B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO SEWAGE SUBMERSIBLE PUMPS - QDX 1.5-32-0.75LA



The LEO QDX 1.5-32-0.75LA is a 1 HP / 0.75 kW single-phase submersible drainage pump designed for high-head water transfer, irrigation, well-water pumping, construction dewatering, agricultural drainage and aquaculture applications. The pump operates at 220 V / 50 Hz, uses a 1-inch / 25 mm discharge outlet, and has a published performance range of approximately 25–150 L/min with a head range of 32.5–8.5 m. LEO's own QDX-LA documentation identifies this model specifically for small irrigation and drainage equipment, rural wells, farming, construction drainage and aquaculture.

Importantly, although this product may be categorized commercially as a "sewage submersible pump," the QDX 1.5-32-0.75LA is technically a submersible drainage pump, not a heavy-duty sewage cutter pump. It is designed for clean or lightly contaminated water and allows suspended solids only up to approximately 0.2 mm.

Product Specifications

Specification Details
Brand LEO
Model QDX 1.5-32-0.75LA
Pump Series QDX-LA
Pump Type Submersible Drainage Pump
Motor Power 0.75 kW
Motor Rating 1.0 HP
Voltage 220 V
Frequency 50 Hz
Phase Single Phase
Maximum Flow 150 L/min
Maximum Flow 9 m³/h
Rated Flow 1.5 m³/h
Maximum Head 32.5 m
Rated Head 32 m
Minimum/Operating Head Approx. 8.5 m at maximum published flow
Discharge Outlet 1" / 25 mm
Maximum Immersion Depth 5 m
Maximum Liquid Temperature 40°C
Permitted Liquid pH 6.5–8
Maximum Sand Content 0.1%
Suspended-Solid Passage Up to 0.2 mm
Pump Body Cast Iron
Pump Body Treatment Anti-Rust Treatment
Motor Casing Aluminium
Motor Winding Copper
Shaft Stainless Steel
Mechanical Seal Double-End Mechanical Seal
Filter Stainless Steel
Insulation Class F
Protection Class IP68
Thermal Protection Built-In
Approx. Dimensions 245 × 194 × 385 mm
Typical Applications Irrigation, drainage, wells, construction, aquaculture

The LEO technical sheet lists 0.75 kW, 1.5 m³/h rated flow and 32 m rated head, while its performance data gives approximately 0–9 m³/h flow and 32.5–8.5 m head.

1 HP / 0.75 kW Motor

The QDX 1.5-32-0.75LA uses a 0.75 kW / 1 HP motor. It is designed for 220 V, 50 Hz single-phase operation.

This motor rating provides substantially more lifting capability than smaller QDX models such as the 0.37 kW and 0.55 kW versions.

The motor is suitable for applications where water needs to be transferred vertically through a relatively high head while maintaining a compact submersible configuration.

The motor incorporates copper winding and a built-in thermal protector for additional protection against excessive motor temperature.

High 32.5-Metre Maximum Head

One of the main advantages of this model is its relatively high head capability.

The technical data identifies:

  • Rated head: 32 m
  • Maximum head: 32.5 m
  • Flow at maximum published head: approximately 0
  • Flow at approximately 32 m: approximately 1.5 m³/h
  • Maximum published flow: approximately 9 m³/h at approximately 8.5 m head

This makes the QDX 1.5-32-0.75LA particularly useful for applications where vertical lifting is more important than extremely high flow.

Potential applications include:

  • Deep drainage pits
  • Elevated water tanks
  • Agricultural irrigation
  • Rural well-water transfer
  • Construction dewatering
  • Basement drainage
  • Long vertical discharge lines
  • Garden irrigation
  • Aquaculture systems

The 32.5 m maximum head should not be interpreted as the pump delivering its maximum flow at that height. Pump flow decreases as system head increases.

Hydraulic Performance

The published performance data provides the following approximate relationship:

Flow Head
0 L/min 32.5 m
25 L/min 31.5 m
50 L/min 28.5 m
75 L/min 24.5 m
100 L/min 20 m
125 L/min 15.5 m
150 L/min 8.5 m

These values show why the actual operating point must be considered when selecting the pump. For example, at around 100 L/min, the available head is approximately 20 m, rather than the maximum 32.5 m.

The actual site flow will also be affected by:

  • Vertical lift
  • Pipe length
  • Pipe diameter
  • Pipe friction
  • Elbows
  • Valves
  • Check valves
  • Hose restrictions
  • Other system fittings

150 L/min Maximum Flow

The QDX-LA catalogue gives a flow range of approximately 25–150 L/min, equivalent to approximately 1.5–9 m³/h.

The published performance curve gives the maximum flow at the lower end of the head range.

This makes the pump suitable for applications requiring a combination of:

Moderate water volume + relatively high lifting height.

It is therefore particularly useful for drainage and water-transfer applications where a standard low-head drainage pump would not provide sufficient lifting capability.

1-Inch / 25 mm Discharge

The QDX 1.5-32-0.75LA uses a 25 mm / 1-inch discharge outlet.

The compact discharge connection is suitable for the pump's hydraulic characteristics.

For best performance, the discharge pipe or hose should be selected carefully. A long run of undersized hose can create substantial friction loss and reduce the actual flow.

For high-head applications, it is particularly important to minimize unnecessary restrictions and sharp bends.

Cast-Iron Pump Body

The pump uses a cast-iron pump body with anti-rust treatment.

Cast iron provides:

  • High mechanical strength
  • Good resistance to impact
  • Durable hydraulic housing
  • Stable support for internal components
  • Suitable service life for drainage applications

The anti-rust treatment provides additional protection for the pump body during submerged operation.

Aluminium Motor Casing

The QDX-LA configuration uses an aluminium motor casing.

Aluminium is advantageous for a submersible pump because it combines relatively low weight with good heat-transfer properties.

This helps keep the overall pump compact while assisting motor heat dissipation.

Stainless-Steel Shaft

The pump incorporates a stainless-steel shaft. LEO specifies a stainless-steel shaft for the QDX-LA series.

The shaft is an important rotating component and is continuously exposed to the wet operating environment.

Stainless steel provides:

  • Corrosion resistance
  • Mechanical strength
  • Good dimensional stability
  • Reliable rotating performance
  • Long-term durability

Double-End Mechanical Seal

The QDX-LA construction uses a double-end mechanical seal.

The mechanical seal creates a barrier between the hydraulic section and the motor section, helping prevent water from reaching the motor through the rotating shaft.

This is particularly important because the complete pump is designed to operate submerged.

Stainless-Steel Filter

The QDX 1.5-32-0.75LA is specified with a stainless-steel filter.

The filter helps prevent unsuitable particles from entering the hydraulic section.

However, it should not be confused with a sewage solids-handling system. The model's published suspended-solid passage is only approximately 0.2 mm.

Copper Motor Winding

The motor uses copper winding, a feature specified for the QDX-LA series.

Copper provides good electrical conductivity and appropriate thermal characteristics for the motor winding.

This contributes to reliable motor performance when the pump is operated within its specified electrical and hydraulic conditions.

Built-In Thermal Protector

The QDX 1.5-32-0.75LA includes a built-in thermal protector.

The thermal protector helps protect the motor against excessive temperature caused by abnormal operating conditions.

However, the thermal protector should not replace proper electrical installation. A suitable circuit breaker, grounding system and correctly sized electrical cable should still be used.

Class F Insulation

The QDX-LA model is specified with Class F insulation.

Class F insulation provides suitable thermal resistance for the motor winding system and supports reliable operation under the manufacturer's specified conditions.

IP68 Protection

The pump has an IP68 protection rating, making it suitable for submerged operation.

This is appropriate for:

  • Wells
  • Drainage pits
  • Water tanks
  • Construction excavations
  • Flooded areas
  • Agricultural drainage
  • Aquaculture systems

Although the pump is IP68-rated, it still has a specified maximum immersion depth of 5 metres.

Maximum Immersion Depth – 5 m

The maximum recommended immersion depth is 5 metres.

The pump should be securely positioned at the bottom or appropriate operating level of the water source.

For dirty-water applications, avoid placing the pump directly into heavy sediment whenever possible. Excessive sand and abrasive particles can accelerate wear of the hydraulic components and mechanical seal.

Maximum Liquid Temperature – 40°C

The maximum specified liquid temperature is +40°C.

The pump is therefore intended for normal-temperature water rather than hot industrial fluids.

Suitable liquids include:

  • Fresh water
  • Irrigation water
  • Well water
  • Rainwater
  • Drainage water
  • Lightly contaminated water

Liquid pH and Sand Content

The QDX-LA series is designed for liquids with a pH range of approximately 6.5–8. Maximum sand content is specified at approximately 0.1%.

These restrictions are important for protecting the pump's mechanical seal and hydraulic components.

The pump should not be used continuously with highly abrasive sand-laden water beyond the manufacturer's specified limit.

Suspended-Solid Passage

The published QDX-LA specification allows suspended solids up to approximately 0.2 mm.

Therefore, this model is suitable for relatively clean or lightly contaminated drainage water.

It is not recommended for raw sewage containing:

  • Rags
  • Rope
  • Large fibrous material
  • Plastic waste
  • Large organic solids
  • Stones
  • Construction debris

For these applications, a dedicated sewage pump with larger solids passage or a cutter pump should be selected.

Applications

LEO identifies the QDX series for small electrical irrigation and drainage equipment, urban/rural well-water pumping, farming irrigation and drainage, garden irrigation, household water supply, industrial accumulated-water drainage, construction water supply/drainage, livestock breeding and aquaculture.

Agricultural applications

  • Farm irrigation
  • Agricultural drainage
  • Rural well-water pumping
  • Livestock water systems
  • Water transfer for farming

Construction applications

  • Excavation dewatering
  • Foundation drainage
  • Construction-site water removal
  • Accumulated-water drainage

Residential applications

  • Garden irrigation
  • Household water transfer
  • Basement drainage
  • Water tank drainage

Industrial applications

  • Industrial accumulated-water drainage
  • Utility water transfer
  • Equipment-area drainage

Aquaculture

  • Fish ponds
  • Aquaculture tanks
  • Pond drainage
  • Water circulation and transfer

Typical Installation

A typical system can be arranged as:

Well / drainage pit / water tank → LEO QDX 1.5-32-0.75LA → 1" discharge pipe → storage tank / irrigation system / drainage point

The pump is lowered into the water and the discharge line is connected to the pump outlet.

For permanent installation, the discharge pipe should be properly supported so that its weight is not transferred directly to the pump outlet.

For portable applications, the pump can be moved between drainage points as required.

Pump Positioning

Correct pump positioning is important for reliable operation.

The pump should:

  • Remain adequately submerged during operation.
  • Be positioned on a stable surface.
  • Avoid excessive sediment accumulation.
  • Have a free inlet area.
  • Avoid sharp bends immediately at the discharge outlet.
  • Not be suspended solely by the electrical cable.
  • Remain within the specified 5 m immersion depth.

The electrical cable should be protected against abrasion, cuts and mechanical damage.

Performance Selection

The 32.5 m maximum head is the shut-off or near-zero-flow end of the performance curve, while the 150 L/min maximum flow occurs at a substantially lower head.

For example:

  • At approximately 32.5 m head, flow approaches zero.
  • At approximately 28.5 m head, flow is around 50 L/min.
  • At approximately 20 m head, flow is around 100 L/min.
  • At approximately 8.5 m head, flow reaches around 150 L/min.

This makes the pump particularly useful where the system requires a relatively high lifting height but does not require extremely large flow.

Main Product Advantages

  1. 1 HP / 0.75 kW motor.
  2. 220 V / 50 Hz single-phase operation.
  3. Up to 150 L/min flow.
  4. Approximately 9 m³/h maximum flow.
  5. Approximately 32.5 m maximum head.
  6. 32 m rated head.
  7. Compact 1-inch / 25 mm discharge.
  8. Cast-iron pump body with anti-rust treatment.
  9. Aluminium motor casing.
  10. Copper motor winding.
  11. Stainless-steel shaft.
  12. Double-end mechanical seal.
  13. Stainless-steel filter.
  14. Built-in thermal protector.
  15. Class F insulation.
  16. IP68 protection.
  17. Maximum immersion depth of 5 m.
  18. Maximum liquid temperature of 40°C.
  19. Suitable for irrigation, drainage, well-water pumping, construction dewatering and aquaculture.
  20. Compact design for portable and fixed installations.

Product Details Summary

The LEO QDX 1.5-32-0.75LA is a 1 HP / 0.75 kW high-head submersible drainage pump designed for irrigation, well-water pumping, agricultural drainage, construction dewatering, garden watering, aquaculture and general water-transfer applications. Operating at 220 V / 50 Hz single phase, it provides a published flow range of approximately 25–150 L/min with a head range of 32.5–8.5 m, with a rated operating point of approximately 1.5 m³/h at 32 m head. The pump features a cast-iron anti-rust-treated body, aluminium motor casing, copper winding, stainless-steel shaft, stainless-steel filter and double-end mechanical seal. Built-in thermal protection, Class F insulation and IP68 protection provide additional protection for submerged operation. With a 1-inch discharge outlet, 5 m maximum immersion depth, 40°C maximum liquid temperature, pH range of 6.5–8 and 0.1% maximum sand content, it is well suited to clean and lightly contaminated water applications.

SEO Product Title

LEO QDX 1.5-32-0.75LA Submersible Drainage Pump 1HP 0.75kW – 32.5M Head

SEO Product Description

LEO QDX 1.5-32-0.75LA Submersible Drainage Pump is a high-head 1HP / 0.75kW, 220V single-phase submersible pump designed for agricultural irrigation, rural well-water pumping, construction dewatering, drainage, garden watering, aquaculture and general water-transfer applications. The pump provides up to 150L/min flow and approximately 32.5 metres maximum head, with a 1-inch / 25mm discharge outlet. It features a durable cast-iron pump body with anti-rust treatment, aluminium motor casing, copper winding, stainless-steel shaft, stainless-steel filter and double-end mechanical seal. The pump also incorporates built-in thermal protection, Class F insulation and IP68 protection, with a maximum immersion depth of 5 metres and maximum liquid temperature of 40°C. Designed for clean and lightly contaminated water with suspended solids up to approximately 0.2mm, the LEO QDX 1.5-32-0.75LA is an ideal high-head solution for drainage, irrigation, wells, construction sites and aquaculture applications.



 Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - QDX 1.5-32-0.75LA