The LEO LSWM 50A is a compact automatic 0.5 HP / 0.37 kW sewage submersible pump designed for wastewater drainage, sewage pits, septic tanks, drainage stations and general dirty-water pumping. It operates on 220 V / 50 Hz single-phase power, with a 1½-inch (G1½) outlet, a maximum flow of approximately 217 L/min, and a maximum head of 11 m according to Malaysian product specifications.
LEO's current European technical documentation lists the closely corresponding LSWm50(A) at 0.37 kW / 0.5 HP, 220 V/50 Hz, G1.5 outlet, 16 m³/h maximum flow and 9.5 m maximum head, with a maximum particle diameter of 20 mm. The difference in maximum flow/head figures reflects different catalog/market specifications, so the pump nameplate and regional datasheet should be treated as the final reference for a specific unit.
Product Specifications
| Specification | Details |
|---|---|
| Brand | LEO |
| Model | LSWM 50A |
| Pump Type | Automatic Sewage Submersible Pump |
| Motor Power | 0.37 kW |
| Motor Rating | 0.5 HP |
| Voltage | 220 V |
| Frequency | 50 Hz |
| Phase | Single Phase |
| Maximum Flow | Approx. 217 L/min |
| Maximum Flow | Approx. 13.0 m³/h |
| Maximum Head | 11 m |
| Outlet Size | 1½" / G1½ |
| Maximum Particle Size | 20 mm |
| Maximum Immersion Depth | 5 m |
| Maximum Liquid Temperature | 40°C |
| Liquid pH Range | 4–10 |
| Motor Winding | Copper |
| Shaft Material | AISI 304 Stainless Steel |
| Pump Body | AISI 304 Stainless Steel |
| Handle Material | AISI 304 Stainless Steel |
| Thermal Protection | Built-In |
| Insulation Class | F |
| Protection Class | IPX8 / IP68 class |
| Operation | Automatic Start/Stop |
| Level Control | Float Switch |
| Installation | Fully Submersible |
The Malaysian specification lists 217 L/min, 11 m head, 0.37 kW / 0.5 HP and a 1½-inch outlet. It also identifies the AISI 304 fabricated shaft, handle and pump body, built-in thermal protection, float-switch operation and Class F insulation.
0.5 HP / 0.37 kW Motor
The LSWM50A uses a 0.37 kW / 0.5 HP single-phase motor, providing more capacity than the smaller LSWM25A while retaining a compact submersible design.
The motor operates from a standard 220 V / 50 Hz supply and incorporates a built-in thermal protector. The thermal protection helps reduce the risk of motor damage caused by excessive temperature during overload or abnormal operating conditions.
For permanent installations, appropriate circuit protection should still be provided in accordance with the electrical installation requirements.
High-Flow Wastewater Drainage
The Malaysian LSWM50A specification gives a maximum flow of approximately 217 L/min, equivalent to around 13.0 m³/h.
This provides useful capacity for:
- Sewage collection pits
- Wastewater tanks
- Septic tanks
- Basement drainage
- Commercial drainage
- Small industrial wastewater systems
- Construction-site drainage
- Agricultural wastewater
LEO's newer European technical sheet lists the LSWm50(A) at up to 16 m³/h, illustrating why the exact regional/model configuration should be checked before publishing a single performance curve.
11-Metre Maximum Head
The commonly supplied Malaysian LSWM50A specification provides a maximum head of 11 metres.
This makes it suitable for wastewater applications requiring moderate vertical lifting, such as:
- Basement drainage
- Sewage pits
- Collection tanks
- Septic systems
- Small wastewater transfer stations
- Drainage systems with elevated discharge points
The maximum head should not be interpreted as the operating head at maximum flow. As the total system head increases, actual flow decreases.
For correct pump selection, calculate:
Total Dynamic Head = Static Lift + Pipe Friction + Fitting Losses + Discharge Pressure Requirement
1½-Inch Discharge Outlet
The LSWM50A uses a 1½-inch / G1½ discharge connection.
The outlet size is appropriate for the pump's relatively compact design and flow capacity. The discharge hose or pipe should be selected according to the required duty flow and total pipe length.
Using a significantly smaller hose can increase friction losses and reduce the actual flow delivered by the pump.
20 mm Particle Handling
The current LEO technical documentation specifies a maximum particle diameter of 20 mm for the LSWm50A.
This makes the pump suitable for wastewater containing suspended solids and small debris, unlike a conventional clean-water pump.
However, a maximum particle diameter does not mean the pump should be used to process large solid objects, ropes, cloth, plastic bags or long fibrous materials. Such materials can cause clogging or impeller problems.
Where significant debris is present, an upstream screening arrangement is recommended.
Automatic Float-Switch Operation
The “A” version is designed for automatic operation using a float switch. LEO's documentation explicitly identifies automatic operation with a float switch for the LSW series.
The basic operation is:
Water level rises → Float rises → Pump starts → Water level falls → Float falls → Pump stops
This is particularly useful for sewage pits and wastewater collection tanks because the pump can automatically respond to changes in liquid level without requiring manual switching.
Stainless-Steel Construction
One of the key features of the LSWM50A is its AISI 304 stainless-steel fabricated shaft, handle and pump body.
Stainless-steel construction provides useful corrosion resistance in wet and wastewater environments and makes the pump suitable for regular submerged operation.
The shaft and mechanical-seal assembly also help isolate the motor from the pumped liquid.
Built-In Thermal Protection
The LSWM50A incorporates a built-in thermal protector.
This protection is designed to respond to excessive motor temperature, helping protect the motor winding under abnormal operating conditions.
Thermal protection does not eliminate the need for correct pump selection. The pump should still be operated within the specified hydraulic, temperature and immersion limits.
IPX8 / IP68-Class Submersible Protection
The current LEO technical sheet specifies IPX8 protection for the LSW range, while Malaysian listings describe the pump as a submersible unit and earlier LEO documentation commonly uses IP68 terminology.
For product catalog purposes, it is appropriate to describe the LSWM50A as an IPX8/IP68-class submersible pump, while the exact rating printed on the supplied unit should be used for formal technical documentation.
Operating Conditions
The LSW series is intended for operation within defined limits. Key conditions include:
- Maximum liquid temperature: 40°C
- Maximum immersion depth: 5 m
- Liquid pH: approximately 4–10
- Maximum particle size: 20 mm
- Supply: 220 V / 50 Hz single phase
- Insulation: Class F
- Protection: IPX8-class submersible design
The pump should not be used with highly corrosive chemicals, excessive abrasive solids or liquids outside the specified temperature and chemical compatibility range without confirmation from LEO.
Suitable Applications
LEO identifies the LSW series for wastewater drainage and sewage pumping applications. The Malaysian LSWM50A listing specifically identifies:
Residential
- Septic tanks
- Residential drainage stations
- Sewage collection pits
- Basement wastewater
Commercial
- Commercial facility drainage
- Wastewater collection tanks
- Building drainage systems
Industrial
- Factory wastewater drainage
- Industrial collection pits
- General wastewater transfer
Construction
- Construction-site drainage
- Excavation drainage
- Temporary wastewater removal
Municipal
- Sewage-treatment plant drainage
- Municipal drainage stations
- Wastewater collection systems
Agricultural
- Farm wastewater
- Methane pools
- Countryside field irrigation
LEO's own SW-series application information additionally identifies wastewater drainage from attenuation tanks, purification tanks and sewage tanks, as well as wastewater containing fibrous additives from leather and food-processing facilities.
Typical Installation
A typical installation is:
Sewage / wastewater collection pit → LEO LSWM50A → 1½" discharge pipe → drainage / treatment / collection point
The pump should be positioned securely inside the collection pit, with adequate clearance around the suction area.
The float switch should be free to move vertically and should not become trapped against the pit wall, discharge pipe or other equipment.
For permanent wastewater installations, a suitable non-return valve may be incorporated into the discharge line to reduce backflow when the pump stops.
Pump Performance Considerations
The 217 L/min maximum flow and 11 m maximum head are maximum performance specifications and should not be considered simultaneous operating conditions.
For example, if the system requires significant vertical lifting plus a long discharge pipe, the actual operating flow will be considerably lower than the maximum-flow figure.
Before installation, determine:
- Required flow rate.
- Static vertical lift.
- Discharge pipe diameter.
- Total discharge-pipe length.
- Number of elbows and valves.
- Required discharge pressure.
- Type and concentration of suspended solids.
- Required automatic operating level.
The pump should then be matched to its performance curve at the required duty point.
Main Product Advantages
- 0.5 HP / 0.37 kW motor for compact wastewater systems.
- Up to 217 L/min flow in the commonly supplied Malaysian configuration.
- 11 m maximum head for moderate-lift drainage.
- 1½-inch / G1½ outlet for compact discharge installations.
- 20 mm maximum particle size for wastewater containing suspended solids.
- Automatic float-switch operation for automatic start/stop.
- Built-in thermal protector for motor protection.
- AISI 304 stainless-steel shaft for corrosion resistance.
- AISI 304 stainless-steel pump body and handle in the listed Malaysian configuration.
- Class F insulation for improved motor thermal performance.
- IPX8/IP68-class submersible protection.
- 5 m maximum immersion depth.
- Suitable for residential, commercial, industrial, construction, municipal and agricultural wastewater applications.
- Compact automatic design suitable for sewage pits, drainage tanks and wastewater collection systems.
Product Details Summary
The LEO LSWM50A is a 0.5 HP / 0.37 kW automatic sewage submersible pump designed for wastewater, sewage and dirty-water drainage. The commonly supplied Malaysian configuration operates at 220 V / 50 Hz single phase, delivering up to 217 L/min with a maximum head of 11 metres through a 1½-inch / G1½ outlet. The pump can handle suspended particles up to approximately 20 mm and features automatic float-switch operation, built-in thermal protection, Class F insulation and AISI 304 stainless-steel shaft, handle and pump body. It is suitable for residential sewage pits, septic tanks, construction sites, factories, commercial facilities, municipal sewage-treatment drainage, agricultural wastewater and general wastewater collection systems.
SEO Product Title
LEO LSWM50A Sewage Submersible Pump 0.5HP 0.37kW – 217L/min, 11M Head
SEO Product Description
LEO LSWM50A Sewage Submersible Pump is an automatic 0.5HP / 0.37kW wastewater and sewage pump designed for reliable drainage of dirty water, sewage and wastewater containing suspended solids. Operating at 220V/50Hz single phase, it provides up to 217L/min flow with a maximum head of 11 metres and features a 1½-inch / G1½ discharge outlet. The pump supports particles up to 20mm and incorporates an automatic float switch, built-in thermal protector, Class F insulation and AISI 304 stainless-steel shaft, handle and pump body. Its compact submersible construction makes it suitable for septic tanks, sewage pits, residential drainage stations, factories, construction sites, commercial facilities, municipal sewage-treatment systems and agricultural wastewater applications.
Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - LSWM 50A