The LEO AKSm 130W is a compact automatic self-priming peripheral water pump designed for domestic water supply, small water-transfer systems, garden irrigation and automatic sprinkler applications. It incorporates a 2 L pressure tank and automatic pressure-control system, allowing the pump to start and stop automatically according to water demand. LEO specifies the AKSm series for clean water and liquids with similar physical and chemical properties.
For the AKSm130 / 130W variant, published Malaysian specifications list a maximum flow of approximately 30 L/min, maximum head of 28 m, maximum suction of 9 m, 1" × 1" inlet/outlet, and 220–240 V single-phase operation.
Technical Specifications
| Specification | LEO AKSm 130W |
|---|---|
| Brand | LEO |
| Model | AKSm 130W / AKSm130 |
| Pump Type | Automatic Self-Priming Peripheral Pump |
| Motor Power | 130 W |
| Motor Output | Approx. 0.17 HP |
| Voltage | 220–240 V |
| Phase | Single Phase |
| Frequency | 50 Hz |
| Maximum Flow | 30 L/min |
| Maximum Flow | Approx. 1.8 m³/h |
| Maximum Head | 28 m |
| Maximum Suction | 9 m |
| Inlet | 1" |
| Outlet | 1" |
| Pressure Tank | 2 L |
| Impeller | Brass |
| Pump Bonnet | Brass |
| Shaft | AISI 304 Stainless Steel |
| Motor Winding | Copper |
| Bearing | C&U |
| Thermal Protection | Built-In |
| Insulation Class | F |
| Protection Class | IP44 |
| Maximum Liquid Temperature | 40°C |
| Maximum Ambient Temperature | 40°C |
| Automatic Operation | Yes |
| Automatic Pressure Sensor | Yes |
| Low-Flow Control | Yes |
| Dry-Run / No-Water Stop | Yes |
| Start Delay | 3 seconds |
| Pressure Tank | 2 L |
The AKSm series is documented as a self-priming peripheral pump with brass hydraulic components, AISI 304 shaft, automatic pressure sensing, low-flow control and automatic stopping when water is unavailable.
130 W Motor
The AKSm130 is equipped with a compact 130 W motor, with Malaysian product information identifying the output as approximately 0.17 HP.
The relatively low motor power makes the pump suitable for small domestic applications where the objective is to provide automatic water pressure without using a larger conventional booster pump.
Typical applications include:
- Household water supply
- Garden watering
- Small irrigation systems
- Water tank distribution
- Automatic sprinkler systems
- Small water-transfer applications
- Utility water systems
Self-Priming Peripheral Design
The AKSm is specifically classified as a self-priming peripheral pump.
The self-priming arrangement makes it suitable for installations where the pump is positioned above the water source and must draw water through a suction line.
The peripheral hydraulic design provides relatively high head from a compact motor, making it appropriate for small-volume applications where pressure is more important than very high flow.
30 L/min Maximum Flow
The AKSm130 has a published maximum flow of approximately 30 L/min, equivalent to about 1.8 m³/h.
This capacity is appropriate for small domestic water-demand applications such as:
- Bathroom taps
- Kitchen taps
- Garden hoses
- Small sprinklers
- Utility outlets
- Water tank distribution
The actual flow depends on the total dynamic head of the installation.
As system resistance increases, the available flow decreases.
28 m Maximum Head
The AKSm130 is specified with a maximum head of 28 m.
A 28 m water head corresponds to approximately 2.75 bar of theoretical static pressure.
The maximum head is achieved at very low or zero flow and should not be interpreted as the operating pressure available at 30 L/min.
For correct pump selection, the system should be evaluated using:
Static head + pipe friction + fittings + required outlet pressure = Total Dynamic Head
9 m Maximum Suction
The AKSm130 has a published maximum suction of 9 m, which is particularly useful for shallow-well and storage-tank applications.
The suction capability depends on actual installation conditions, including:
- Water level
- Suction-pipe length
- Pipe diameter
- Number of elbows
- Foot valve
- Air leakage
- Water temperature
- Atmospheric pressure
The suction pipe should be properly sealed and installed with as little restriction as practical.
2 L Pressure Tank
A major feature of the AKSm130 is its integrated 2 L pressure tank.
The small pressure tank helps the pump operate automatically and can reduce unnecessary pump starts during very small water-demand events.
The basic operating principle is:
Water outlet closed → pressure maintained → pump stopped
Water outlet opened → pressure drops → pump starts
Water outlet closed → pressure restored → pump stops
This provides convenient automatic water-pressure management for small household installations.
Automatic Pressure Sensor
The AKSm series incorporates an automatic pressure sensor.
The sensor detects changes in system pressure and controls pump operation according to water demand.
This eliminates the need for the user to manually switch the pump on and off during normal operation.
3-Second Start Delay
LEO's AKSm documentation specifies a 3-second delay before pump start after connection to the electrical supply. This is intended to reduce potential danger associated with electrical sparks.
The delayed start is particularly relevant to an automatic pump because the unit can start without the user directly operating a conventional switch.
Automatic Small-Flow Control
The AKSm includes an automatic switch to small-flow control when the water flow becomes low.
This helps the pump respond appropriately to small water demands and contributes to more stable automatic operation.
This is useful for applications such as:
- Slowly opened taps
- Small household outlets
- Minor irrigation flow
- Small leakage detection/control situations
Automatic No-Water Stop
The AKSm series is designed to automatically stop after detecting a no-water condition, with LEO documentation specifying approximately 6 minutes in the event of no water inside the pump.
This helps reduce the risk of prolonged operation without an adequate water supply.
Proper installation is still essential, and the pump should not be intentionally operated dry.
Brass Impeller
The AKSm uses a brass impeller.
Brass provides good mechanical strength and corrosion resistance for normal clean-water applications.
The impeller is the primary rotating hydraulic component responsible for generating water flow and pressure.
Brass Pump Bonnet
The pump bonnet is also specified as brass.
The brass hydraulic construction provides good resistance to corrosion and is suitable for clean-water domestic applications.
AISI 304 Stainless-Steel Shaft
The pump uses an AISI 304 stainless-steel shaft.
The shaft transfers rotational power from the motor to the impeller while operating in the pump's wet environment.
AISI 304 provides good corrosion resistance for normal fresh-water service.
Copper Motor Winding
The motor uses copper winding.
Copper provides good electrical conductivity and supports efficient and reliable motor operation.
The pump should be connected to the specified 220–240 V supply with appropriate electrical protection.
Built-In Thermal Protector
The single-phase motor incorporates a built-in thermal protector.
This protects the motor against excessive temperature caused by abnormal operating conditions.
Potential causes of motor overheating include:
- Overloading
- Mechanical blockage
- Incorrect voltage
- Insufficient ventilation
- Excessive ambient temperature
- Abnormal operating conditions
The thermal protector is supplementary to proper electrical circuit protection.
Class F Insulation
The motor is specified with Class F insulation.
This provides suitable thermal resistance for normal pump operation.
IP44 Protection
The AKSm130 is listed with IP44 protection.
This provides protection against solid objects of the applicable size and splashing water.
The pump should still be installed in a protected, dry location and should not be submerged or exposed to continuous high-pressure water.
1" × 1" Connections
The pump uses standard 1-inch inlet and 1-inch outlet connections.
These connections are suitable for common domestic plumbing systems.
For good suction performance:
- Use a suitable suction pipe.
- Keep the suction line as short as possible.
- Avoid unnecessary elbows.
- Ensure all joints are airtight.
- Use an appropriate foot valve/check valve where required.
- Avoid undersized suction piping.
Maximum Liquid Temperature: 40°C
The AKSm130 is specified for a maximum liquid temperature of 40°C.
It is therefore primarily intended for normal-temperature clean-water applications such as:
- Domestic water
- Garden water
- Tank water
- Irrigation water
- General utility water
It should not be used for hot-water applications exceeding the manufacturer's specified temperature.
Maximum Ambient Temperature: 40°C
The motor is specified for a maximum ambient temperature of approximately 40°C.
Adequate ventilation is important, especially when the pump is installed in an enclosed pump room or cabinet.
Domestic Water Supply
The AKSm130 is designed for small domestic water-supply systems. LEO specifically identifies the AKSm series for small living-water supply.
Typical applications include:
- Household taps
- Kitchen water
- Bathroom water
- Outdoor taps
- Small utility outlets
- Water tank distribution
Its automatic pressure-control function makes it particularly convenient for domestic use.
Garden Irrigation
The AKSm130 is suitable for small garden irrigation applications.
It can be used for:
- Garden hoses
- Small sprinklers
- Flower beds
- Vegetable gardens
- Landscape watering
- Small greenhouse irrigation
The 30 L/min maximum flow is suitable for modest irrigation requirements.
Automatic Sprinkler Systems
LEO specifically lists automatic water sprinkler systems among the applications of the AKSm series.
The integrated pressure control allows the pump to operate automatically when the sprinkler system requires water.
The sprinkler system should be checked to ensure its required flow and pressure are compatible with the AKSm130 performance.
Water Tank Applications
The AKSm130 can be used with storage tanks where automatic water supply is required.
Typical arrangement:
Storage Tank → AKSm130 → Household / Garden Distribution
The 9 m maximum suction provides useful flexibility for installations where the pump is located above the water level.
Shallow-Well Applications
The self-priming configuration and 9 m maximum suction make the pump suitable for certain shallow-well installations.
However, the actual available suction lift can be lower than the theoretical maximum because of:
- Pipe friction
- Air leakage
- Water temperature
- Altitude
- Foot-valve losses
- Suction-pipe diameter
The pump should therefore be installed as close to the water source as practical.
Clean-Water Applications
The AKSm series is designed for clean water or liquids with similar physical and chemical characteristics.
Suitable applications include:
- Fresh water
- Clean tank water
- Filtered rainwater
- Clean irrigation water
- Utility water
It should not be used for:
- Sewage
- Mud
- Sludge
- Abrasive slurry
- Fibrous wastewater
- Heavy sediment
- Liquids containing large solids
A suitable filter should be installed if the water contains suspended particles.
Compact Automatic Pumping System
Unlike a conventional standalone peripheral pump, the AKSm130 integrates several components needed for automatic operation:
- Self-priming peripheral hydraulic system
- Pressure sensor
- 2 L pressure tank
- Automatic control
- Low-flow control
- No-water protection
- Thermal protection
This makes it a convenient compact solution for small residential water-pressure applications.
Main Applications
The LEO AKSm130 is suitable for:
- Domestic water supply
- Household pressure boosting
- Garden irrigation
- Automatic sprinkler systems
- Water tank supply
- Shallow-well water supply
- Rainwater distribution
- Small agricultural irrigation
- Landscape watering
- Utility water transfer
- Small air-conditioning support systems
- General clean-water applications
Key Advantages
The LEO AKSm 130W provides:
- 130 W motor
- Approx. 0.17 HP
- 220–240 V single-phase supply
- 30 L/min maximum flow
- 28 m maximum head
- 9 m maximum suction
- 2 L pressure tank
- Automatic pressure control
- Automatic start/stop
- 3-second start delay
- Low-flow automatic control
- Automatic no-water stop
- Brass impeller
- Brass pump bonnet
- AISI 304 stainless-steel shaft
- Copper motor winding
- C&U bearing
- Built-in thermal protector
- Class F insulation
- IP44 protection
- 1" × 1" connections
- Maximum liquid temperature of 40°C
- Suitable for clean-water applications
AKSm130 vs Standard APm37
| Specification | AKSm130 | APm37 |
|---|---|---|
| Pump Type | Self-Priming Peripheral | Peripheral |
| Motor Power | 130 W / 0.17 HP | 370 W / 0.5 HP |
| Max Flow | 30 L/min | Up to approx. 40 L/min |
| Max Head | 28 m | Up to approx. 40 m |
| Max Suction | 9 m | 8 m |
| Pressure Tank | 2 L | No |
| Automatic Pressure Control | Yes | No |
| Self-Priming | Yes | Standard peripheral design |
| Impeller | Brass | Brass |
| Shaft | AISI 304 | AISI 304 |
| Application | Small automatic water supply | General water pumping |
The AKSm130 is therefore better suited when automatic pressure control and self-priming operation are important, whereas the APm37 is a more conventional peripheral pump for applications where an external control system may be used. LEO separately classifies its AKSm range as Self-Priming Peripheral Pump.
Installation Recommendations
For reliable operation:
- Install the pump on a firm, level base.
- Position it as close to the water source as practical.
- Keep the suction pipe short and direct.
- Ensure every suction connection is completely airtight.
- Use suitable 1" pipework.
- Install a suitable foot valve/check valve where required.
- Ensure adequate water is available.
- Do not intentionally operate the pump dry.
- Keep the pump protected from flooding.
- Provide adequate ventilation around the motor.
- Install suitable electrical protection and earthing.
- Clean filters regularly.
- Keep the pump accessible for maintenance.
Important Specification Note
There is some model-number variation in online catalogues. LEO's AKSm family documentation identifies the series as self-priming peripheral pumps, while the Malaysian AKSM-130 listing gives the specific 130W-class product as 0.17 HP, 30 L/min, 28 m head and 9 m suction.
For your website listing, I recommend using the specifications printed on the actual pump nameplate and supplied LEO datasheet if they differ from the online listing.
Product Description
LEO AKSm 130W Automatic Self-Priming Peripheral Water Pump is a compact and efficient automatic pump designed for domestic water supply, garden irrigation, automatic sprinklers, water tank systems, shallow-well applications and clean-water transfer. Powered by a 130W / approximately 0.17HP single-phase motor, it delivers up to 30 L/min flow, 28 m maximum head and 9 m maximum suction, with standard 1" × 1" inlet and outlet connections.
The AKSm130 incorporates a 2 L pressure tank, automatic pressure sensor, low-flow control, 3-second delayed start and automatic no-water protection for convenient automatic operation. Its construction includes a brass impeller, brass pump bonnet, AISI 304 stainless-steel shaft, copper motor winding, C&U bearing, built-in thermal protector, Class F insulation and IP44 protection.
With its compact construction and integrated automatic control system, the LEO AKSm130 is a practical solution for small residential and garden water systems requiring automatic pressure boosting and self-priming capability.
SEO Product Title
LEO AKSm 130W 0.17HP Automatic Self-Priming Peripheral Water Pump – 30L/min, 28m Head
Short Product Description
LEO AKSm 130W is an automatic self-priming peripheral water pump designed for domestic water supply, garden irrigation, automatic sprinkler systems and water tank applications. It provides 30 L/min maximum flow, 28 m maximum head and 9 m maximum suction, with 1" × 1" connections and a built-in 2 L pressure tank. Features include automatic pressure control, low-flow control, 3-second delayed start, automatic no-water protection, brass impeller and bonnet, AISI 304 stainless-steel shaft, copper winding, thermal protection, Class F insulation and IP44 protection.
Inquiry - LEO PERIPHERAL, SELF-PRIMING PERIPEHRAL PUMPS - AKSM 130W