B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO SEWAGE SUBMERSIBLE PUMPS - QDX 1.5-25-0.55LA



The LEO QDX 1.5-25-0.55LA is a compact 0.75 HP / 0.55 kW single-phase submersible drainage pump designed for water transfer, irrigation, accumulated-water drainage, construction dewatering and similar applications. The LA series uses a cast-iron pump body, aluminium motor casing, stainless-steel shaft and double-end mechanical seal. It is a drainage pump rather than a heavy-duty raw-sewage cutter pump, so it is intended for relatively clean or lightly contaminated water.

Product Specifications

Specification Details
Brand LEO
Model QDX 1.5-25-0.55LA
Pump Type Submersible Drainage Pump
Series QDX-LA
Motor Power 0.55 kW
Motor Rating 0.75 HP
Voltage 220 V
Frequency 50 Hz
Phase Single Phase
Maximum Flow Approx. 120 L/min*
Maximum Head Approx. 25 m*
Discharge Outlet 1"
Maximum Immersion Depth 5 m
Maximum Liquid Temperature 40°C
Permitted Liquid pH 6.5–8
Maximum Sand Content 0.1%
Suspended Solids Up to approx. 0.2 mm
Pump Body Cast Iron with Anti-Rust Treatment
Motor Housing Aluminium
Shaft Stainless Steel
Mechanical Seal Double-End Mechanical Seal
Motor Winding Copper
Insulation Class F
Protection Class IP68
Motor Protection Built-In Thermal Protector
Typical Applications Drainage, irrigation, wells, construction dewatering, aquaculture

*Performance values can vary slightly by regional specification and nameplate. Confirm the actual pump nameplate/performance curve for final engineering selection.

0.75 HP / 0.55 kW Motor

The QDX 1.5-25-0.55LA is equipped with a 0.55 kW / 0.75 HP single-phase motor, designed for operation from a standard 220 V / 50 Hz electrical supply.

Compared with the 0.37 kW QDX 1.5-15-0.37LA, this model provides higher motor output and is intended for applications requiring greater lifting height.

The motor incorporates copper windings and thermal protection to support reliable operation during normal pumping conditions.

High-Head Pumping

The key feature of the QDX 1.5-25-0.55LA is its higher head capability, with the model designation indicating approximately 25 m maximum head.

This makes it suitable where water must be lifted through a relatively significant vertical height, such as:

  • Deep drainage pits
  • Construction excavations
  • Water-storage tanks
  • Agricultural drainage
  • Irrigation systems
  • Wells
  • Basement drainage
  • General dewatering applications

Actual flow decreases as the discharge head increases. Therefore, the pump should be selected according to the required flow rate at the actual system head, rather than using the maximum head and maximum flow simultaneously.

Submersible Construction

The pump is designed to operate while completely submerged in the pumped liquid.

The submersible configuration offers several advantages:

  • No external priming is normally required.
  • The pump can be installed directly inside a drainage pit.
  • Water pressure at the inlet helps prevent suction problems.
  • The motor is cooled by the surrounding pumped liquid.
  • The installation is compact and suitable for confined spaces.

The maximum specified immersion depth should be observed during installation.

1-Inch Discharge Outlet

The QDX 1.5-25-0.55LA uses a 1-inch discharge connection.

The relatively small discharge size keeps the pump compact while allowing it to generate the higher head associated with this model.

For best performance, the discharge hose or pipe should be correctly sized and kept as short and direct as practical. Excessive bends, long pipe runs and undersized hoses can significantly increase friction losses.

Cast-Iron Pump Body

The LA configuration uses a cast-iron pump body with anti-rust treatment.

Cast iron provides:

  • Good mechanical strength
  • High durability
  • Resistance to impact
  • Stable support for the hydraulic components
  • Suitability for demanding drainage environments

The anti-rust treatment helps protect the pump body from corrosion during normal water-pumping applications.

Aluminium Motor Housing

The motor casing is manufactured from aluminium.

Aluminium provides a relatively lightweight housing while allowing efficient transfer of heat away from the motor.

This helps keep the pump compact and practical for portable drainage applications.

Stainless-Steel Shaft

A stainless-steel shaft is used for the rotating assembly.

The shaft is continuously exposed to a wet environment during submerged operation, making corrosion resistance important.

The stainless-steel construction provides a combination of:

  • Corrosion resistance
  • Mechanical strength
  • Reliable shaft rotation
  • Long-term durability

Double-End Mechanical Seal

The QDX-LA series uses a double-end mechanical seal between the motor and hydraulic section.

The mechanical seal helps prevent the pumped liquid from entering the motor through the rotating shaft.

This is particularly important for a submersible pump because the motor is enclosed within the submerged pump assembly.

Copper Motor Winding

The motor uses copper winding, providing good electrical conductivity and suitable thermal characteristics for the motor.

The copper winding, thermal protector and Class F insulation work together to provide reliable operation under the manufacturer's specified operating conditions.

Built-In Thermal Protection

The motor incorporates a built-in thermal protector.

This protection helps prevent excessive motor temperature caused by conditions such as overload or abnormal operation.

However, proper electrical protection should still be provided at the installation, including correctly rated circuit protection, grounding and suitable cable sizing.

Class F Insulation

The motor is equipped with Class F insulation.

Class F insulation provides appropriate thermal resistance for the motor winding system and is suitable for the operating environment of a submersible drainage pump.

IP68 Protection

The pump is designed with IP68 protection for submerged operation.

This makes the QDX 1.5-25-0.55LA suitable for installation in:

  • Drainage pits
  • Water tanks
  • Wells
  • Construction excavations
  • Flooded areas
  • Agricultural drainage systems

IP68 protection does not mean unlimited submersion. The manufacturer's specified 5 m maximum immersion depth should still be observed.

Maximum Immersion Depth – 5 m

The pump can be installed at a maximum immersion depth of approximately 5 metres.

The pump should be securely positioned and should not be allowed to operate outside the manufacturer's specified installation conditions.

When installed in a pit, avoid positioning the pump directly in heavy sediment or abrasive deposits whenever possible.

Water Quality Requirements

The QDX series is intended primarily for clean water and lightly contaminated drainage water.

The specified operating conditions include approximately:

  • pH: 6.5–8
  • Maximum sand content: 0.1%
  • Maximum liquid temperature: 40°C
  • Suspended solids: up to approximately 0.2 mm

This is an important consideration when listing the product as a sewage pump.

The QDX 1.5-25-0.55LA does not have the cutter/shredder arrangement found on dedicated LEO sewage cutter pumps. It should therefore not be selected for wastewater containing large solids, rags, ropes, heavy fibrous material or other blockage-producing debris.

Maximum Liquid Temperature – 40°C

The maximum permitted liquid temperature is approximately 40°C.

The pump is therefore suitable for normal-temperature:

  • Drainage water
  • Irrigation water
  • Well water
  • Rainwater
  • Construction water
  • Lightly contaminated water

It is not intended for high-temperature industrial liquids.

Suitable Applications

The QDX 1.5-25-0.55LA is particularly suitable for applications where a compact submersible pump is required to transfer water through a relatively high discharge head.

Agricultural applications

  • Irrigation
  • Farm drainage
  • Well-water transfer
  • Agricultural water management

Construction applications

  • Excavation dewatering
  • Foundation drainage
  • Construction-site accumulated water
  • Temporary water removal

Residential applications

  • Basement drainage
  • Water-pit drainage
  • Tank emptying
  • Rainwater removal

Industrial applications

  • General accumulated-water drainage
  • Equipment-area drainage
  • Small water-transfer systems

Aquaculture

  • Tank drainage
  • Pond water transfer
  • General aquaculture water management

Typical Installation

A typical installation can be arranged as:

Water source / drainage pit → QDX 1.5-25-0.55LA → 1" discharge hose/pipe → drainage point

The pump is submerged directly into the water.

For portable applications, the pump can be placed in the drainage area when required and removed after the desired water level has been reached.

For permanent installations, the discharge pipe should be securely supported and protected against excessive vibration or mechanical loading.

Important Selection Note

Although the model may appear in retail catalogues under a "sewage submersible pump" category, the QDX 1.5-25-0.55LA is better classified technically as a submersible drainage pump.

It is intended for water and lightly contaminated liquids rather than heavy raw sewage.

For sewage containing:

  • Rags
  • Rope
  • Fibrous waste
  • Large solid particles
  • Heavy organic debris

a dedicated LEO sewage pump with appropriate solids-handling capability or a cutter/shredder model should be selected instead.

Main Product Advantages

  1. 0.75 HP / 0.55 kW motor.
  2. 220 V single-phase operation.
  3. High-head design for demanding drainage applications.
  4. Approximately 25 m maximum head.
  5. Compact 1-inch discharge outlet.
  6. Cast-iron pump body with anti-rust treatment.
  7. Aluminium motor housing.
  8. Stainless-steel shaft.
  9. Double-end mechanical seal.
  10. Copper motor winding.
  11. Built-in thermal protection.
  12. Class F motor insulation.
  13. IP68 submersible protection.
  14. Up to 5 m immersion depth.
  15. Up to 40°C liquid temperature.
  16. Suitable for irrigation, drainage, construction dewatering, wells and aquaculture.
  17. Compact design for portable and fixed installations.

Product Details Summary

The LEO QDX 1.5-25-0.55LA is a 0.75 HP / 0.55 kW single-phase submersible drainage pump designed for high-head water transfer, irrigation, construction dewatering and general drainage applications. Operating at 220 V / 50 Hz, the pump provides a maximum head of approximately 25 metres and uses a compact 1-inch discharge outlet. Its LA-series construction combines a cast-iron pump body with anti-rust treatment, aluminium motor housing, stainless-steel shaft and double-end mechanical seal, while the motor incorporates copper windings, Class F insulation and built-in thermal protection. With IP68 protection, a maximum immersion depth of approximately 5 metres and a maximum liquid temperature of 40°C, it is suitable for wells, drainage pits, agricultural irrigation, construction-site dewatering, tanks and aquaculture. It should be used for clean or lightly contaminated water rather than heavy raw sewage containing large solids or fibrous waste.

SEO Product Title

LEO QDX 1.5-25-0.55LA Submersible Drainage Pump 0.75HP 0.55kW – 25M Head

SEO Product Description

LEO QDX 1.5-25-0.55LA Submersible Drainage Pump is a compact 0.75HP / 0.55kW, 220V single-phase high-head submersible pump designed for water drainage, irrigation, well-water transfer, construction dewatering and general water-transfer applications. Featuring a durable cast-iron pump body with anti-rust treatment, aluminium motor housing, stainless-steel shaft and double-end mechanical seal, the pump provides reliable submerged operation with Class F insulation, built-in thermal protection and IP68 protection. With a maximum head of approximately 25 metres, compact 1-inch discharge outlet, maximum immersion depth of 5 metres and maximum liquid temperature of 40°C, the LEO QDX 1.5-25-0.55LA is suitable for agricultural drainage, construction sites, water pits, wells, tanks, aquaculture and general dewatering applications.



 Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - QDX 1.5-25-0.55LA