B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO SEWAGE SUBMERSIBLE PUMPS - 50 WQ 25-13-2.2 T/QG



The LEO 50 WQ 25-13-2.2 T/QG is a heavy-duty submersible sewage pump with a cutting mechanism, designed for pumping wastewater containing suspended solids, fibrous materials and other sewage contaminants. It is particularly suitable for industrial wastewater drainage, construction sites, commercial facilities, municipal sewage systems, residential drainage stations, agricultural wastewater and manure/silage liquids. The integrated cutter mechanism cuts long fibres and solid contaminants before they enter the hydraulic passage, helping reduce clogging and allowing wastewater to be transported through relatively small-diameter discharge pipework.

The model operates with a 2.2 kW / 3 HP three-phase motor at 380/415 V, 50 Hz, has a 2-inch / 50 mm discharge, a nominal flow of 25 m³/h, nominal head of 13 m, maximum flow of approximately 37 m³/h, and maximum head of approximately 20 m. LEO documentation and Malaysian distributor data identify a motor speed of 3,000 rpm.

Product Specifications

Specification Details
Brand LEO
Model 50 WQ 25-13-2.2 T/QG
Series WQ-T/QG
Pump Type Submersible Sewage Pump with Cutter
Application Wastewater / Sewage / Drainage
Motor Power 2.2 kW
Motor Rating 3 HP
Voltage 380–415 V
Phase Three Phase
Frequency 50 Hz
Motor Speed 3,000 rpm
Nominal Flow 25 m³/h
Maximum Flow Approx. 37 m³/h
Nominal Head 13 m
Maximum Head Approx. 20 m
Discharge Outlet 50 mm / 2"
Cutter Yes
Cutter Type High-speed cutting mechanism
Maximum Liquid Temperature 40°C
Maximum Immersion Depth Up to 5 m in LEO model documentation; some distributor specifications state up to 10 m depending on version/documentation
Motor Winding Copper
Insulation Class F
Protection Class IP68
Mechanical Seal Double Mechanical Seal
Leak Protection Leak-proof detector
Oil Chamber Yes
Float Switch No
Installation Submersible
Net Weight Approx. 29.3 kg
Gross Weight Approx. 35.3 kg
Packing Dimensions Approx. 604 × 269 × 244 mm

LEO commercial documentation lists the 50WQ25-13-2.2T/QG at 380 V, 3,000 rpm, 37 m³/h maximum flow, 20 m maximum head, 2.2 kW / 3 HP and 2-inch outlet, with approximately 29.3 kg net weight.

2.2 kW / 3 HP Three-Phase Motor

The pump is equipped with a 2.2 kW / 3 HP three-phase motor. The standard electrical specification is 380 V / 50 Hz, while Malaysian product listings commonly identify the operating supply as 415 V / 50 Hz.

The three-phase motor is appropriate for continuous-duty commercial and industrial applications where a higher-capacity electrical supply is available.

Compared with small single-phase drainage pumps, the 3 HP motor provides substantially greater hydraulic capacity and is better suited to:

  • Industrial wastewater drainage
  • Construction-site dewatering
  • Commercial sewage systems
  • Municipal drainage
  • Residential sewage stations
  • Agricultural wastewater
  • Manure and silage liquid transfer

25 m³/h Nominal Flow

The 25 in the model designation represents the pump's nominal flow class of approximately 25 m³/h.

This is equivalent to approximately:

25 m³/h = 416.7 L/min

A Malaysian distributor lists the maximum flow at approximately 616.7 L/min / 37 m³/h, while another LEO specification lists the same model at 37 m³/h maximum flow.

The actual flow delivered during operation depends on the total dynamic head, pipework, fittings and system resistance.

13 m Nominal Head

The model is rated at approximately 13 m nominal head.

The complete hydraulic performance extends to approximately 20 m maximum head, depending on the operating point. LEO commercial specifications list 20 m maximum head for this model.

This means the pump is designed to provide a balance between:

High wastewater flow + moderate discharge pressure

rather than being a very-high-head sewage pump.

The actual operating point should always be selected from the pump performance curve based on the system's total dynamic head.

Cutting Mechanism – T/QG Design

One of the main features of the 50 WQ 25-13-2.2 T/QG is its integrated cutting mechanism.

The QG designation identifies the cutting configuration, while the T version belongs to the WQ-T sewage pump range. The cutting mechanism is designed to process fibrous and solid contaminants in wastewater before they can cause blockage in the pump.

The cutter is particularly useful when pumping wastewater containing:

  • Long fibres
  • Textile waste
  • Organic matter
  • Sewage solids
  • Manure
  • Silage liquid
  • Fibrous contaminants

A LEO product description specifically identifies the pump as being equipped with a high-speed stainless-steel cutting knife designed to cut long fibres and solid particles contained in wastewater.

2-Inch / 50 mm Discharge

The pump has a 50 mm / 2-inch discharge connection.

The relatively small discharge diameter is particularly useful when wastewater needs to be transported through smaller pipework.

The cutter helps make this configuration practical by reducing larger fibrous or solid contaminants before they pass through the discharge system.

Typical installations include:

Sewage pit → LEO 50 WQ 25-13-2.2 T/QG → 2" discharge pipeline → sewage treatment / collection point

Sewage and Wastewater Handling

Unlike the QDX drainage pumps, this WQ-T/QG model is specifically designed for sewage and wastewater containing solids.

Applications include:

  • Factory wastewater
  • Commercial wastewater
  • Construction-site sewage
  • Residential sewage
  • Municipal wastewater
  • Drainage stations
  • Agricultural wastewater
  • Manure liquids
  • Silage liquids

LEO's WQ-QG documentation identifies the range for wastewater containing mechanical impurities and applications including sewage treatment plants, residential drainage stations, municipal projects and agricultural use.

Stainless-Steel Cutter

The cutting assembly uses a high-strength cutting mechanism, with product documentation identifying a stainless-steel cutting knife.

Its function is to:

  1. Break down long fibrous material.
  2. Cut larger soft solids.
  3. Reduce the likelihood of impeller blockage.
  4. Improve wastewater passage through the pump.
  5. Allow sewage to be transferred through comparatively small pipework.

This makes the pump particularly useful where ordinary non-clog drainage pumps may experience problems with fibrous material.

Copper Motor Winding

The motor uses copper winding, providing good electrical conductivity and thermal characteristics. LEO's WQ product specifications identify copper winding for the motor.

Copper windings are appropriate for the high-load requirements of a 2.2 kW industrial submersible motor.

Class F Insulation

The motor is specified with Class F insulation.

This provides the winding system with suitable thermal resistance for the intended operating conditions and contributes to reliable operation during extended pumping cycles.

IP68 Protection

The motor enclosure is rated IP68, making the pump suitable for submerged operation.

IP68 protection is important for sewage pumps because the entire motor assembly operates in a wet environment.

The pump is therefore suitable for:

  • Sewage pits
  • Wastewater tanks
  • Drainage stations
  • Treatment plants
  • Construction pits
  • Industrial wastewater collection tanks

Double Mechanical Seal

The pump incorporates a double mechanical seal to protect the motor from wastewater entering through the shaft area.

This is particularly important in sewage applications because the pumped medium can contain suspended solids and contaminants.

The double-seal arrangement provides an additional sealing barrier between the hydraulic chamber and motor section.

Oil Chamber

The WQ-T/QG design incorporates an oil chamber between the pump and motor assemblies. The oil chamber assists mechanical-seal lubrication and provides additional protection for the motor assembly.

The design is intended to improve reliability in demanding submerged wastewater applications.

Leak Detection

The pump is equipped with a leak-proof detector.

The leak-detection system is intended to identify water ingress associated with seal failure and can be integrated with suitable protection/control equipment.

For industrial installations, an appropriate control panel should be used to provide comprehensive protection against:

  • Leakage
  • Overload
  • Overheating
  • Phase failure
  • Short circuit
  • Abnormal operating conditions

No Automatic Float Switch

Unlike the automatic QDX-A models, the 50WQ25-13-2.2T/QG is not supplied with an automatic float switch according to the available product specification.

Automatic water-level control can instead be achieved through an appropriate external control panel and level sensor/float arrangement.

This is more suitable for commercial and industrial sewage installations where the pump is normally integrated into a complete wastewater control system.

Maximum Liquid Temperature

The maximum specified liquid temperature is 40°C.

The pump is therefore designed for normal-temperature wastewater and sewage.

It should not be used for hot process liquids above the specified temperature without manufacturer approval.

Liquid Compatibility

The available LEO product information gives a pH range of approximately 4–10 for the WQ-T/QG configuration.

This gives the pump a wider chemical operating range than the QDX-LA drainage series.

However, it should not be considered a chemical-resistant pump. Strongly corrosive, abrasive, flammable or explosive liquids should not be pumped unless the exact pump configuration has been specifically approved for that medium.

Maximum Immersion Depth

There is some variation between published documentation regarding immersion depth.

The LEO model-specific documentation available for the 50WQ25-13-2.2T/QG specifies a maximum immersion depth of 5 m, while some WQ-series distributor documentation states up to 25 m for the broader WQ family and another product listing gives 10 m for this model.

For a product catalogue, the safest approach is to use the model-specific LEO documentation and verify the supplied unit's nameplate/manual before installation.

Solid and Fibrous Waste

The principal advantage of the T/QG configuration is its ability to handle wastewater containing mechanical contaminants through the cutting mechanism.

However, the cutter does not mean the pump can safely process every type of waste.

Do not intentionally pump:

  • Metal objects
  • Stones
  • Glass
  • Large rigid objects
  • Highly abrasive mineral slurry
  • Explosive liquids
  • Flammable liquids
  • Strongly corrosive chemicals

The pump is intended for sewage and contaminated wastewater, not general industrial waste of unknown composition.

Suitable Applications

LEO's WQ-T/QG range is intended for wastewater drainage in factories, construction sites and commercial facilities, municipal sewage treatment drainage systems, residential drainage stations, municipal projects and agricultural wastewater applications.

Industrial

  • Factory wastewater
  • Industrial sewage
  • Process-area drainage
  • Wastewater collection tanks
  • Commercial wastewater

Construction

  • Construction-site sewage
  • Excavation drainage
  • Temporary wastewater removal
  • Site drainage stations

Municipal

  • Sewage treatment plants
  • Municipal drainage systems
  • Sewage collection stations
  • Residential sewage stations

Agricultural

  • Manure liquid
  • Silage liquid
  • Farm wastewater
  • Agricultural drainage
  • Wastewater transfer

Commercial

  • Shopping facilities
  • Commercial buildings
  • Restaurants and food-service wastewater systems
  • Facility drainage stations

Construction and Build

The pump uses a robust submersible construction intended for demanding wastewater environments.

Key components include:

  • Cast-iron pump housing
  • Copper-wound motor
  • Cutting mechanism
  • Double mechanical seal
  • Oil chamber
  • Leak detector
  • IP68 motor enclosure

The available LEO documentation gives approximately 29.3 kg net weight and 604 × 269 × 244 mm packing dimensions for this model.

Typical Installation

A typical fixed installation can be arranged as:

Sewage Collection Pit → LEO 50 WQ 25-13-2.2 T/QG → 2" Discharge Pipeline → Treatment Plant / Collection Tank

For a professional sewage installation, the pump should be connected to an appropriately sized control panel with suitable overload, short-circuit, phase and leakage protection.

The pump should be installed so that:

  • The cutter inlet remains unobstructed.
  • The pump cannot rotate or move excessively.
  • The discharge pipe is properly supported.
  • The power cable is protected from mechanical damage.
  • The pump remains sufficiently submerged.
  • Access is provided for maintenance and cleaning.

Installation Recommendations

For reliable operation:

  • Use the correct 380/415 V three-phase supply.
  • Confirm the motor rotation before final installation.
  • Use an appropriate motor protection/control panel.
  • Provide proper grounding.
  • Do not lift the pump by the electrical cable.
  • Use suitable lifting equipment.
  • Ensure the cutting inlet is not obstructed.
  • Use correctly sized 2-inch discharge pipework.
  • Avoid excessive pipe bends and restrictions.
  • Do not exceed the manufacturer's immersion-depth specification.
  • Keep the liquid temperature within 40°C.
  • Inspect the cutter periodically.
  • Inspect mechanical seals and oil chamber during scheduled maintenance.

Key Product Advantages

  1. 2.2 kW / 3 HP heavy-duty motor.
  2. 380/415 V three-phase operation.
  3. Designed specifically for sewage and wastewater.
  4. Integrated cutter mechanism.
  5. Stainless-steel cutting knife.
  6. Approximately 25 m³/h nominal flow.
  7. Up to approximately 37 m³/h maximum flow.
  8. Approximately 13 m nominal head.
  9. Up to approximately 20 m maximum head.
  10. 2-inch / 50 mm discharge.
  11. Copper motor winding.
  12. Class F insulation.
  13. IP68 motor protection.
  14. Double mechanical seal.
  15. Oil chamber.
  16. Leak-proof detector.
  17. Suitable for fibrous and solid-containing wastewater.
  18. Suitable for industrial and municipal sewage.
  19. Suitable for construction and agricultural wastewater.
  20. Compact, heavy-duty submersible design.

Product Details Summary

The LEO 50 WQ 25-13-2.2 T/QG is a 3 HP / 2.2 kW three-phase submersible sewage pump with an integrated cutting mechanism, designed for demanding wastewater applications. It operates at 380/415 V, 50 Hz and 3,000 rpm, with a 2-inch / 50 mm discharge, approximately 25 m³/h nominal flow, 37 m³/h maximum flow, 13 m nominal head and approximately 20 m maximum head.

Its major advantage over conventional drainage pumps is the T/QG cutting configuration, which uses a high-speed cutter to break down long fibres and solid contaminants in wastewater, helping reduce clogging and allowing wastewater to be transferred through relatively small-diameter pipework.

The pump incorporates copper motor winding, Class F insulation, IP68 protection, double mechanical sealing, an oil chamber and leak detection, making it suitable for industrial, municipal, commercial, construction and agricultural wastewater systems.

SEO Product Title

LEO 50 WQ 25-13-2.2 T/QG Submersible Sewage Pump with Cutter 3HP 2.2kW – 20M Head, 2" Outlet

SEO Product Description

LEO 50 WQ 25-13-2.2 T/QG Submersible Sewage Pump with Cutter is a heavy-duty 3HP / 2.2kW, 380/415V three-phase sewage pump designed for wastewater drainage in factories, construction sites, commercial facilities, municipal sewage systems, residential drainage stations and agricultural applications. Featuring an integrated high-speed cutting mechanism, the pump is designed to cut long fibres and solid contaminants in wastewater, helping minimise blockage and allowing sewage to be transferred through a 2-inch / 50mm discharge line. The pump delivers approximately 25m³/h nominal flow, up to 37m³/h maximum flow, 13m nominal head and up to 20m maximum head. It features copper motor winding, Class F insulation, IP68 protection, double mechanical seal, oil chamber and leak detection, providing a robust solution for demanding sewage and wastewater pumping applications.



 Inquiry - LEO SEWAGE SUBMERSIBLE PUMPS - 50 WQ 25-13-2.2 T/QG