B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO JET PUMPS - AJM 90S



The LEO AJM90S is a stainless-steel self-priming jet pump designed for clean-water transfer, shallow-well water lifting, domestic water supply, garden irrigation and pressure boosting. It is powered by a 0.9 kW / 1.2 HP, 220 V single-phase motor and provides a useful combination of pressure and flow for residential and light-duty water systems.

Published specifications for the AJM90S give a 5–60 L/min flow range, 44–22 m head range, 9 m maximum suction, and 1" × 1" inlet/outlet connections.

Technical Specifications

Specification LEO AJM90S
Brand LEO
Series AJm-S
Model AJM90S
Pump Type Self-Priming Jet Pump
Motor Power 0.9 kW / 1.2 HP
Voltage 220 V
Phase Single Phase
Frequency 50 Hz
Flow Range 5–60 L/min
Maximum Flow 60 L/min
Equivalent Maximum Flow Approx. 3.6 m³/h
Head Range 44–22 m
Maximum Head Approx. 44 m
Maximum Suction 9 m
Inlet 1"
Outlet 1"
Impeller Stainless Steel
Shaft AISI 304 Stainless Steel
Pump Body Cast Iron with Special Anti-Rust Treatment
Pump Support Cast Iron with Special Anti-Rust Treatment
Motor Winding Copper
Bearing C&U
Thermal Protection Built-In
Insulation Class F
Protection Class IPX4
Maximum Liquid Temperature +40°C*
Maximum Ambient Temperature +40°C
Mechanical Seal Carbon / Ceramic
Duty Continuous

*Some Malaysian listings specify the AJM90S for liquid temperatures up to +60°C, while others specify +40°C. The actual nameplate/regional specification should take precedence.

Pump Performance

The AJM90S is rated for approximately:

  • Flow: 5–60 L/min
  • Maximum flow: 60 L/min
  • Equivalent maximum flow: approximately 3.6 m³/h
  • Maximum head: approximately 44 m
  • Head range: 44–22 m
  • Maximum suction: approximately 9 m
  • Inlet/outlet: 1" × 1"

The 44 m maximum head and 60 L/min maximum flow are not simultaneous operating points. As with other centrifugal pumps, the available head decreases as the flow rate increases. The actual operating point should therefore be selected according to the system's required flow and total dynamic head.

Stainless-Steel AJm-S Construction

The AJM90S belongs to LEO's AJm-S stainless-steel jet-pump range. LEO identifies the AJm-S series for clean-water transfer, well-water lifting, garden sprinkler irrigation and running-water pressure boosting.

The AJM90S incorporates:

  • Stainless-steel impeller
  • AISI 304 stainless-steel shaft
  • Anti-rust-treated pump body and support
  • Self-priming jet hydraulic design
  • Carbon/ceramic mechanical seal

An important catalogue distinction is that the AJM90S is not necessarily a fully stainless-steel pump body. Current Malaysian specifications identify the pump body and support as cast iron under special anti-rust treatment, while the impeller and shaft are stainless steel.

Therefore, for an accurate product listing, use:

Anti-rust-treated cast-iron pump body + stainless-steel impeller + AISI 304 stainless-steel shaft.

Stainless-Steel Impeller

The AJM90S uses a stainless-steel impeller, providing good corrosion resistance and durability in normal clean-water service.

This construction is suitable for:

  • Domestic water supply
  • Well-water pumping
  • Garden irrigation
  • Water tank transfer
  • Pressure boosting
  • General clean-water applications

The pump is not intended for substantial quantities of sand, sludge, fibrous material or abrasive solids.

AISI 304 Stainless-Steel Shaft

The AJM90S incorporates an AISI 304 stainless-steel shaft. This provides good corrosion resistance and mechanical durability in the rotating assembly.

The stainless-steel shaft works together with the stainless-steel impeller to provide a durable hydraulic assembly for standard clean-water applications.

Self-Priming Jet Pump

The AJM90S uses a self-priming jet-pump configuration, allowing the pump to lift water from a source located below the pump.

The published maximum suction is approximately 9 m.

Suitable water sources can include:

  • Shallow wells
  • Underground tanks
  • Ground-level storage tanks
  • Reservoirs
  • Domestic water sources

Actual suction performance depends on the installation. Pipe diameter, suction-pipe length, elevation, number of bends, water temperature and air leakage can all affect the practical suction height.

For reliable operation, the suction pipe should be properly sealed and kept as short and direct as practical.

Motor Specifications

The AJM90S is equipped with a 0.9 kW / 1.2 HP single-phase motor.

Key motor features include:

  • 0.9 kW rated power
  • 1.2 HP
  • 220 V
  • 50 Hz
  • Single phase
  • Copper winding
  • C&U bearing
  • Built-in thermal protector
  • Class F insulation
  • IPX4 protection

The 0.9 kW motor gives the AJM90S higher pressure capability than the AJM75S while retaining a compact 1" × 1" configuration.

Motor Protection

The single-phase motor has a built-in thermal protector to help protect the winding against excessive temperature during abnormal operating conditions.

Electrical protection specifications include:

Insulation Class: F
Protection Class: IPX4
Maximum Ambient Temperature: +40°C

The IPX4 enclosure rating provides protection against water splashing, while Class F insulation provides suitable thermal resistance for the motor winding.

Pump Connections

The AJM90S uses:

Inlet: 1"
Outlet: 1"

The 1" × 1" connection arrangement makes the pump suitable for common domestic water systems, garden irrigation and general water-transfer installations.

For suction applications, an appropriately sized suction pipe should be used to minimize friction losses and help maintain reliable priming.

Mechanical Seal

The AJM-S construction uses a carbon/ceramic mechanical seal. This seals the rotating shaft between the hydraulic and motor sections and helps prevent water leakage.

Pumping Medium

The AJM90S is intended for clean water or other liquids with physical and chemical properties similar to water. LEO specifically identifies the AJm-S series for clean-water transfer, well-water lifting, garden irrigation and pressure boosting.

It should not normally be used for:

  • Sewage
  • Sludge
  • Heavy sediment
  • Abrasive liquids
  • Large suspended solids
  • Fibrous wastewater

For these applications, a dedicated wastewater or solids-handling pump should be selected.

Temperature Rating

There are differences between regional product listings:

  • Some Malaysian specifications: maximum liquid temperature +40°C
  • Other Malaysian AJM90S listings: maximum liquid temperature +60°C
  • Maximum ambient temperature commonly specified: +40°C

For your website catalogue, it is preferable to state the temperature rating corresponding to your actual stock/model specification rather than combining the different regional ratings.

Recommended Applications

Domestic Water Supply

The AJM90S is suitable for residential clean-water systems requiring additional pressure.

Well-Water Lifting

The self-priming configuration and approximately 9 m maximum suction make it suitable for appropriate shallow-well applications.

Garden Irrigation

The maximum flow of approximately 60 L/min makes it suitable for garden sprinklers, hoses and small irrigation systems.

Pressure Boosting

The approximately 44 m maximum head provides useful pressure for domestic and light-duty boosting systems.

Water Tank Transfer

Suitable for transferring clean water between tanks and distribution points.

Small Agricultural Irrigation

Can be used for selected clean-water irrigation applications where the required flow and head fall within the pump curve.

General Water Transfer

The 1.2 HP motor provides a useful balance between pressure and flow for general clean-water transfer.

LEO specifically lists well-water lifting, garden sprinkler irrigation and running-water pressure boosting among the applications for the AJm-S series.

Main Advantages

The LEO AJM90S offers:

  1. 0.9 kW / 1.2 HP motor
  2. Self-priming jet-pump design
  3. 5–60 L/min flow
  4. 44–22 m head range
  5. Approximately 44 m maximum head
  6. Approximately 9 m maximum suction
  7. Stainless-steel impeller
  8. AISI 304 stainless-steel shaft
  9. Anti-rust-treated cast-iron pump body and support
  10. Copper motor winding
  11. C&U bearing
  12. Built-in thermal protection
  13. Class F insulation
  14. IPX4 protection
  15. 1" × 1" inlet/outlet
  16. Carbon/ceramic mechanical seal
  17. Compact construction
  18. Suitable for domestic, irrigation, well-water and pressure-boosting applications.

AJM90S vs AJM75S

Feature AJM75S AJM90S
Motor 0.75 kW / 1 HP 0.9 kW / 1.2 HP
Voltage 220 V 220 V
Flow 5–55 L/min 5–60 L/min
Head 40–20 m 44–22 m
Max. Suction 9 m 9 m
Inlet/Outlet 1" × 1" 1" × 1"
Impeller Stainless Steel Stainless Steel
Shaft AISI 304 AISI 304
Pump Body Anti-rust-treated Anti-rust-treated

The AJM90S provides a modest increase in both maximum flow and head over the AJM75S, making it appropriate when the application requires somewhat greater pressure or water delivery. The published AJM90S specifications are 5–60 L/min and 44–22 m.

AJM-S Series Comparison

Model Motor Flow Range Head Range Max. Suction Connection
AJM45S 0.45 kW / 0.6 HP 5–40 L/min 35–16 m 9 m 1" × 1"
AJM75S 0.75 kW / 1 HP 5–55 L/min 40–20 m 9 m 1" × 1"
AJM90S 0.9 kW / 1.2 HP 5–60 L/min 44–22 m 9 m 1" × 1"

The AJM90S is the higher-capacity option in this group, providing the highest motor power, flow and head among these three models.

Dimensions & Weight

One Malaysian specification lists the AJM90S at approximately:

  • Width: 42 cm
  • Depth: 28 cm
  • Height: 25 cm
  • Weight: approximately 10 kg
  • 1" × 1" connections

Another Malaysian supplier lists approximately 45.5 × 21.5 × 24.5 cm and 16.45 kg, demonstrating that supplier measurements and packaged weights can vary.

For a website catalogue, the manufacturer's actual product/packaging specification should take precedence.

Product Description

LEO AJM90S Jet Pump 0.9kW / 1.2HP 220V is a stainless-steel self-priming jet pump designed for clean-water transfer, shallow-well water lifting, domestic water supply, garden irrigation and pressure boosting. Powered by a 0.9 kW / 1.2 HP single-phase motor, the AJM90S delivers approximately 5–60 L/min flow with a 44–22 m head range, providing a practical balance of pressure and water flow for residential and light-duty applications.

The pump features a stainless-steel impeller and AISI 304 stainless-steel shaft, together with an anti-rust-treated cast-iron pump body and support. The motor uses copper winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection for reliable operation under suitable conditions.

With 1" × 1" inlet and outlet connections and approximately 9 m maximum suction capability, the LEO AJM90S is suitable for shallow-well water lifting, garden irrigation, domestic water supply, water tank transfer, pressure boosting and general clean-water pumping applications.

SEO Product Title

LEO AJM90S Jet Pump 0.9kW 1.2HP 220V Stainless Steel Self-Priming Water Pump

Short Product Description

LEO AJM90S is a 0.9kW / 1.2HP 220V stainless-steel self-priming jet pump designed for clean-water transfer, well-water lifting, garden irrigation and pressure boosting. It provides approximately 5–60 L/min flow with a 44–22 m head range, featuring a stainless-steel impeller, AISI 304 shaft, anti-rust-treated cast-iron pump body, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. With 1" × 1" connections and approximately 9 m maximum suction, it is suitable for domestic, irrigation and general clean-water pumping applications.



 Inquiry - LEO JET PUMPS - AJM 90S