The LEO LGP10 is a compact 1-inch gasoline engine water pump designed for transferring clean water in locations where electrical power is unavailable or impractical. It uses a single-cylinder, 2-stroke, air-cooled gasoline engine with a rated maximum output of 1.6 HP, paired with an efficient centrifugal pump. The unit is portable, compact and suitable for agricultural irrigation, gardening, construction-site water transfer, drainage and general water-supply applications.
The LGP10 has a maximum flow of approximately 100 L/min (6 m³/h) and a maximum head of approximately 35 m, with a maximum suction lift of 8 m. LEO's published performance curve shows the head decreasing from approximately 35 m at zero flow to approximately 6 m at 6 m³/h.
Product Description
The LEO LGP10 Gasoline Engine Pump is an entry-level portable water-transfer pump intended for applications requiring independent operation without an electrical supply.
Its gasoline engine drives a centrifugal impeller through a compact pump assembly. The pump uses a rust-resistant cast-iron impeller and diffuser, while the compact frame makes the unit relatively easy to transport and store. LEO specifies an efficient hydraulic system and low fuel consumption as key design characteristics.
The LGP10 is intended for clean water or liquids with similar physical and chemical properties, with a specified liquid temperature range of 0°C to 40°C.
Key Specifications
| Specification | LEO LGP10 |
|---|---|
| Brand | LEO |
| Model | LGP10 |
| Product Type | Gasoline Engine Water Pump |
| Engine Type | Single-Cylinder, 2-Stroke, Air-Cooled |
| Engine Model | G43 |
| Maximum Power | 1.6 HP / approx. 1.2 kW |
| Engine Displacement | 42.7 cc |
| Rated Speed | 7,500 rpm |
| Maximum Flow | 100 L/min |
| Maximum Flow | 6 m³/h |
| Maximum Head | 35 m |
| Maximum Suction | 8 m |
| Inlet | 1 inch / 25 mm |
| Outlet | 1 inch / 25 mm |
| Fuel Tank Capacity | 1.0 L |
| Fuel Mixture Ratio | 1:25 |
| Impeller | Anti-rust cast iron |
| Diffuser | Anti-rust cast iron |
| Pump Type | Centrifugal |
| Cooling | Air-cooled |
| Recommended Liquid | Clean water |
| Liquid Temperature | 0°C–40°C |
| Dimensions | Approx. 336 × 279 × 300 mm |
| Approx. Net Weight | 8.1 kg |
The 2026 LEO catalogue identifies the LGP10 as a 1.6 HP, 42.7 cc, G43, 2-stroke gasoline pump, with a 1 L fuel tank and 25 mm inlet/outlet.
Engine
The LGP10 uses a:
Single-cylinder, 2-stroke, air-cooled gasoline engine
with:
- 42.7 cc displacement
- 1.6 HP maximum power
- 7,500 rpm rated speed
- G43 engine designation
- 1.0 L fuel tank
- 1:25 fuel/oil mixture ratio.
The 2-stroke configuration provides a relatively high power-to-weight ratio, which is useful for a small portable engine pump.
Because this is a 2-stroke engine, the fuel must be prepared according to the manufacturer's specified 1:25 gasoline-to-2-stroke-oil mixture. The manufacturer specifies 90-octane or higher gasoline for the mixture.
Pump Construction
The hydraulic section incorporates an anti-rust cast-iron impeller and diffuser.
These components are designed to provide durability during repeated water-transfer operation while maintaining efficient hydraulic performance.
The pump is designed around a compact hydraulic system that provides a maximum flow of approximately 6 m³/h.
Flow Performance
The LGP10's maximum flow is approximately:
100 L/min = 6 m³/h
However, maximum flow and maximum head do not occur simultaneously.
According to the LEO performance data, the approximate operating points are:
| Flow | Approx. Head |
|---|---|
| 0 m³/h | 35 m |
| 2 m³/h | 32.5 m |
| 4 m³/h | 26.9 m |
| 6 m³/h | 6 m |
This means the pump can produce its highest head at very low flow, while the maximum 6 m³/h flow is available at substantially lower head.
For system selection, the actual flow should therefore be determined from the pump curve and the total system resistance.
Maximum Head
The LGP10 has a maximum head of approximately:
35 m
This is the pump's maximum developed head under the specified test conditions and should not be interpreted as the practical delivery height at maximum flow.
For example, LEO's published curve indicates approximately 26.9 m head at 4 m³/h, while the flow increases to approximately 6 m³/h at around 6 m head.
Maximum Suction
The maximum suction lift is:
8 m
LEO's documentation also indicates that approximately 5 m suction requires around 120 seconds for the pump to establish suction under the specified conditions.
Actual suction performance depends on:
- Suction-pipe length
- Pipe diameter
- Foot valve condition
- Air leakage
- Water temperature
- Pump priming
- Elevation
- Number of pipe fittings
The suction line should be airtight and appropriately sized.
1-Inch Inlet and Outlet
The LGP10 uses:
1" × 1" connections
with approximately 25 mm inlet/outlet dimensions.
This compact connection size makes the pump suitable for portable irrigation and water-transfer applications where a small-diameter hose or pipe system is appropriate.
Portable Design
The LGP10 is designed as a compact portable pump.
Its small engine and pump assembly make it suitable for moving between:
- Gardens
- Farms
- Construction sites
- Drainage areas
- Water tanks
- Temporary irrigation points
LEO specifically highlights its portable and compact construction, ergonomic design and low fuel consumption.
Three-Direction Adjustable Outlet
The LGP10 is equipped with a 3-direction adjustable outlet arrangement, allowing the discharge direction to be changed according to the installation requirements.
This can be useful for temporary water-transfer applications where the discharge hose needs to be routed in different directions.
Fuel System
The fuel tank capacity is approximately:
1.0 L
The LGP10 uses a 1:25 gasoline-to-2-stroke-oil mixture.
Correct fuel preparation is important for engine lubrication and service life. Do not operate the engine using straight gasoline if the supplied engine configuration requires premixed 2-stroke fuel.
Applications
The LEO LGP10 is suitable for:
- Agricultural irrigation
- Garden irrigation
- Water transfer
- Tank filling
- Construction-site water transfer
- General drainage
- Farm water supply
- Small-scale water supply
- Municipal water-transfer applications
- Factory water transfer
- Mine-site water supply/drainage
LEO specifies applications including water supply and drainage for factories, mines and municipal facilities, as well as field irrigation.
Suitable Water
The LGP10 is intended for:
Clean water
or liquids having similar physical and chemical properties.
Specified liquid temperature:
0°C to 40°C.
It is not intended as a sewage pump, slurry pump or solids-handling pump. Abrasive water, mud, sludge or water containing significant suspended solids can cause accelerated wear or blockage.
Main Advantages
- Compact 1-inch gasoline water pump
- No electrical power required during operation
- 1.6 HP gasoline engine
- 42.7 cc displacement
- Single-cylinder 2-stroke engine
- Air-cooled design
- Maximum flow approximately 6 m³/h
- Maximum head approximately 35 m
- Maximum suction approximately 8 m
- Lightweight portable construction
- Low fuel consumption
- Cast-iron impeller and diffuser
- Efficient hydraulic design
- 3-direction adjustable outlet
- Suitable for agricultural irrigation
- Suitable for construction-site water transfer
- Suitable for general clean-water drainage
- 1 L fuel tank
- 1:25 fuel/oil mixture
Important Performance Note
The LGP10 should be selected based on the required flow at the required total head, rather than the 6 m³/h maximum-flow figure alone.
For example, the published LEO curve indicates:
4 m³/h → approximately 26.9 m head
whereas:
6 m³/h → approximately 6 m head.
Therefore, if the application requires high elevation or long pipe runs, the actual delivered flow will be lower than the maximum 100 L/min rating.
LGP10 vs LGP10-A
The model designation is important because LGP10 and LGP10-A are different engine-pump configurations.
| Feature | LGP10 | LGP10-A |
|---|---|---|
| Engine | 2-Stroke | 4-Stroke |
| Displacement | 42.7 cc | 79 cc |
| Power | 1.6 HP | 2 HP |
| Rated Speed | 7,500 rpm | 3,600 rpm |
| Max Flow | 6 m³/h | 15 m³/h |
| Max Head | 35 m | 25 m |
| Max Suction | 8 m | 5 m |
| Fuel Tank | 1 L | 1.8 L |
| Connection | 1" | 1" |
The LGP10-A is therefore not simply a newer version of the LGP10; it is a different 4-stroke configuration with substantially higher maximum flow but lower maximum head.
Maintenance
For dependable operation:
- Use the correct 1:25 2-stroke fuel mixture.
- Keep the suction hose airtight.
- Use an appropriate foot valve/strainer where required.
- Do not run the pump dry.
- Prime the pump before operation.
- Keep the suction strainer clean.
- Inspect the impeller and diffuser periodically.
- Check hose and pipe connections for leakage.
- Keep the air-cooling passages clean.
- Drain or store fuel according to the engine manufacturer's instructions when the pump will not be used for an extended period.
- Operate only with clean water within the specified temperature range.
Technical Product Data
Brand: LEO
Model: LGP10
Category: Gasoline Engine Pump / Petrol Water Pump
Engine Type: Single-Cylinder, 2-Stroke, Air-Cooled
Engine Model: G43
Displacement: 42.7 cc
Maximum Power: 1.6 HP / approx. 1.2 kW
Rated Speed: 7,500 rpm
Maximum Flow: 100 L/min / 6 m³/h
Maximum Head: 35 m
Maximum Suction: 8 m
Inlet: 1" / 25 mm
Outlet: 1" / 25 mm
Fuel Tank: 1.0 L
Fuel Mixture: 1:25 gasoline + 2-stroke oil
Impeller: Anti-rust cast iron
Diffuser: Anti-rust cast iron
Cooling: Air-cooled
Liquid: Clean water
Liquid Temperature: 0°C–40°C
Approx. Dimensions: 336 × 279 × 300 mm
Approx. Net Weight: 8.1 kg.
Inquiry - LEO GASOLINE ENGINE PUMPS - LGP 10