The LEO AJM75S is a stainless-steel self-priming jet pump designed for clean-water transfer, shallow-well water lifting, domestic water supply, garden irrigation and pressure boosting. It is equipped with a 0.75 kW / 1 HP, 220 V single-phase motor and is designed to provide a good balance between water flow and pressure for residential and light-duty applications.
Published Malaysian specifications list the AJM75S at approximately 5–55 L/min flow, 40–20 m head, 9 m maximum suction and 1" × 1" inlet/outlet connections.
Technical Specifications
| Specification | LEO AJM75S |
|---|---|
| Brand | LEO |
| Series | AJm-S |
| Model | AJM75S |
| Pump Type | Self-Priming Jet Pump |
| Motor Power | 0.75 kW / 1 HP |
| Voltage | 220 V |
| Phase | Single Phase |
| Frequency | 50 Hz |
| Rated Speed | Approx. 2,900 RPM |
| Flow Range | 5–55 L/min |
| Maximum Flow | 55 L/min |
| Equivalent Maximum Flow | Approx. 3.3 m³/h |
| Head Range | 40–20 m |
| Maximum Head | Approx. 40 m |
| Maximum Suction | 9 m |
| Inlet | 1" |
| Outlet | 1" |
| Impeller | Stainless Steel |
| Pump Body | Stainless Steel / AJm-S configuration |
| Shaft | AISI 304 Stainless Steel |
| Motor Winding | Copper |
| Bearing | C&U |
| Thermal Protection | Built-In |
| Insulation Class | F |
| Protection Class | IPX4 |
| Maximum Liquid Temperature | +40°C to +60°C, depending on regional specification |
| Maximum Ambient Temperature | +40°C |
| Mechanical Seal | Carbon / Ceramic |
| Duty | Continuous |
The core Malaysian specifications are consistently listed as 0.75 kW / 1 HP, 220 V, 5–55 L/min, 40–20 m head, 9 m suction and 1" × 1" connections.
Pump Performance
The AJM75S provides a maximum published flow of approximately 55 L/min, equivalent to around 3.3 m³/h.
Its published head range is approximately 40–20 m. This means the pump can develop around 40 m maximum head at the low-flow end of its curve, while the available head decreases as flow increases.
The main performance figures are:
- Flow: 5–55 L/min
- Maximum flow: 55 L/min
- Maximum head: approximately 40 m
- Operating head range: 40–20 m
- Maximum suction: approximately 9 m
- Inlet/outlet: 1" × 1"
For pump selection, the actual required flow rate and total dynamic head (TDH) should be matched against the manufacturer's pump curve rather than selecting based solely on maximum flow or maximum head.
Stainless-Steel AJm-S Construction
The “S” suffix identifies the stainless-steel version of the AJm range.
The AJM75S is commonly specified with:
- Stainless-steel pump body
- Stainless-steel impeller
- AISI 304 stainless-steel shaft
- Anti-rust treatment on wetted components
- Carbon/ceramic mechanical seal
A Malaysian supplier specifically identifies the AJM75S as having a stainless-steel pump body, stainless-steel impeller and AISI 304 fabricated shaft.
This construction provides good corrosion resistance for normal clean-water pumping applications.
Stainless-Steel Impeller
The AJM75S uses a stainless-steel impeller, providing durability and corrosion resistance in clean-water service.
The impeller is suitable for applications such as:
- Domestic water supply
- Well-water pumping
- Garden irrigation
- Water tank transfer
- Pressure boosting
- General clean-water transfer
It is not intended for pumping substantial quantities of sand, sludge, fibrous material or abrasive solids.
AISI 304 Stainless-Steel Shaft
The pump incorporates an AISI 304 stainless-steel shaft. This material provides good corrosion resistance and mechanical durability in the rotating assembly.
The combination of stainless-steel shaft and impeller makes the AJM75S well suited to standard clean-water applications.
Self-Priming Jet Pump
The AJM75S uses a self-priming jet-pump system, allowing it to lift water from a source below the pump.
The published maximum suction is approximately 9 m.
Typical water sources include:
- Shallow wells
- Underground tanks
- Ground-level water tanks
- Reservoirs
- Domestic water sources
Actual suction performance depends on installation conditions. Long suction pipes, excessive bends, undersized piping, air leakage and elevation can reduce the practical suction capability.
For optimum performance, the suction line should be as short and direct as practical and all connections should be properly sealed.
Motor Specifications
The AJM75S is equipped with a 0.75 kW / 1 HP single-phase motor.
Key motor characteristics include:
- Motor power: 0.75 kW
- Motor rating: 1 HP
- Voltage: 220 V
- Frequency: 50 Hz
- Single phase
- Copper winding
- C&U bearing
- Built-in thermal protector
- Class F insulation
- IPX4 protection
A Malaysian technical listing also gives approximately 2,900 RPM, 5 A current and a 16 μF / 450 V capacitor for one AJM75S configuration.
Motor Protection
The AJM75S single-phase motor incorporates a built-in thermal protector to help prevent overheating under abnormal operating conditions.
The motor is specified with:
Insulation Class: F
Protection Class: IPX4
Maximum Ambient Temperature: +40°C
IPX4 provides protection against water splashing, while Class F insulation provides suitable thermal resistance for the motor winding.
Pump Connections
The AJM75S uses:
Inlet: 1"
Outlet: 1"
This 1" × 1" connection makes the pump suitable for many standard domestic water-supply and irrigation installations.
For suction applications, an appropriately sized suction pipe should be used to minimize friction losses and maintain reliable priming.
Mechanical Seal
The AJM-S series uses a carbon/ceramic mechanical seal. This provides sealing around the rotating shaft and helps prevent water from entering the motor section.
Pumping Medium
The AJM75S is designed for clean water or liquids with physical and chemical properties similar to water. LEO's AJM-S application guidance covers well-water lifting, garden irrigation, pressure boosting and related clean-water applications.
It should not normally be used for:
- Sewage
- Sludge
- Heavy sediment
- Abrasive liquids
- Large suspended solids
- Fibrous wastewater
For these applications, a dedicated wastewater or solids-handling pump is more appropriate.
Temperature Rating
Published specifications vary slightly by market and product configuration.
One Malaysian supplier specifies a maximum liquid temperature of +40°C, while another AJM75S listing gives up to +60°C.
For your product catalogue, the temperature rating should be matched to the exact regional model and nameplate supplied.
Recommended Applications
Domestic Water Supply
The AJM75S is suitable for supplying clean water to residential systems where moderate-to-high pressure is required.
Well-Water Lifting
Its self-priming design and approximately 9 m maximum suction make it suitable for shallow-well applications within the pump's operating limitations.
Garden Irrigation
The 55 L/min maximum flow makes it suitable for garden sprinklers, hoses and small irrigation systems.
Pressure Boosting
The approximately 40 m maximum head provides useful pressure for selected domestic and light-duty boosting applications.
Water Tank Transfer
The pump can be used to transfer clean water between storage tanks and distribution points.
Agricultural Irrigation
The AJM75S can be used for small-scale clean-water irrigation where the required duty point is within the pump curve.
General Water Transfer
Its 1 HP motor and compact configuration make it suitable for general clean-water transfer applications.
Main Advantages
The LEO AJM75S offers:
- 0.75 kW / 1 HP motor
- Self-priming jet-pump design
- 5–55 L/min flow
- 40–20 m head range
- Approximately 40 m maximum head
- Approximately 9 m maximum suction
- Stainless-steel pump construction
- Stainless-steel impeller
- AISI 304 stainless-steel shaft
- Copper motor winding
- C&U bearing
- Built-in thermal protection
- Class F insulation
- IPX4 protection
- 1" × 1" inlet/outlet
- Carbon/ceramic mechanical seal
- Compact construction
- Suitable for domestic, irrigation, well-water and pressure-boosting applications.
AJM75S vs AJM75
The AJM75S and AJM75 have similar hydraulic performance, but the AJM75S is the stainless-steel version.
| Feature | AJM75 | AJM75S |
|---|---|---|
| Motor | 0.75 kW / 1 HP | 0.75 kW / 1 HP |
| Voltage | 220 V | 220 V |
| Flow | 5–55 L/min | 5–55 L/min |
| Head | 40–20 m | 40–20 m |
| Max. Suction | 9 m | 9 m |
| Inlet/Outlet | 1" × 1" | 1" × 1" |
| Impeller | Stainless Steel | Stainless Steel |
| Pump Construction | Standard | Stainless-Steel AJm-S |
The main purchasing distinction is therefore the pump-body construction, rather than motor power or basic hydraulic capacity.
AJM-S Series Comparison
| Model | Motor | Flow Range | Head Range | Max. Suction | Connection |
|---|---|---|---|---|---|
| AJM45S | 0.45 kW / 0.6 HP | 5–40 L/min | 35–16 m | 9 m | 1" × 1" |
| AJM75S | 0.75 kW / 1 HP | 5–55 L/min | 40–20 m | 9 m | 1" × 1" |
| AJM90S | 0.90 kW / 1.2 HP | 5–60 L/min* | 44–22 m* | 9 m | 1" × 1" |
*Specifications can vary by regional model/version; verify the actual nameplate and manufacturer's curve for the exact unit.
The AJM75S sits between the smaller AJM45S and higher-powered AJM90S, providing a practical 1 HP solution for domestic water pressure and irrigation.
Dimensions & Weight
Published Malaysian supplier information gives approximately:
- Dimensions: 420 × 280 × 250 mm
- Weight: approximately 10 kg
Another Malaysian supplier lists approximately 44 × 26 × 28 cm and 12 kg, demonstrating that packaged/product measurements vary between suppliers.
For website catalogue purposes, use the dimensions and weight supplied on the actual manufacturer's packaging where possible.
Product Description
LEO AJM75S Jet Pump 0.75kW / 1HP 220V is a stainless-steel self-priming water pump designed for clean-water transfer, shallow-well water lifting, domestic water supply, garden irrigation and pressure boosting. Powered by a 0.75 kW / 1 HP single-phase motor, the AJM75S delivers approximately 5–55 L/min flow with a 40–20 m head range, providing a practical combination of water pressure and flow for residential and light-duty applications.
The pump features a stainless-steel pump body, stainless-steel impeller and AISI 304 stainless-steel shaft, together with copper motor winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection. Its self-priming jet design provides approximately 9 m maximum suction capability, subject to actual installation conditions.
With 1" × 1" inlet and outlet connections, the LEO AJM75S is suitable for shallow-well water lifting, garden irrigation, domestic water supply, water tank transfer, pressure boosting and general clean-water pumping applications.
SEO Product Title
LEO AJM75S Jet Pump 0.75kW 1HP 220V Stainless Steel Self-Priming Water Pump
Short Product Description
LEO AJM75S is a 0.75kW / 1HP 220V stainless-steel self-priming jet pump designed for clean-water transfer, well-water lifting, garden irrigation and pressure boosting. It delivers approximately 5–55 L/min flow with a 40–20 m head range, featuring a stainless-steel pump body, stainless-steel impeller, AISI 304 shaft, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. With 1" × 1" connections and approximately 9 m maximum suction, it is suitable for domestic, irrigation and general clean-water pumping applications.
Inquiry - LEO JET PUMPS - AJM 75S