B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - AJDM 55/4H



The LEO AJDm55/4H is a 0.55 kW / 0.75 HP deep-well jet pump designed for lifting clean water from wells and for applications such as garden irrigation, domestic water supply, pressure boosting and general clean-water transfer. It uses a deep-well ejector arrangement and is intended for installations where a conventional shallow-well jet pump is unsuitable. LEO's official product information specifically lists the AJDm55/4H within its Jet Pump for Deep Wells range.

Technical Specifications

Specification LEO AJDm55/4H
Brand LEO
Series AJDm
Model AJDm55/4H
Pump Type Deep-Well Jet Pump
Pump Design Self-Priming Jet Pump
Motor Power 0.55 kW / 0.75 HP
Motor Single Phase
Rated Frequency 50 Hz
Flow Range Up to approximately *15 m³/h **
Published Hydraulic Data 0–15 m³/h
Maximum Head Approx. 39 m
Maximum Suction Up to 40 m according to LEO catalogue data
Main Pump Connection 1-1/4"
Jet/Ejector Connections 1" × 1" × 1"
Impeller Stainless Steel
Pump Body Cast Iron, Special Anti-Rust Treatment
Pump Support Anti-Rust-Treated Construction
Shaft AISI 304 Stainless Steel
Nozzle PPO
Venturi Tube PPO
Ejector HT200
Mechanical Seal Carbon / Ceramic
O-Ring NBR
Motor Winding Copper
Bearing C&U
Thermal Protection Built-In
Insulation Class F
Protection Class IPX4
Max. Ambient Temperature +40°C
Max. Liquid Temperature +40°C
Approx. Product Weight 16.65 kg gross/package weight

*The LEO catalogue's technical table uses flow/head operating points differently from some regional retail listings. The official table for AJDm55/4H lists HS 15 m and head values from 39 m at zero flow down to 13 m at 24 m³/h-equivalent table increments, while Malaysian retail listings commonly present the model as approximately 2–24 L/min. Therefore, for a commercial listing, the manufacturer's pump curve/nameplate should be treated as the controlling specification.

Deep-Well Pumping Design

The AJDm55/4H is specifically engineered as a deep-well jet pump. Unlike a normal surface jet pump, its hydraulic system incorporates an ejector/venturi assembly that allows the pump to lift water from a deeper source.

LEO states that the AJDm series is suitable for:

  • Lifting water from wells
  • Garden sprinkler irrigation
  • Running-water pressure boosting
  • Supporting equipment
  • General clean-water transfer.

The model's deep-well configuration makes it suitable for applications where the water level is beyond the practical suction capability of an ordinary surface pump.

Maximum Suction / Lifting Depth

LEO's catalogue information for the AJDm range specifies maximum suction up to approximately 40 m, while some regional listings for the AJDm55/4H quote around 30 m depending on the particular specification or installation configuration.

For a website product listing, this distinction is important. A practical installation should not be designed simply around the maximum advertised number.

Actual lifting performance depends on:

  • Static water level
  • Dynamic water level while pumping
  • Ejector depth
  • Ejector configuration
  • Suction/return pipe diameter
  • Pipe length
  • Pipe friction losses
  • Number of bends
  • Foot-valve condition
  • Air leakage
  • Required discharge pressure

The 40 m figure should therefore be treated as a maximum catalogue capability, not a guaranteed flow condition at 40 m depth.

Pump Performance

The official LEO technical table for the AJDm55/4H provides the following head values at increasing flow:

Flow Point Approx. Head
0 39 m
2 35 m
4 33 m
6 29 m
8 27 m
10 25 m
12 23 m
14 21 m
16 19 m
18 17 m
20 15 m
22 14 m
24 13 m

These values illustrate the normal centrifugal-pump relationship: available head decreases as flow increases.

For example, the pump can develop approximately 39 m head at zero flow, but the available head falls to approximately 25 m at the 10 L/min point and approximately 13 m at the 24 L/min point according to the published table.

For actual system selection, the operating point should be determined from the pump curve together with the system's total dynamic head.

0.55 kW / 0.75 HP Motor

The AJDm55/4H is equipped with a compact 0.55 kW / 0.75 HP motor. LEO's technical data confirms the 0.55 kW / 0.75 HP rating.

The motor is designed for clean-water pumping applications and incorporates:

  • Copper winding
  • C&U bearing
  • Built-in thermal protector
  • Class F insulation
  • IPX4 protection
  • Maximum ambient temperature of +40°C.

This makes the AJDm55/4H a suitable lower-power option within the AJDm deep-well range.

Stainless-Steel Impeller

The AJDm55/4H uses a stainless-steel impeller. This provides improved corrosion resistance compared with a conventional untreated cast-iron impeller and is appropriate for clean-water and groundwater applications.

Suitable applications include:

  • Well water
  • Fresh water
  • Garden irrigation
  • Domestic water supply
  • Water tank transfer
  • Small-scale agricultural irrigation

The pump should not be used for heavily abrasive liquids, sewage, sludge or liquids containing significant suspended solids.

AISI 304 Stainless-Steel Shaft

The shaft is manufactured from AISI 304 stainless steel.

This provides good corrosion resistance and mechanical durability for the rotating assembly.

The combination of:

Stainless-steel impeller + AISI 304 shaft

provides a durable hydraulic assembly for normal clean-water service.

Pump Body Construction

The AJDm55/4H is not a completely stainless-steel pump.

LEO specifies:

  • Pump body: HT200 cast iron
  • Special anti-rust treatment
  • Stainless-steel impeller
  • AISI 304 shaft
  • Anti-rust-treated support components.

This construction gives the pump good mechanical strength while incorporating stainless steel in the critical rotating hydraulic components.

For accurate product marketing, it is preferable to describe the unit as:

“LEO deep-well jet pump with stainless-steel impeller and AISI 304 shaft”

rather than “full stainless-steel deep-well pump.”

Ejector & Venturi Construction

The AJDm55/4H incorporates a dedicated deep-well ejector assembly.

The LEO material specification identifies:

  • Nozzle: PPO
  • Venturi tube: PPO
  • Ejector: HT200
  • Mechanical seal: Carbon/Ceramic
  • O-ring: NBR.

The nozzle and venturi arrangement is central to the deep-well jet-pump operating principle. A portion of the pumped water is circulated through the ejector to generate the suction effect needed to lift water from the well.

Connection Sizes

The LEO dimensional data specifies the following connections for the AJDm55/4H:

Connection Size
Main Pump Connection 4" pump/ejector specification
DN1 1-1/4"
DN2 1"
DN3 1"
DN4 1"

The physical dimensional table lists DNp = 4", DN1 = 1-1/4", and DN2/DN3/DN4 = 1".

Some Malaysian retail listings simplify the connection specification to 1-1/4" × 1", so the exact pipe arrangement should be confirmed against the installation diagram supplied with the unit.

Mechanical Seal

The AJDm55/4H uses a Carbon/Ceramic mechanical seal.

The mechanical seal prevents water from escaping along the rotating shaft between the hydraulic section and motor section.

This is particularly important for deep-well applications because the pump may operate for extended periods during domestic or irrigation water supply.

Motor Protection

The single-phase motor incorporates a built-in thermal protector. This helps protect the winding from overheating under abnormal operating conditions.

External electrical protection should nevertheless be installed in accordance with the applicable electrical installation requirements.

Insulation & Protection

The AJDm55/4H is specified with:

Insulation Class: F
Protection Class: IPX4
Maximum Ambient Temperature: +40°C.

IPX4 provides protection against water splashing from different directions. The pump should still be installed in an appropriately protected location and should not be submerged.

Maximum Liquid Temperature

LEO specifies a maximum liquid temperature of +40°C for the AJDm55/4H. The maximum ambient temperature is also +40°C.

This makes the pump appropriate for:

  • Groundwater
  • Domestic cold water
  • Garden irrigation
  • Agricultural irrigation
  • Water-storage systems

It is not intended as a hot-water circulation pump.

Pumping Medium

The AJDm55/4H is designed for clean water or liquids with physical and chemical properties similar to water.

Recommended fluids include:

  • Clean groundwater
  • Fresh water
  • Rainwater after appropriate filtration
  • Irrigation water
  • Domestic water
  • Storage-tank water

It is not recommended for:

  • Sewage
  • Mud
  • Sludge
  • Heavy sand
  • Abrasive liquids
  • Fibrous liquids
  • Large suspended solids

If a well contains substantial sand, the well should be properly developed and appropriate filtration should be considered.

Recommended Applications

Deep-Well Water Supply

The primary application is lifting clean groundwater from wells using the appropriate ejector configuration.

Garden Irrigation

The AJDm55/4H can supply garden sprinklers and irrigation lines where the required flow and pressure fall within the pump curve.

Domestic Water Supply

It can be used to supply clean water from a suitable well to a house or other domestic installation.

Water Tank Filling

The pump can transfer groundwater to storage tanks or elevated tanks.

Pressure Boosting

The pump can increase water pressure in suitable clean-water systems.

Small Agricultural Applications

The 0.75 HP rating makes it suitable for smaller-scale irrigation systems where high flow is not required.

LEO specifically identifies well-water lifting, garden sprinkler irrigation and running-water pressure boosting as applications for the AJDm series.

Key Advantages

The LEO AJDm55/4H offers:

  1. 0.55 kW / 0.75 HP motor
  2. Deep-well jet-pump design
  3. Self-priming operation
  4. Deep-well ejector system
  5. Stainless-steel impeller
  6. AISI 304 stainless-steel shaft
  7. Anti-rust-treated cast-iron pump body
  8. PPO nozzle and venturi components
  9. HT200 ejector
  10. Carbon/ceramic mechanical seal
  11. Copper motor winding
  12. C&U bearing
  13. Built-in thermal protection
  14. Class F insulation
  15. IPX4 protection
  16. Maximum liquid temperature +40°C
  17. Maximum ambient temperature +40°C
  18. Suitable for well-water lifting
  19. Suitable for garden irrigation
  20. Suitable for domestic water supply
  21. Suitable for pressure boosting.

AJDM55/4H vs AJDM75/4H vs AJDM110/4H

Feature AJDM55/4H AJDM75/4H AJDM110/4H
Motor Power 0.55 kW / 0.75 HP 0.75 kW / 1 HP 1.1 kW / 1.5 HP
Pump Type Deep-Well Jet Deep-Well Jet Deep-Well Jet
Impeller Stainless Steel Stainless Steel Stainless Steel
Shaft AISI 304 AISI 304 AISI 304
Main Application Deep well / garden Deep well / garden Deep well / garden
Relative Capacity Entry Medium Higher
Relative Pressure Lower Medium Higher
Best For Smaller installations Medium installations Higher-demand systems

The AJDM55/4H is the lower-power option, making it appropriate when the required flow and pressure are moderate. The 0.75 HP motor can provide a more economical solution for smaller domestic or irrigation systems, provided the hydraulic requirements are within its pump curve.

Dimensions & Weight

LEO's published dimensional information gives approximately:

  • Overall length (L): 370 mm
  • L1: 77 mm
  • Mounting dimension: 190 mm
  • Mounting dimension: 150 mm
  • Overall height (H): 212 mm
  • H1: 100 mm
  • a1: 160 mm
  • a2: 53 mm
  • S: 10 mm.

The catalogue package information lists:

Gross weight: approximately 16.65 kg
Package size: approximately 500 × 215 × 240 mm.

Because supplier listings can quote different packaged dimensions and weights, the manufacturer's actual packing specification should be used for shipping calculations.

Installation Considerations

Correct installation is particularly important with deep-well jet pumps.

Before installation:

  • Check the actual static and dynamic water level.
  • Confirm the appropriate ejector arrangement.
  • Install the ejector at the recommended depth.
  • Use suitable pipe sizes.
  • Ensure suction/return connections are completely airtight.
  • Install a suitable foot valve where required.
  • Minimize excessive pipe bends.
  • Ensure the well can supply the required water volume.
  • Prime the pump correctly.
  • Never operate the pump dry.
  • Provide suitable electrical protection and earthing.

The physical depth of the well is not the same as the pumping depth. The critical measurement is the distance from the pump/ejector system to the actual water level during operation.

Product Description

LEO AJDM55/4H Deep-Well Jet Pump 0.55kW / 0.75HP is a compact self-priming deep-well water pump designed for lifting clean water from wells and supplying water for garden irrigation, domestic water supply, water tank filling and pressure boosting. The deep-well ejector arrangement allows the pump to operate with significantly greater lifting capability than a conventional shallow-well surface jet pump.

The pump features a stainless-steel impeller, AISI 304 stainless-steel shaft and anti-rust-treated cast-iron pump body, together with PPO nozzle and venturi components and an HT200 ejector. The 0.55 kW / 0.75 HP single-phase motor incorporates copper winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection.

LEO's published hydraulic data shows approximately 39 m maximum head at zero flow, reducing progressively as flow increases. The model is suitable for clean-water applications where moderate flow and pressure are required, making it a practical choice for deep-well water lifting, household water supply and garden irrigation systems.

SEO Product Title

LEO AJDM55/4H Deep Well Jet Pump 0.55kW 0.75HP Self-Priming Garden Water Pump

Short Product Description

LEO AJDM55/4H is a 0.55kW / 0.75HP deep-well self-priming jet pump designed for lifting clean water from wells, garden irrigation, domestic water supply and pressure boosting. It features a stainless-steel impeller, AISI 304 stainless-steel shaft, anti-rust-treated cast-iron pump body, PPO venturi/nozzle system, HT200 ejector, carbon/ceramic mechanical seal and copper-wound motor. With approximately 39 m maximum head and deep-well suction capability dependent on the ejector and installation configuration, the AJDM55/4H is suitable for smaller deep-well and garden water-pumping systems.



 Inquiry - LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - AJDM 55/4H