B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO SEWAGE SUBMERSIBLE PUMPS - QDX 10-10-0.55LA



The LEO QDX 10-10-0.55LA is a 0.55 kW / 0.73 HP single-phase submersible drainage pump designed for high-volume water transfer, agricultural irrigation, rural well-water pumping, drainage, construction-site dewatering and aquaculture. It operates at 220 V / 50 Hz, uses a 40 mm (1½-inch) discharge outlet, and has a published hydraulic range of approximately 25–275 L/min, with head ranging from approximately 15.2 m down to 3.8 m.

Despite being commonly grouped under sewage or submersible pumps, the QDX-LA series is more accurately classified as a submersible drainage pump. LEO specifies a maximum suspended-solid passage of approximately 0.2 mm and maximum sand content of 0.1%, so this model is intended for clean or lightly contaminated water rather than heavy raw sewage containing large solids, rags or fibrous waste.

Product Specifications

Specification Details
Brand LEO
Model QDX 10-10-0.55LA
Pump Series QDX-LA
Pump Type Submersible Drainage Pump
Motor Power 0.55 kW
Motor Rating 0.73 HP
Voltage 220 V
Frequency 50 Hz
Phase Single Phase
Maximum Flow Approx. 275 L/min
Maximum Flow Approx. 16.5 m³/h
Rated Flow Approx. 167 L/min
Maximum Head Approx. 15.2–15.3 m
Rated Head Approx. 10 m
Discharge Outlet 1½" / 40 mm
Maximum Immersion Depth 5 m
Maximum Liquid Temperature 40°C
Liquid pH Range 6.5–8
Maximum Sand Content 0.1%
Suspended-Solid Passage Up to 0.2 mm
Pump Body Cast Iron HT200
Motor Casing Aluminium
Impeller Engineering Plastic / PPO
Shaft Stainless Steel
Mechanical Seal Double-End Mechanical Seal
Motor Winding Copper
Insulation Class F
Protection Class IP68
Thermal Protection Built-In
Typical Applications Irrigation, drainage, wells, construction, aquaculture

LEO's QDX-LA catalogue specifies 220 V, 25–275 L/min, 15.2–3.8 m head, 5 m immersion depth, 0.55 kW / 0.73 HP and 40 mm outlet for the QDX 10-10-0.55LA.

0.55 kW / 0.73 HP Motor

The QDX 10-10-0.55LA uses a 0.55 kW / 0.73 HP single-phase motor designed for a 220 V / 50 Hz electrical supply.

The motor is suitable for applications requiring a combination of moderate lifting height and relatively high water-transfer capacity. The QDX-LA design incorporates copper winding, built-in thermal protection, Class F insulation and IP68 protection.

The electrical supply should be properly protected with an appropriately rated circuit breaker and grounding system.

High-Flow 275 L/min Capacity

The manufacturer's catalogue lists a flow range of approximately 25–275 L/min for this model.

The maximum flow is equivalent to approximately:

275 L/min × 60 ÷ 1,000 = 16.5 m³/h

A separate technical source identifies approximately 267 L/min as the maximum operating flow and approximately 167 L/min as the nominal flow, reflecting differences in how the performance curve and operating point are reported.

For catalogue purposes, 275 L/min maximum flow / approximately 16.5 m³/h is the appropriate figure when following LEO's QDX-LA product table.

This high-flow characteristic makes the pump useful for:

  • Drainage pits
  • Pond drainage
  • Agricultural irrigation
  • Water tanks
  • Construction dewatering
  • Rural wells
  • Aquaculture
  • General water transfer

Approximately 15.2–15.3 m Maximum Head

The QDX 10-10-0.55LA has a published maximum head of approximately 15.2 m, with some LEO-related product references listing approximately 15.3 m. Its nominal/rated head is approximately 10 m.

The model is therefore particularly suited to applications where the required lifting height is moderate and a relatively high water flow is desired.

As with other centrifugal pumps, maximum flow and maximum head do not occur simultaneously. Increasing the total discharge head reduces the available flow.

Hydraulic Performance

LEO's published performance curve gives approximately the following values for the QDX 10-10-0.55LA:

Flow Approx. Head
0 L/min 13.2 m
33 L/min 13.2 m
67 L/min 13.3 m
100 L/min 12.7 m
133 L/min 11.8 m
167 L/min 10.0 m
200 L/min 8.2 m
233 L/min 7.0 m
267 L/min 5.0 m

This performance curve illustrates that the pump is particularly well matched to systems requiring around 8–12 m of total head, where useful flow remains available.

The actual operating point depends on:

  • Static lifting height
  • Pipe diameter
  • Pipe length
  • Hose diameter
  • Number of elbows
  • Valves
  • Check valves
  • Pipe friction
  • Water characteristics

1½-Inch / 40 mm Discharge Outlet

The pump is equipped with a 1½-inch / 40 mm discharge outlet.

The relatively large outlet allows the pump to transfer substantially more water than the smaller 25 mm QDX models.

A correctly sized discharge hose is important for maintaining the pump's hydraulic performance. An excessively small hose can create high friction losses and reduce the actual flow rate.

The 40 mm outlet is particularly useful for:

  • Rapid drainage
  • Construction dewatering
  • Pond emptying
  • Agricultural irrigation
  • Water tank transfer
  • General high-volume water removal

Cast-Iron Pump Body

The QDX-LA series uses a cast-iron pump body, with technical documentation identifying HT200 as the pump-body material.

The cast-iron construction provides:

  • Good mechanical strength
  • Durable hydraulic housing
  • Resistance to mechanical impact
  • Stable support for internal components
  • Long service life under normal drainage conditions

The pump body is designed for the wet operating environment associated with submersible applications.

Aluminium Motor Casing

The QDX-LA construction uses an aluminium motor casing.

Aluminium provides a practical combination of low weight, corrosion resistance and heat dissipation.

This is useful for portable drainage equipment where the pump may need to be moved between different locations.

Stainless-Steel Shaft

The pump incorporates a stainless-steel shaft.

The shaft is continuously exposed to the wet pump environment, making corrosion resistance an important consideration.

The stainless-steel shaft provides:

  • Corrosion resistance
  • Good mechanical strength
  • Reliable rotation
  • Improved durability
  • Suitability for submerged operation

Double-End Mechanical Seal

The QDX-LA series incorporates a double-end mechanical seal.

The mechanical seal helps isolate the motor from the pumped liquid around the rotating shaft.

This is particularly important in a submersible pump because the hydraulic and motor assemblies operate within a submerged environment.

A properly maintained mechanical seal helps protect the motor against water ingress.

Engineering-Plastic Impeller

Technical documentation for the QDX 10-10-0.55LA identifies an engineering-plastic/PPO impeller.

The engineering-plastic impeller provides a relatively lightweight rotating assembly and is designed for the hydraulic requirements of this pump.

The impeller should not be exposed to large stones, metal debris, ropes, rags or other oversized material.

Copper Motor Winding

The motor uses copper winding, providing good electrical conductivity and suitable thermal characteristics for the 0.55 kW motor.

Copper winding supports efficient motor operation when the pump is operated within its specified electrical and hydraulic conditions.

Built-In Thermal Protector

The QDX-LA series features a built-in thermal protector.

The thermal protection helps protect the motor from excessive temperature caused by abnormal operating conditions such as overload.

External electrical protection is still required. The installation should include appropriate circuit protection, grounding and correctly sized wiring.

Class F Insulation

The motor is specified with Class F insulation.

Class F insulation provides suitable thermal resistance for the motor winding system and supports reliable operation within the manufacturer's specified conditions.

IP68 Protection

The pump is specified with IP68 protection, making it suitable for submerged operation.

The IP68 design is appropriate for applications such as:

  • Wells
  • Drainage pits
  • Water tanks
  • Construction excavations
  • Ponds
  • Agricultural drainage
  • Flooded areas

The IP68 rating should be considered together with the manufacturer's specified 5 m maximum immersion depth.

Maximum Immersion Depth – 5 m

The maximum immersion depth is 5 metres.

The pump should be positioned securely and should never be lifted or suspended by its electrical cable.

For drainage applications, it is advisable to position the pump away from heavy sediment accumulation where possible. Excessive abrasive material can increase wear on the mechanical seal and hydraulic components.

Maximum Liquid Temperature – 40°C

The maximum liquid temperature is 40°C.

The pump is therefore intended primarily for normal-temperature water and lightly contaminated drainage liquids.

Suitable liquids include:

  • Fresh water
  • Rainwater
  • Irrigation water
  • Well water
  • Pond water
  • Lightly contaminated drainage water

High-temperature industrial liquids should not be pumped unless specifically approved by LEO.

Liquid pH and Sand Content

The QDX-LA series is designed for liquids with a pH of approximately 6.5–8 and maximum sand content of approximately 0.1%.

These limitations help reduce corrosion and abrasive wear of the mechanical seal, impeller and other hydraulic components.

Suspended Solids

LEO specifies a suspended-solid passage of up to approximately 0.2 mm and maximum sand content of 0.1% for the QDX-LA series.

This specification is important when selecting the pump for sewage-related applications.

The QDX 10-10-0.55LA should be considered a drainage/water-transfer pump, rather than a heavy-duty raw-sewage pump.

It is not intended for large:

  • Rags
  • Rope
  • Plastic waste
  • Fibrous material
  • Stones
  • Construction debris
  • Thick sludge
  • Large organic solids

For these applications, a dedicated sewage pump with an appropriate solids passage should be used.

Sewage / Wastewater Application

For a website catalogue, the QDX 10-10-0.55LA can be listed within a broad Sewage Submersible Pumps category if that matches your product structure. However, the technically accurate product description is Submersible Drainage Pump.

The pump is suitable for lightly contaminated wastewater and drainage, provided the liquid remains within the specified temperature, pH, sand and solids limits.

It is not a cutter pump and does not have the large solids-handling capability normally associated with dedicated municipal sewage pumps.

Suitable Applications

LEO specifies the QDX-LA series for small electrical irrigation and drainage equipment, rural well-water pumping, farming irrigation and drainage, industrial/construction accumulated-water drainage and aquaculture.

Agricultural applications

  • Farm irrigation
  • Agricultural drainage
  • Rural well-water transfer
  • Garden irrigation
  • Water transfer for farming

Construction applications

  • Excavation dewatering
  • Foundation drainage
  • Construction-site drainage
  • Temporary dewatering
  • Removal of accumulated water

Residential applications

  • Pond drainage
  • Water tank emptying
  • Basement drainage
  • Garden irrigation
  • General water transfer

Industrial applications

  • Industrial accumulated-water drainage
  • Equipment-area drainage
  • Utility water transfer
  • General non-aggressive liquid transfer

Aquaculture

  • Fish pond drainage
  • Tank water transfer
  • Pond emptying
  • Aquaculture water management

Typical Installation

A typical installation can be arranged as:

Drainage pit / pond / well → QDX 10-10-0.55LA → 1½" discharge hose/pipe → drainage point / tank / irrigation system

The pump is submerged directly into the water source, with the discharge line connected to the 40 mm outlet.

For permanent installations, the discharge pipe should be adequately supported so that its weight does not place excessive stress on the pump outlet.

For portable drainage applications, the pump can be moved between different water sources as required.

Pump Positioning and Operation

For reliable operation:

  • Keep the pump sufficiently submerged.
  • Do not exceed the 5 m maximum immersion depth.
  • Place the pump on a stable surface.
  • Keep the pump inlet free from excessive debris.
  • Avoid heavy sediment deposits.
  • Do not lift the pump using the electrical cable.
  • Protect the cable from abrasion and mechanical damage.
  • Use an appropriately sized discharge hose.
  • Avoid excessive bends and restrictions in the discharge line.
  • Ensure the electrical installation is properly grounded.

Main Product Advantages

  1. 0.55 kW / 0.73 HP motor.
  2. 220 V / 50 Hz single-phase operation.
  3. Up to approximately 275 L/min flow.
  4. Up to approximately 16.5 m³/h water transfer.
  5. Approximately 15.2–15.3 m maximum head.
  6. Approximately 10 m rated head.
  7. 1½-inch / 40 mm discharge outlet.
  8. Durable HT200 cast-iron pump body.
  9. Aluminium motor casing.
  10. Stainless-steel shaft.
  11. Double-end mechanical seal.
  12. Engineering-plastic/PPO impeller.
  13. Copper motor winding.
  14. Built-in thermal protection.
  15. Class F insulation.
  16. IP68 protection.
  17. Maximum immersion depth of 5 m.
  18. Maximum liquid temperature of 40°C.
  19. Suitable for irrigation, drainage, construction and aquaculture.
  20. High-flow design suitable for rapid water removal.

Product Details Summary

The LEO QDX 10-10-0.55LA is a 0.55 kW / 0.73 HP single-phase submersible drainage pump designed for agricultural irrigation, drainage, rural well-water pumping, construction dewatering, pond drainage, aquaculture and general water transfer. Operating at 220 V / 50 Hz, it features a 1½-inch / 40 mm discharge outlet, a published maximum flow of approximately 275 L/min (16.5 m³/h) and approximately 15.2–15.3 m maximum head, with a rated head of approximately 10 m.

The pump features a cast-iron HT200 body, aluminium motor casing, stainless-steel shaft, engineering-plastic/PPO impeller and double-end mechanical seal, together with copper motor winding, built-in thermal protection, Class F insulation and IP68 protection. It can operate submerged to a maximum depth of 5 metres and pump liquids up to 40°C, within a pH range of 6.5–8.

For product classification, it is more accurately described as a submersible drainage pump rather than a heavy-duty raw-sewage pump. The QDX-LA specification allows suspended solids only up to approximately 0.2 mm, making the pump appropriate for clean or lightly contaminated drainage water rather than liquids containing large solids, rags or fibrous waste.

SEO Product Title

LEO QDX 10-10-0.55LA Submersible Drainage Pump 0.73HP 0.55kW – 15.3M Head

SEO Product Description

LEO QDX 10-10-0.55LA Submersible Drainage Pump is a reliable 0.73HP / 0.55kW, 220V single-phase submersible pump designed for agricultural irrigation, drainage, rural well-water pumping, construction dewatering, pond drainage, aquaculture and general water-transfer applications. Equipped with a 1½-inch / 40mm discharge outlet, the pump provides up to approximately 275L/min (16.5m³/h) flow and approximately 15.2–15.3 metres maximum head, with a rated head of around 10 metres. The pump features a durable HT200 cast-iron body, aluminium motor casing, stainless-steel shaft, engineering-plastic/PPO impeller and double-end mechanical seal, together with copper motor winding, built-in thermal protection, Class F insulation and IP68 protection. With a maximum immersion depth of 5 metres and maximum liquid temperature of 40°C, the LEO QDX 10-10-0.55LA is an effective solution for drainage, irrigation, water tanks, wells, construction sites, ponds and aquaculture.



 Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - QDX 10-10-0.55LA