B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LUTIAN DIESEL WATER PUMPS - 100KB-4



The LUTIAN 100KB-4 is a heavy-duty 4-inch diesel water pump designed for high-volume water transfer, agricultural irrigation, plantation operations, construction-site dewatering, drainage, floodwater removal, and general water-supply applications. Powered by a single-cylinder, 4-stroke, air-cooled diesel engine, the 100KB-4 is designed to provide reliable pumping performance in outdoor locations where high water flow and independent engine power are required. Current LUTIAN and Malaysian distributor specifications identify the model with a 418cc LT186FA diesel engine and approximately 10HP output.

The pump features large 4-inch suction and discharge ports, allowing it to move a substantial volume of water with relatively low restriction compared with smaller 2-inch and 3-inch pumps. The current Malaysian product specification lists a maximum flow rate of 1,060 L/min, equivalent to approximately 63.6m³/h, while the current LUTIAN manufacturer specification lists a maximum capacity of 80m³/h. Older LUTIAN catalogue documentation specifies 64m³/h. These figures vary between published versions and test specifications, so actual performance depends on the exact pump configuration and operating conditions.

The 100KB-4 is specified with a maximum pump head of 25m and a maximum suction head of 7m. The 25m head rating indicates the maximum vertical pumping capability under specified test conditions. Actual water flow at a particular installation will depend on total elevation, pipe length, pipe diameter, bends, valves, fittings, suction conditions, and discharge resistance.

Power is supplied by the LUTIAN LT186FA diesel engine. The current manufacturer and Malaysian distributor specifications identify a 418cc single-cylinder, 4-stroke, air-cooled diesel engine with a rated output of approximately 7.5kW / 10HP and rated speed of 3,600 RPM. Some older LUTIAN documentation identifies the engine as LT186F with 406cc displacement and 6.5kW / 9HP output, demonstrating that specifications can differ according to production version or market.

The pump uses a durable aluminium-alloy casing and an iron volute impeller. LUTIAN documentation describes its diesel water pump series as using cast-iron impellers and inner casings with aluminium die-cast pumping casings. The pump also incorporates a mechanical water seal designed to provide water resistance around the pump shaft and support dependable operation.

The 100KB-4 uses a self-priming pump design. After the pump has been correctly primed for initial operation, the design allows subsequent pumping operation without repeatedly adding water under normal conditions. This is particularly useful for agricultural and drainage applications where the pump may be operated for extended periods.

With a large 4-inch pumping passage and approximately 10HP of diesel power, the 100KB-4 is intended for applications requiring substantially higher water volume than conventional 2-inch pumps. It is suitable for farms, plantations, construction sites, drainage projects, ponds, fish farms, irrigation systems, and other outdoor locations where an independent diesel-powered pumping system is preferred.

KEY FEATURES:

• 4-inch heavy-duty diesel water pump
• 4" suction and 4" discharge ports
• Approximately 10HP diesel engine
• 418cc LT186FA diesel engine
• Single-cylinder, 4-stroke, air-cooled engine
• OHV engine configuration
• Maximum flow rate up to 1,060 L/min according to current local specification
• Approximately 63.6m³/h equivalent flow rate
• Manufacturer-listed maximum capacity up to 80m³/h
• Maximum pump head of 25m
• Maximum suction head of 7m
• Self-priming pump design
• Durable aluminium-alloy pump casing
• Iron volute impeller
• Mechanical water seal
• Large-volume water discharge capability
• Low oil-consumption design
• Low-noise diesel engine operation
• Independent operation without mains electricity
• Suitable for continuous outdoor water-transfer work
• Practical for agricultural, construction, drainage, and industrial applications

TECHNICAL SPECIFICATIONS:

Brand: LUTIAN
Model: 100KB-4
Product Type: Diesel Water Pump
Pump Type: Self-Priming Centrifugal Water Pump
Fuel Type: Diesel
Suction Port: 4"
Discharge Port: 4"
Engine Model: LT186FA
Engine Type: Single-Cylinder, 4-Stroke, Air-Cooled Diesel Engine
Engine Displacement: 418cc
Rated Output: 7.5kW / 10HP
Rated Speed: 3,600 RPM
Maximum Flow Rate: 1,060 L/min according to current local specification
Maximum Capacity: Up to 80m³/h according to current LUTIAN specification
Maximum Head: 25m
Maximum Suction Head: 7m
Net Weight: Approximately 63–65kg
Dimensions: Approximately 675 × 500 × 620–635mm depending on specification version

PUMP CONSTRUCTION:

The LUTIAN 100KB-4 is constructed for high-volume water pumping and demanding outdoor use. The aluminium-alloy pump casing helps provide a practical balance between structural strength and overall equipment weight. The iron volute impeller is designed to withstand the mechanical loads associated with high-volume water transfer, while the mechanical water seal helps protect the shaft area against water leakage.

The large 4-inch inlet and outlet are an important feature of the 100KB-4. The larger passages allow greater volumes of water to be transferred and make the model suitable for applications where rapid drainage or high-volume irrigation is required.

DIESEL ENGINE PERFORMANCE:

The LT186FA diesel engine provides approximately 10HP from a 418cc single-cylinder configuration. Its 4-stroke, air-cooled design eliminates the need for a radiator and coolant system, keeping the engine configuration relatively straightforward for outdoor operation and routine maintenance.

The diesel engine allows the pump to operate independently of an electrical power supply. This makes the 100KB-4 suitable for farms, plantations, construction sites, rural properties, drainage areas, and emergency pumping locations where electric power may not be readily accessible.

WATER PUMP PERFORMANCE:

The 100KB-4 is designed primarily for high-volume water movement. The current Malaysian specification lists a maximum flow of 1,060 L/min, while LUTIAN's current manufacturer specification lists a maximum capacity of 80m³/h. Older LUTIAN catalogue information lists 64m³/h. The difference is likely related to different product specifications, engine configurations, testing methods, or market versions.

The pump's maximum head is listed as 25m and its maximum suction head as 7m. These figures should not be interpreted as simultaneous maximum flow and maximum head. As with centrifugal pumps generally, flow decreases as total system head and resistance increase. For a specific installation, actual performance should be determined using the relevant pump performance curve and system conditions.

APPLICATIONS:

The LUTIAN 100KB-4 is suitable for:

• Agricultural irrigation
• Plantation irrigation
• Farm water transfer
• Large garden and landscape watering
• Pond drainage
• Tank filling
• Reservoir water transfer
• Canal water transfer
• Floodwater removal
• Construction-site dewatering
• Excavation and trench drainage
• Fish farms and aquaculture
• Rural water supply
• Industrial water transfer
• Emergency drainage
• General outdoor water pumping

AGRICULTURAL AND IRRIGATION APPLICATIONS:

The 4-inch configuration makes the 100KB-4 suitable for farms and plantations requiring substantial water movement. It can be used to transfer water from ponds, reservoirs, canals, tanks, collection areas, and other suitable water sources to irrigation systems.

For irrigation installations, actual water delivery depends on the complete piping system. Pipe diameter, total pipe length, elevation difference, valves, bends, fittings, suction height, and discharge pressure can all significantly affect the final flow rate. The published maximum capacity should therefore be regarded as a pump rating under specified conditions rather than a guaranteed flow rate at every installation.

CONSTRUCTION AND DEWATERING:

The 100KB-4 is well suited to construction and drainage applications where large quantities of water need to be removed efficiently. The 4-inch discharge connection permits high-volume water transfer from trenches, excavations, work areas, ponds, and other locations where standing water needs to be removed.

Because the pump uses an independent diesel engine, it can operate in locations where electrical infrastructure is unavailable or impractical. This makes it useful for remote construction sites and temporary drainage operations.

SELF-PRIMING DESIGN:

The 100KB-4 uses a self-priming design intended to simplify repeated pumping operations. Proper initial priming is still required before operation, and the suction system must remain properly sealed. Air leakage on the suction side can prevent the pump from establishing or maintaining proper water flow. LUTIAN documentation describes the diesel pump series as self-priming after initial pumping has been established.

MAINTENANCE:

For reliable operation, inspect the engine oil level before starting and perform regular oil changes according to the manufacturer's recommended maintenance schedule. The diesel fuel system should be kept clean, and the air filter should be inspected and serviced regularly.

The suction hose, discharge hose, couplings, clamps, and strainer should be checked for leaks, blockages, cracks, or damage. The suction strainer should be cleaned regularly to prevent debris from restricting water flow. The pump should be properly primed before initial operation and should not be operated without adequate water in the pump chamber.

ACCESSORIES INCLUDED:

The current Malaysian LUTIAN 100KB-4 listing specifies:

• 4-inch PVC coupling × 2
• PVC strainer
• Hose clips × 2

PORTABILITY AND DIMENSIONS:

The current LUTIAN specification lists dimensions of approximately 675 × 500 × 635mm and a net weight of approximately 63kg. A Malaysian distributor lists approximately 675 × 500 × 620mm and 65kg. This remains a portable configuration for a high-capacity 4-inch diesel pump, although lifting and transportation should be carried out using suitable equipment and safe handling procedures.

WHY CHOOSE THE LUTIAN 100KB-4:

The LUTIAN 100KB-4 combines a large 4-inch pumping system with a high-output diesel engine to provide a practical solution for high-volume water transfer. Its self-priming design, air-cooled diesel engine, durable pump construction, large inlet and discharge ports, and independent fuel-powered operation make it suitable for agricultural, plantation, construction, drainage, and industrial applications.

PRODUCT SUMMARY:

The LUTIAN 100KB-4 4" Diesel Water Pump is a heavy-duty, high-flow water pump powered by a 418cc LT186FA diesel engine producing approximately 10HP. It features 4-inch suction and discharge connections, a 25m maximum pump head, 7m maximum suction head, and a current local maximum flow specification of 1,060 L/min. LUTIAN's current manufacturer documentation lists up to 80m³/h maximum capacity, while other LUTIAN catalogue specifications list 64m³/h. The pump is designed for high-volume irrigation, drainage, construction dewatering, floodwater removal, plantation use, and general water-transfer applications.

SPECIFICATION NOTE:

Published specifications for the 100KB-4 vary between current manufacturer data, Malaysian distributors, and older LUTIAN catalogues. The most notable differences concern maximum flow capacity, engine displacement/output, dimensions, and weight. For a Malaysian catalog listing, the current local specification of 418cc, 10HP, 1,060 L/min, 25m head, 7m suction head, and approximately 65kg provides a useful product description, while the manufacturer's current listing states 80m³/h, 418cc, 10HP, 28m pump lift, approximately 63kg, and 675 × 500 × 635mm. The exact specification should be matched to the physical unit and supplier documentation before installation or purchase.



 Inquiry - LUTIAN DIESEL WATER PUMPS - 100KB-4