for applications where the pump needs to respond automatically to changing water levels.

Typical applications include:

  • Water tanks
  • Small wells
  • Sumps
  • Garden irrigation
  • Automatic sprinkler systems
  • Small drainage applications
  • Water transfer systems
  • Domestic water supply
  • Temporary water-taking applications

The float switch is specifically identified in LEO's technical documentation as providing automatic operation.

Hydraulic Performance

The SPM37A is a peripheral pump, so it is designed to provide relatively high head from a small motor rather than extremely high flow.

The published LEO hydraulic curve indicates approximately:

Flow Approx. Head
0 L/min 40 m
8.35 L/min 30 m
16.7 L/min 20 m
25.05 L/min 10 m
33.4 L/min 0 m

These figures are based on LEO's published SPM37A performance data. Actual system flow will be lower or higher depending on piping length, pipe diameter, fittings, elevation and other system resistance.

This performance makes the SPM37A particularly useful when the installation requires moderate flow with relatively high pressure/head.

Motor & Electrical Features

0.37 kW / 0.5 HP Motor
The compact single-phase motor provides sufficient power for small domestic, irrigation and water-transfer applications.

Copper Winding
The motor uses copper windings for reliable electrical conductivity and heat dissipation.

Built-In Thermal Protection
The motor is thermally protected to help prevent damage caused by excessive temperature during abnormal operating conditions.

Class F Insulation
Class F insulation provides suitable thermal resistance for the motor winding system.

IPX8 Protection
The IPX8 enclosure rating is intended for continuous submerged operation within the manufacturer's specified conditions.

8 μF / 450 V Capacitor
Published specifications for the SPM37A identify an 8 μF / 450 V capacitor for the single-phase motor.

Pump Construction

The SPM37A uses a robust construction intended for submerged clean-water pumping.

Cast-Iron Pump Body: LEO specifies special anti-rust treatment for the cast-iron pump body and support.

Brass Impeller: The peripheral impeller is made from brass according to the published material table.

Carbon/Ceramic Mechanical Seal: This provides sealing between the rotating shaft and pump body to help prevent water from entering the motor section.

AISI 304 Shaft: Some current regional listings specify an AISI 304 stainless-steel shaft for the SPM37 family.

Operating Conditions

The SPM37A is designed primarily for clean water or liquids with similar physical and chemical properties. LEO specifies the following operating limitations:

  • Maximum liquid temperature: approximately 40°C
  • Maximum immersion depth: 3–5 m, depending on the published version
  • Liquid pH: approximately 6.5–8.5
  • Maximum sand content: 0.1%
  • Maximum solid particle diameter: 0.2 mm
  • Protection class: IPX8
  • Insulation class: F

Because this is a peripheral clean-water pump, it should not be treated as a sewage or heavy-duty wastewater pump. Abrasive sand, mud, sludge and large suspended solids can cause premature wear or blockage.

Recommended Applications

The LEO SPM37A is suitable for:

  1. Small domestic water supply – Transfers water from tanks or suitable water sources.
  2. Garden irrigation – Suitable for watering systems requiring moderate pressure.
  3. Automatic sprinkler systems – The automatic float switch provides convenient water-level control.
  4. Well-water lifting – Suitable for lifting clean water from appropriate shallow sources.
  5. Water tank transfer – Can automatically operate according to water level.
  6. Pressure boosting – Suitable for small water-transfer/boosting applications.
  7. Temporary water taking – Compact construction allows easy installation and relocation.
  8. Small air-conditioning support systems – LEO identifies supporting equipment as one of the SPm applications.

SPM37A vs SPM37

Feature SPM37A Auto SPM37 Manual
Motor Power 0.37 kW / 0.5 HP 0.37 kW / 0.5 HP
Voltage 220 V 220 V
Pump Type Submersible Peripheral Submersible Peripheral
Float Switch Yes No
Operation Automatic Manual
Max. Head Approx. 35–40 m Approx. 35 m
Max. Flow Approx. 33–38.1 L/min Approx. 38.1 L/min
Outlet 1" 1"
Protection IPX8 IPX8
Best Use Automatic water-level control External/manual control

The SPM37A is essentially the automatic float-switch version, while the SPM37 is the non-automatic version. Malaysian product listings explicitly identify the SPM37A as “with floating switch” and the SPM37 as “without floating switch.”

Dimensions & Weight

LEO's published technical data gives the SPM37A approximately:

  • Outlet: 1 inch
  • Overall length (L): 170 mm
  • L1: 106 mm
  • Height (H): 244 mm
  • Width (W): 118 mm
  • Gross packaged weight: approximately 7.56 kg
  • Package dimensions: approximately 184 × 135 × 300 mm

The compact dimensions make the pump convenient for installation in relatively confined tanks, wells and water containers.

Product Advantages

  • Automatic float-switch operation
  • 0.5 HP compact motor
  • High head performance up to approximately 35–40 m
  • Flow up to approximately 33–38.1 L/min
  • Submersible installation
  • 1-inch discharge outlet
  • Brass peripheral impeller
  • Copper motor winding
  • Cast-iron pump body with anti-rust treatment
  • Carbon/ceramic mechanical seal
  • IPX8 protection
  • Class F insulation
  • Built-in thermal protection
  • Suitable for clean-water applications
  • Suitable for domestic and garden irrigation
  • Automatic start/stop through float switch
  • Compact and easy to install

Important Selection Note

The SPM37A should be selected based on the required operating head and flow, not simply the advertised maximum values. For example, the pump can reach around 33.4 L/min near zero head, but the flow falls substantially as head increases. At approximately 20 m head, the published curve indicates around 16.7 L/min.

For a system with long pipe runs, many elbows, elevated tanks or high discharge points, the actual flow should therefore be checked against the pump curve.

SEO Product Description

LEO SPM37A 0.5HP Auto Submersible Peripheral Pump is a compact automatic water pump designed for clean-water transfer, domestic water supply, garden irrigation, well-water lifting, automatic sprinkler systems and small water-boosting applications. Powered by a 0.37 kW / 0.5 HP single-phase motor, the SPM37A provides high-head performance of up to approximately 35–40 metres with maximum flow of around 33–38.1 L/min, depending on operating conditions and specification version. The pump features a built-in float switch for automatic start/stop operation, copper motor winding, brass peripheral impeller, cast-iron pump body with anti-rust treatment, carbon/ceramic mechanical seal, Class F insulation and IPX8 protection. With its compact submersible design and automatic water-level control, the LEO SPM37A is an effective choice for small domestic water systems, garden irrigation, tanks, wells and clean-water transfer applications.



 Inquiry - LEO SUBMERSIBLE PERIPHERAL PUMPS - SPM 37A (AUTO)