B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - EKJ-802S



The LEO EKJ-802S is a 0.8 kW self-priming stainless-steel garden jet pump designed for clean-water transfer, domestic water pressurisation, shallow-well water lifting, garden irrigation and general water-supply applications. It operates on 220–240 V, 50 Hz single-phase power and provides approximately 3.5–3.7 m³/h maximum flow, with a maximum head of around 38–40 m depending on the specification/version.

The EKJ-802S is the S-version of the EKJ garden jet-pump range and is identified by Malaysian suppliers as the successor to the older LKJ-800S model.

Technical Specifications

Specification LEO EKJ-802S
Brand LEO
Series EKJ
Model EKJ-802S
Previous Model LKJ-800S
Pump Type Self-Priming Garden Jet Pump
Construction Stainless-Steel Jet Pump
Motor Power 0.8 kW / approx. 1.0–1.1 HP
Voltage 220–240 V
Frequency 50 Hz
Phase Single Phase
Maximum Flow Approx. 60–62 L/min
Maximum Capacity Approx. 3.5–3.7 m³/h
Maximum Head 38–40 m
Maximum Suction 7–8 m
Inlet 1"
Outlet 1"
Impeller Closed Impeller
Impeller Material Technopolymer / PPO
Shaft AISI 304 Stainless Steel
Pump Body AISI 304 Stainless Steel
Motor Winding Copper
Insulation Class F
Protection Class IPX4
Thermal Protection Built-In
Maximum Liquid Temperature +35°C
Maximum Ambient Temperature +40°C
Installation Surface Mounted
Suitable Liquid Clean Water / Non-Aggressive Liquids

LEO's technical documentation lists the EKJ-802S at 800 W, 38 m maximum head, 3.5 m³/h maximum flow and 7 m maximum suction, while other current listings give approximately 40 m head, 3.7 m³/h / 62 L/min and 8 m suction. These differences should be treated as regional/model-documentation variations.

Self-Priming Garden Jet Pump

The EKJ-802S is a surface-mounted self-priming centrifugal jet pump. It is designed to draw clean water from a source below the pump and is particularly suitable for domestic and garden water systems. LEO's EKJ series is intended for garden use and domestic water pressurisation.

The self-priming design makes the pump suitable for applications such as:

  • Shallow wells
  • Groundwater sources
  • Storage tanks
  • Rainwater tanks
  • Garden irrigation
  • Domestic water supply
  • Water pressure boosting
  • Small irrigation systems
  • Water transfer

The pump still requires correct initial priming and an airtight suction system.

0.8 kW Motor

The EKJ-802S is equipped with an 800 W / 0.8 kW single-phase motor. Malaysian listings commonly market this as approximately 1.1 HP, while some specifications round it to 1 HP.

The motor operates from a 220–240 V, 50 Hz supply.

This power rating provides useful pressure for:

  • Domestic water systems
  • Garden sprinklers
  • Small irrigation networks
  • Water tanks
  • Shallow wells
  • Pressure boosting

The motor uses copper winding and incorporates a thermal protector.

Maximum Flow – Approximately 60–62 L/min

The EKJ-802S is commonly specified with a maximum flow of approximately 60–62 L/min, equivalent to around 3.5–3.7 m³/h.

Maximum flow is the pump's high-flow operating limit and does not occur simultaneously with maximum head.

Actual flow will depend on the complete hydraulic system, including:

  • Total dynamic head
  • Pipe length
  • Pipe diameter
  • Vertical elevation
  • Pipe fittings
  • Valves
  • Filters
  • Required outlet pressure
  • Suction conditions

For professional pump selection, the manufacturer's pump curve should be used to determine the actual operating point.

Maximum Head – 38–40 m

The EKJ-802S is documented with a maximum head in the 38–40 m range. LEO's technical documentation specifies 38 m, while several current Malaysian and regional listings specify 40 m.

This means the pump can generate substantial pressure for its compact 0.8 kW motor.

A 40 m water head is approximately equivalent to 4 bar of static water pressure, before pipe and system losses.

The actual pressure available at a given flow will be lower than the theoretical maximum head.

Maximum Suction – 7–8 m

The EKJ-802S has a published maximum suction depth of approximately 7–8 m. LEO's technical manual lists 7 m, while other specifications list 8 m.

This makes the pump suitable for shallow-well applications, but it should not be confused with a deep-well ejector pump capable of lifting water from several tens of metres.

Suction performance can be affected by:

  • Water level
  • Atmospheric pressure
  • Water temperature
  • Suction pipe diameter
  • Suction pipe length
  • Foot valve
  • Air leakage
  • Pipe friction
  • Number of bends

For optimum performance, position the pump as close as practical to the water source.

Stainless-Steel Pump Body

One of the key features of the EKJ-802S is its stainless-steel construction.

The pump body is specified as stainless steel/AISI 304 in product documentation and regional listings.

This construction provides:

  • Good corrosion resistance
  • Durable pump housing
  • Clean appearance
  • Improved resistance to environmental moisture
  • Suitability for domestic and garden water applications

The stainless-steel housing differentiates the S version from some other EKJ configurations.

AISI 304 Stainless-Steel Shaft

The pump shaft is made from AISI 304 stainless steel.

AISI 304 provides good corrosion resistance and mechanical durability in normal clean-water service.

The stainless-steel shaft is particularly useful for:

  • Groundwater pumping
  • Domestic water supply
  • Garden irrigation
  • Tank water transfer
  • Outdoor installations

Technopolymer / PPO Impeller

The EKJ-802S uses a technopolymer/PPO impeller according to LEO's technical documentation and regional product information.

The impeller is designed for clean-water pumping and contributes to the pump's lightweight construction.

It should not be used for liquids containing significant quantities of:

  • Sand
  • Gravel
  • Abrasive particles
  • Sludge
  • Fibres
  • Large suspended solids

If groundwater contains sand, appropriate filtration should be installed before the pump.

Closed Impeller

The EKJ-802S uses a closed impeller configuration.

This is well suited to relatively clean water where hydraulic efficiency and pressure generation are important.

Recommended applications include:

  • Domestic water
  • Filtered rainwater
  • Clean well water
  • Garden irrigation
  • Storage tanks
  • Water transfer

Copper Motor Winding

The motor uses copper winding, which provides good electrical conductivity and supports reliable operation under normal load conditions.

The copper-wound motor is combined with built-in thermal protection for the single-phase configuration.

Built-In Thermal Protector

The EKJ-802S includes a built-in thermal protector.

This helps protect the motor from excessive temperature caused by abnormal operating conditions.

Suitable external electrical protection should still be installed, including:

  • Circuit breaker
  • Proper earthing
  • Correct cable size
  • Isolation switch
  • Appropriate electrical connections

Insulation Class F

The motor is specified with Class F insulation.

Class F insulation provides a higher thermal tolerance than lower insulation classes and is commonly used in motors intended for continuous-duty applications.

IPX4 Protection

The EKJ-802S motor has an IPX4 protection rating.

This provides protection against water splashing from different directions.

The pump should nevertheless be installed in a suitable dry and ventilated location and protected against flooding or submersion.

Maximum Water Temperature

The standard EKJ-802S specification lists a maximum liquid temperature of approximately +35°C.

It is therefore suitable for:

  • Cold water
  • Groundwater
  • Domestic water
  • Garden water
  • Irrigation water
  • Storage-tank water

It should not be used as a dedicated hot-water pump.

Garden Irrigation

The EKJ-802S is well suited to garden irrigation and landscape watering.

The approximately 40 m maximum head provides useful pressure for:

  • Garden sprinklers
  • Watering hoses
  • Small sprinkler networks
  • Greenhouse irrigation
  • Vegetable gardens
  • Landscape irrigation
  • Outdoor cleaning

The actual number of sprinklers that can run simultaneously depends on their individual flow and pressure requirements.

Domestic Water Pressurisation

LEO specifically positions the EKJ series for domestic water pressurisation.

The EKJ-802S can be used to increase water pressure from:

  • Storage tanks
  • Ground tanks
  • Shallow wells
  • Rainwater systems
  • Low-pressure water sources

For automatic operation, it can be paired with a suitable pressure controller, pressure switch or pressure tank.

Shallow-Well Water Supply

The EKJ-802S is suitable for shallow-well water lifting within its approximately 7–8 m suction capability.

For a well installation:

  1. Position the pump as close to the well as practical.
  2. Keep the suction line short.
  3. Use an appropriately sized suction pipe.
  4. Install a suitable foot valve.
  5. Seal every suction connection against air leakage.
  6. Prime the pump before initial operation.
  7. Ensure the water level does not fall below the pump's practical suction limit.

Water Tank Transfer

The pump can also be used for transferring clean water between tanks.

Typical configurations include:

  • Ground-level tank → elevated tank
  • Rainwater tank → irrigation system
  • Storage tank → domestic supply
  • Reservoir → garden irrigation
  • Underground tank → household water system

The total vertical lift and piping resistance must remain within the pump's operating range.

Deep-Well Application Clarification

The product category may describe the EKJ-802S as a “deep well / garden jet pump”, but technically its maximum suction is only around 7–8 m.

Therefore, the EKJ-802S should be considered primarily a:

Garden / shallow-well / domestic self-priming jet pump

rather than a true deep-well pump.

For wells where the water level is substantially deeper than the practical suction limit, a dedicated LEO AJDM deep-well jet pump with an ejector system is more appropriate.

EKJ-802S vs EKJ-802P

Feature EKJ-802S EKJ-802P
Motor Power 0.8 kW 0.8 kW
Voltage 220–240 V 220 V
Max Flow 60–62 L/min Approx. 60 L/min
Max Head 38–40 m Approx. 40 m
Max Suction 7–8 m Approx. 8 m
Inlet/Outlet 1" × 1" 1" × 1"
Pump Body Stainless Steel Plastic/Polymer
Shaft AISI 304 SS AISI 304 SS
Impeller Technopolymer/PPO Closed
Main Application Domestic / Garden Domestic / Garden
Construction Stainless-Steel Version Standard Version

The EKJ-802S is particularly attractive where a stainless-steel pump body is preferred for durability and corrosion resistance. LEO's technical documentation identifies the S series specifically as the stainless-steel jet-pump configuration.

Key Advantages

The LEO EKJ-802S offers:

  1. 0.8 kW motor
  2. Approximately 1.0–1.1 HP
  3. 220–240 V single-phase operation
  4. 50 Hz frequency
  5. Self-priming jet-pump design
  6. 60–62 L/min maximum flow
  7. 38–40 m maximum head
  8. 7–8 m maximum suction
  9. 1" × 1" connections
  10. Stainless-steel pump body
  11. AISI 304 stainless-steel shaft
  12. Technopolymer/PPO closed impeller
  13. Copper motor winding
  14. Class F insulation
  15. Built-in thermal protection
  16. IPX4 protection
  17. Maximum liquid temperature +35°C
  18. Compact surface-mounted design
  19. Suitable for garden irrigation
  20. Suitable for domestic water pressurisation
  21. Suitable for shallow-well pumping
  22. Suitable for tank transfer
  23. Suitable for small irrigation systems.

Recommended Applications

Domestic Water Supply: Suitable for supplying clean water to homes and small buildings where the required flow and pressure fall within the pump curve.

Garden Irrigation: Suitable for sprinklers, hoses, greenhouses, vegetable gardens and landscape irrigation.

Shallow Wells: Suitable for lifting clean groundwater from shallow wells within the specified suction limit.

Water Tank Transfer: Suitable for transferring clean water between storage tanks.

Pressure Boosting: Suitable for increasing water pressure from tanks and other low-pressure water sources.

Rainwater Systems: Can be used for filtered rainwater for non-potable applications such as garden irrigation.

Installation Recommendations

For reliable operation:

  • Install the pump on a firm and level base.
  • Position it as close as possible to the water source.
  • Keep suction lift within the manufacturer's limit.
  • Use an appropriate suction-pipe diameter.
  • Keep the suction line as short and straight as practical.
  • Install a suitable foot valve/check valve.
  • Ensure all suction joints are completely airtight.
  • Prime the pump before first operation.
  • Never operate the pump dry.
  • Avoid pumping water containing excessive sand or abrasive particles.
  • Provide appropriate electrical protection and earthing.
  • Keep the motor ventilated.
  • Protect the pump from flooding and direct immersion.

Product Description

LEO EKJ-802S 0.8kW Stainless-Steel Self-Priming Garden Jet Pump is a compact and durable surface-mounted water pump designed for domestic water supply, garden irrigation, shallow-well water lifting, water tank transfer and pressure boosting. Powered by a 220–240 V single-phase 800 W motor, the pump provides approximately 60–62 L/min maximum flow and 38–40 m maximum head, with a maximum suction capability of approximately 7–8 m.

The EKJ-802S features a stainless-steel pump body, AISI 304 stainless-steel shaft, technopolymer/PPO closed impeller, copper motor winding, Class F insulation, built-in thermal protection and IPX4 protection. Its self-priming jet design makes it suitable for clean-water applications where the water source is below the pump and within the practical suction limit.

With its 1" × 1" connections and approximately 40 m maximum head, the LEO EKJ-802S is a practical choice for home water systems, garden sprinklers, shallow wells, irrigation networks, water tanks and general clean-water transfer.

SEO Product Title

LEO EKJ-802S 0.8kW 1HP 220V Stainless Steel Self-Priming Garden Jet Pump 40m Head

Short Product Description

LEO EKJ-802S is a 0.8kW / approximately 1HP 220V stainless-steel self-priming garden jet pump designed for domestic water supply, garden irrigation, shallow-well pumping, water tank transfer and pressure boosting. It provides approximately 60–62 L/min maximum flow, 38–40 m maximum head and 7–8 m maximum suction, with 1" × 1" inlet and outlet connections. The pump features an AISI 304 stainless-steel body and shaft, technopolymer/PPO closed impeller, copper motor winding, Class F insulation, built-in thermal protection and IPX4 protection, making it suitable for reliable clean-water pumping in residential, garden and small irrigation systems.



 Inquiry - LEO JET PUMPS FOR DEEP WELL, GARDEN JET PUMPS - EKJ-802S