B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO MULTISTAGE CENTRIFUGAL PUMPS - 2ACM 110



The LEO 2ACm 110 is a horizontal two-stage centrifugal multistage pump designed for clean-water transfer, water supply, pressure boosting, agricultural irrigation, fire-fighting systems, industrial applications and long-distance water transfer. The pump uses a 1.1 kW / 1.5 HP single-phase motor, AISI 304 stainless-steel shaft and a cast-iron hydraulic assembly. LEO specifies a maximum head of approximately 47 m, maximum suction height of 8 m, and maximum liquid temperature of 40°C.

Product Specifications

Specification 2ACm 110
Brand LEO
Model 2ACm 110
Pump Type Multistage Centrifugal Pump
Stage / Impeller 2 Stage
Motor Power 1.1 kW / 1.5 HP
Motor Type Single Phase
Voltage 220–240V
Frequency 50 Hz
Maximum Flow Approx. 250 L/min
Maximum Flow 15 m³/h
Maximum Head Approx. 47 m
Maximum Suction Height 8 m
Suction Connection 1½"
Discharge Connection 1"
Inlet / Outlet 1½" × 1"
Pump Body Cast Iron
Lantern Cast Iron
Shaft AISI 304 Stainless Steel
Impeller AISI 304 Stainless Steel / Cast Iron
Diffuser Cast Iron
Mechanical Seal Carbon / Ceramic
O-Ring NBR
Insulation Class F
Protection Class IPX4
Maximum Liquid Temperature +40°C
Maximum Ambient Temperature +40°C
Maximum Suction 8 m
Pump Orientation Horizontal
Approx. Product Weight 21 kg
Product Dimensions Approx. 430 × 235 × 275 mm

LEO's official technical data gives the 2ACm110 a 1.1 kW rating, maximum head of 47 m, maximum suction height of 8 m, and dimensions of 379 mm hydraulic length × 225 mm height × 200 mm width, while the packaged product specification gives approximately 21 kg and 430 × 235 × 275 mm packaging dimensions.

Hydraulic Performance

The 2ACm110 has a broad performance range depending on the required head.

Flow Flow Conversion Approx. Head
0 L/min 0 m³/h 47 m
20 L/min 1.2 m³/h 46 m
30 L/min 1.8 m³/h 45 m
40 L/min 2.4 m³/h 44 m
50 L/min 3.0 m³/h 43 m
60 L/min 3.6 m³/h 41.5 m
70 L/min 4.2 m³/h 40 m
80 L/min 4.8 m³/h 38 m
90 L/min 5.4 m³/h 35.5 m
100 L/min 6.0 m³/h 33 m
110 L/min 6.6 m³/h 30.5 m
120 L/min 7.2 m³/h 28 m
140 L/min 8.4 m³/h 22 m

LEO's published performance table gives these hydraulic points for the 2ACm110.

The manufacturer's published curve therefore indicates a maximum shut-off head of approximately 47 m and decreasing head as flow increases. The maximum theoretical flow listed for the series is 250 L/min / 15 m³/h, but the published 2ACm110 performance points extend to approximately 140 L/min in the detailed head table.

Two-Stage Multistage Design

The "2" in 2ACm110 identifies the pump as a two-stage configuration. Multiple impeller/diffuser stages allow the pump to generate considerably more pressure than a comparable single-stage pump.

This makes the 2ACm110 suitable for applications where both:

  • Moderate-to-high water flow is required
  • Higher discharge pressure is required

The multistage configuration is particularly useful for pressure boosting, long pipe runs and irrigation systems where hydraulic resistance is significant.

1.1 kW / 1.5 HP Motor

The 2ACm110 uses a 1.1 kW / 1.5 HP single-phase motor. Malaysian listings also identify this model as a 1-phase 1.1 kW / 1.5 HP pump.

The motor incorporates:

  • Built-in thermal protection
  • Class F insulation
  • IPX4 protection
  • Maximum ambient temperature of +40°C

LEO also specifies thermal protection for its single-phase motors in this product family.

Pump Construction

The pump body and lantern are manufactured from cast iron and receive a special cataphoresis anti-rust treatment. This treatment provides additional corrosion protection to the cast-iron components.

The hydraulic construction includes:

  • Cast-iron pump body
  • Cast-iron lantern
  • AISI 304 stainless-steel shaft
  • AISI 304 stainless-steel / cast-iron impeller
  • Cast-iron diffuser
  • Carbon/ceramic mechanical seal
  • NBR O-rings

These materials are intended for clean-water pumping and liquids with physical and chemical properties comparable to water.

AISI 304 Stainless-Steel Shaft

The AISI 304 stainless-steel shaft provides corrosion resistance and durability in normal clean-water applications.

It also provides a robust rotating connection between the motor and multistage hydraulic assembly.

Mechanical Seal

The 2ACm110 uses a carbon/ceramic mechanical seal.

The mechanical seal prevents pumped water from escaping along the rotating shaft into the motor section.

Correct installation, adequate water supply and avoidance of dry running are important for mechanical-seal service life.

1½" × 1" Connections

The 2ACm110 uses:

Suction: 1½"
Discharge: 1"

The asymmetric connection arrangement is designed for the hydraulic configuration of this pump.

For installation, suction piping should be appropriately sized and kept as short and direct as practical to minimize friction losses.

Maximum Suction Height – 8 m

LEO specifies a maximum suction height of 8 m for the 2ACm series.

Actual achievable suction lift depends on:

  • Atmospheric pressure
  • Installation altitude
  • Water temperature
  • Suction-pipe diameter
  • Suction-pipe length
  • Pipe fittings
  • Water level
  • Air leakage
  • Hydraulic losses

A properly sealed suction line is particularly important for installations using suction lift.

Suitable Fluids

The 2ACm110 is designed for clear water or liquids with physical and chemical properties comparable to water.

Suitable applications include:

  • Fresh water
  • Clean tank water
  • Clean well water
  • Irrigation water
  • Treated water
  • General service water

It is not intended for abrasive slurry, heavily contaminated wastewater or chemically aggressive liquids unless material compatibility has been specifically verified.

Applications

The LEO 2ACm110 is suitable for:

  • Domestic water supply
  • Residential water pressure boosting
  • Agricultural irrigation
  • Garden irrigation
  • Fire-fighting systems
  • Industrial water supply
  • Industrial water transfer
  • Long-distance water transfer
  • Air-conditioning systems
  • Water circulation
  • Hot/cold water pressure boosting
  • General clean-water transfer

LEO specifically identifies industrial use, water supply, fire systems, garden irrigation, long-distance water transfer, air-conditioning systems and circulation/overpressure applications for the 2ACm series.

Water Supply & Pressure Boosting

The relatively high head capability makes the 2ACm110 suitable for applications where a standard low-head centrifugal pump may not provide sufficient pressure.

Potential applications include:

  • Multi-storey building water supply
  • House pressure boosting
  • Long-distance pipe runs
  • Shower and tap pressure boosting
  • Storage-tank transfer
  • Water distribution systems
  • Small booster systems

The actual suitability should be determined from the required flow rate and total dynamic head, rather than maximum head alone.

Agricultural Irrigation

The 2ACm110 can be used for small-to-medium agricultural and garden irrigation systems where the required operating point falls within its performance curve.

Applications include:

  • Garden irrigation
  • Small farm irrigation
  • Sprinkler systems
  • Orchard irrigation
  • Tank-to-field transfer
  • Water distribution

For irrigation design, account for elevation difference, pipe friction, fittings, valves and sprinkler operating pressure.

Fire-Fighting Systems

LEO lists fire systems among the applications for this pump family.

However, whether a particular 2ACm110 installation can be used as a code-compliant fire pump depends on the applicable local fire-protection standard, system certification and required duty point. It should not automatically be treated as a certified fire pump solely because the application list includes fire systems.

Long-Distance Water Transfer

The multistage design makes the 2ACm110 useful for water transfer through relatively long pipe runs.

Compared with a basic single-stage low-pressure pump, the 2ACm110 can provide greater head to overcome:

  • Pipe friction
  • Elevation changes
  • Valves
  • Filters
  • Fittings
  • Other system resistance

Correct pipe sizing remains essential because excessive friction can substantially reduce the available flow.

Operating Temperature

LEO specifies:

Maximum liquid temperature: +40°C
Maximum ambient temperature: +40°C.

The pump should be operated within these specified conditions.

Motor Protection

The motor has:

Insulation: Class F
Protection: IPX4
Thermal protection: Integrated for single-phase motor.

IPX4 indicates protection against water splashing from different directions, but the motor should not be exposed to direct high-pressure water jets or submerged.

Installation Recommendations

For reliable operation:

  • Install the pump on a firm, level foundation.
  • Position it as close to the water source as practical.
  • Use correctly sized suction piping.
  • Keep the suction line short and direct.
  • Minimize unnecessary elbows and restrictions.
  • Ensure suction joints are airtight.
  • Install a suitable foot valve/strainer where required.
  • Support pipework independently from the pump.
  • Do not allow pipe weight to load the pump casing.
  • Prime the pump before initial operation.
  • Ensure adequate water supply.
  • Provide proper electrical earthing.
  • Use suitable motor protection.
  • Do not operate the pump dry.
  • Keep operating conditions within the manufacturer's limits.

Maintenance

Recommended maintenance checks include:

  • Inspecting for water leakage
  • Checking mechanical-seal condition
  • Checking suction-line air leakage
  • Cleaning suction strainers
  • Checking impeller condition
  • Inspecting diffusers
  • Checking for abnormal vibration
  • Checking for unusual noise
  • Monitoring motor temperature
  • Checking electrical connections
  • Monitoring pressure and flow
  • Inspecting pipework and valves

Regular maintenance is particularly important where the pump operates continuously or under demanding pressure conditions.

Product Dimensions

LEO's official dimensional data for the 2ACm110 gives approximately:

L: 379 mm
L2: 71 mm
H: 225 mm
H1: 93 mm
W: 200 mm
W1: 162 mm

The official packaging data lists:

Weight: 21 kg
Packaging dimensions: 430 × 235 × 275 mm.

2ACm 110 vs 2ACm 75

Specification 2ACm 75 2ACm 110
Motor Power 0.75 kW 1.1 kW
Approx. HP 1 HP 1.5 HP
Maximum Head 45 m 47 m
Pump Type Multistage Multistage
Stages 2 2
Maximum Suction 8 m 8 m
Main Difference Lower power Higher power

The 2ACm110 provides a higher motor rating and slightly higher maximum head than the 2ACm75.

Key Advantages

Multistage Design: Two hydraulic stages provide higher pressure capability.

1.5 HP Motor: Suitable for domestic, agricultural and light-industrial pressure applications.

High Head: Maximum published head approximately 47 m.

8 m Suction: Suitable for appropriate suction-lift installations.

AISI 304 Shaft: Provides good corrosion resistance.

Cast-Iron Construction: Provides a robust pump structure for general water-supply applications.

Thermal Protection: Helps protect the single-phase motor against overheating.

Multiple Applications: Suitable for water supply, irrigation, pressure boosting, fire systems and industrial water transfer.

Product Summary

The LEO 2ACm 110 is a 1.1 kW / 1.5 HP single-phase horizontal multistage centrifugal pump designed for clean-water transfer and pressure applications. It provides up to approximately 47 m head, with a maximum suction height of 8 m, and uses 1½" suction and 1" discharge connections.

Its two-stage hydraulic design, cast-iron construction, AISI 304 stainless-steel shaft, carbon/ceramic mechanical seal, Class F insulation and IPX4 motor protection make it suitable for domestic water supply, irrigation, pressure boosting, industrial water transfer, fire-system applications and long-distance water transfer.



 Inquiry - LEO MULTISTAGE CENTRIFUGAL PUMPS - 2ACM 110