B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO POOL & SPA PUMPS - XKP-2204E



The LEO XKP-2204E is a high-capacity 2.2 kW / 3.0 HP self-priming swimming pool and spa circulation pump designed for water circulation and filtration in domestic and commercial-type pool systems. It is the larger model in the XKP series and is intended for applications requiring substantial flow and higher pumping head.

The XKP-2204E operates on 220 V, 50 Hz single phase, with a published flow range of approximately 25–500 L/min and a maximum head of approximately 18 m. It uses 2-inch suction and discharge connections and has a maximum suction height of approximately 3.5 m.

Product Description

The LEO XKP-2204E is a self-priming centrifugal pool pump incorporating a pre-filter/strainer for swimming-pool water circulation. It is designed to circulate pool water through sand filters, cartridge filters and other compatible filtration equipment.

With a 2.2 kW / 3 HP motor, the XKP-2204E provides considerably greater capacity than the XKP-804E and XKP-1604E. Its hydraulic curve reaches approximately 30 m³/h (500 L/min) at the low-head end and approximately 18 m head at zero flow.

LEO's XKP documentation describes the series as suitable for circulation in domestic swimming pools and for slightly dirty water containing suspended solids that can be filtered.

Key Specifications

Specification LEO XKP-2204E
Brand LEO
Model XKP-2204E / XKP2204E
Product Type Pool & Spa Pump
Pump Type Self-Priming Centrifugal Pool Pump
Application Swimming Pool / Spa / Filtration
Motor Power 2.2 kW / 2,200 W / 3.0 HP
Voltage 220 V
Frequency 50 Hz
Phase Single Phase
Flow Range 25–500 L/min
Maximum Flow 500 L/min
Maximum Flow 30 m³/h
Head Range 18–3.6 m
Maximum Head Approx. 18 m
Maximum Suction Height 3.5 m
Inlet 2"
Outlet 2"
Pump Body Engineering Plastic
Impeller Engineering Plastic
Shaft AISI 304 Stainless Steel
Motor Winding Copper / regional specification may vary
Thermal Protection Built-in
Insulation Class F in LEO technical documentation
Protection Class IPX5
Maximum Liquid Temperature 35°C in current Malaysian listings
Maximum Ambient Temperature 40°C
Approx. Weight 16–18 kg, depending on listing/packaging
Typical Application Pool circulation and filtration

Malaysian listings specify 2.2 kW / 3 HP, 220 V, 25–500 L/min, 18–3.6 m head, 3.5 m maximum suction and 2" × 2" connections.

Hydraulic Performance

The published XKP-2204E pump curve provides the following approximate performance:

Flow Approx. Head
0 m³/h / 0 L/min 18.0 m
6 m³/h / 100 L/min 17.3 m
9 m³/h / 150 L/min 16.5 m
12 m³/h / 200 L/min 16.0 m
15 m³/h / 250 L/min 14.8 m
18 m³/h / 300 L/min 13.4 m
21 m³/h / 350 L/min 11.7 m
24 m³/h / 400 L/min 9.5 m
27 m³/h / 450 L/min 6.5 m
30 m³/h / 500 L/min 3.3 m

These values are taken from the published XKP hydraulic performance curve.

This table is important because 500 L/min is not available at 18 m head. At approximately 18 m³/h, for example, the pump curve indicates around 13.4 m head.

For an actual pool installation, the operating point will be determined by the intersection of the pump curve and the system's total dynamic head (TDH).

Maximum Flow

The XKP-2204E has a maximum published flow of:

500 L/min

Equivalent to:

  • 30,000 L/h
  • 30 m³/h

This makes the XKP-2204E suitable for relatively high-flow pool circulation systems.

The actual flow depends on:

  • Filter resistance
  • Suction pipe length
  • Discharge pipe length
  • Pipe diameter
  • Number of elbows
  • Valves
  • Pool elevation
  • Skimmer resistance
  • Return fittings
  • Overall system pressure

Therefore, 30 m³/h should be regarded as the maximum hydraulic capacity rather than the guaranteed operating flow.

Maximum Head

The published maximum head is approximately:

18 m

At zero or near-zero flow, the pump can generate its highest pressure/head. As flow increases, available head decreases according to the pump curve.

This relatively high head makes the XKP-2204E suitable for pool systems with greater hydraulic resistance, provided the filtration system and pipework are correctly sized.

Self-Priming Capability

The XKP-2204E is a self-priming centrifugal pump with a specified maximum suction height of approximately 3.5 m.

This allows surface installation where the pump is positioned above the water level within the manufacturer's permitted suction conditions.

For reliable operation:

  • Use appropriately sized suction piping.
  • Keep suction piping as short as practical.
  • Minimise unnecessary elbows.
  • Ensure all suction joints are airtight.
  • Properly prime the pump.
  • Keep the pre-filter basket clean.
  • Prevent dry running.

Self-priming capability does not compensate for an undersized or poorly sealed suction line.

Integrated Pre-Filter

The XKP-2204E uses a pre-filter/strainer arrangement to help prevent larger debris from reaching the pump's impeller.

This is useful in swimming-pool applications where water may contain:

  • Leaves
  • Insects
  • Hair
  • Small debris
  • Suspended particles

Regular inspection and cleaning of the filter basket is important. A blocked basket increases suction resistance and can reduce flow.

Swimming Pool Filtration

The XKP-2204E is designed to circulate pool water through filtration equipment.

A typical installation is:

Swimming Pool → Skimmer / Main Drain → Pump Pre-Filter → XKP-2204E → Sand/Cartridge Filter → Return Line → Swimming Pool

Because the pump can produce up to approximately 30 m³/h, the connected filter must be appropriately sized for the required operating flow.

A filter that is too small can create excessive pressure loss and restrict pump performance.

Applications

The LEO XKP-2204E can be used for:

  • Swimming pools
  • Domestic swimming pools
  • Larger residential pools
  • Pool filtration systems
  • Spa circulation
  • Jacuzzi circulation
  • Water-treatment systems
  • Landscape fountains
  • Decorative water features
  • Clean-water circulation
  • Other applications requiring high-volume water circulation

LEO's XKP documentation identifies the series for swimming-pool water circulation and filtration and for slightly dirty water containing suspended solids that can be filtered.

Engineering-Plastic Pump Body

The XKP-2204E uses an engineering-plastic pump body.

This construction offers:

  • Corrosion resistance
  • Low susceptibility to external corrosion
  • Reduced weight compared with many cast-metal pool pumps
  • Compatibility with normal treated-pool water
  • Durable hydraulic housing

LEO's technical documentation identifies the pump body as engineering plastic.

AISI 304 Stainless-Steel Shaft

The pump incorporates an AISI 304 stainless-steel shaft, providing corrosion resistance for swimming-pool and clean-water applications.

This is particularly useful in pool equipment where the hydraulic components are repeatedly exposed to treated water.

Motor Construction

The XKP-2204E uses a:

2.2 kW / 3 HP single-phase motor

with built-in thermal protection.

LEO technical documentation specifies Class F insulation and IPX5 enclosure protection for the XKP series.

The motor's built-in thermal protector helps protect against excessive temperature during abnormal operating conditions.

IPX5 Protection

The XKP-2204E is specified with IPX5 protection.

This provides protection against water jets from various directions, which is appropriate for pool-pump equipment installed in damp environments.

The motor should nevertheless be installed in a suitable protected location and must not be submerged.

Operating Temperature

Current Malaysian listings specify a maximum liquid temperature of approximately:

35°C

and maximum ambient temperature of approximately:

40°C.

Some regional XKP documentation gives a wider medium-temperature range of 5–50°C, so the exact temperature specification should be confirmed against the nameplate/manual supplied with the particular unit.

For standard swimming-pool operation, the pump is normally used well within the lower end of these limits.

2-Inch Inlet & Outlet

The XKP-2204E has:

2" × 2" suction and discharge connections

with Malaysian listings also describing the connections as approximately 50 mm.

The 2-inch connection is important because the pump is capable of moving up to 500 L/min.

Using undersized pipework can increase friction losses and significantly reduce actual flow.

High-Capacity Pool Pump

The XKP-2204E is the highest-capacity model in the commonly listed XKP-04 series:

Model Motor Max. Head Max. Flow
XKP-804E 0.8 kW 11 m Approx. 18 m³/h
XKP-904E 0.9 kW 14 m Approx. 21 m³/h
XKP-1104E 1.1 kW 15 m Approx. 21 m³/h
XKP-1604E 1.6 kW 17 m Approx. 27 m³/h
XKP-2204E 2.2 kW 18 m 30 m³/h

The LEO hydraulic performance table confirms the progression from the XKP-804E through the XKP-2204E, with the XKP-2204E reaching approximately 30 m³/h at the low-head end.

XKP-2204E vs XKP-1604E

Feature XKP-2204E XKP-1604E
Motor Power 2.2 kW / 3 HP 1.6 kW / 2.1 HP
Voltage 220 V 220–230 V
Max. Flow 500 L/min 450 L/min
Max. Flow 30 m³/h 27 m³/h
Max. Head 18 m 17 m
Max. Suction 3.5 m 3.5 m
Inlet / Outlet 2" × 2" 2" × 2"
Pump Type Self-priming centrifugal Self-priming centrifugal
Pre-Filter Yes Yes
Shaft AISI 304 SS AISI 304 SS
Thermal Protection Yes Yes
Protection IPX5 IPX5

The XKP-2204E provides the highest flow and head capacity of the two and is appropriate where the filtration system requires greater circulation capacity.

Pool Size Consideration

Some market listings associate the XKP-2204E with pools in the approximate 70–100 m³ range.

This should not be treated as a universal maximum pool volume. Correct pump selection depends on the required pool turnover time, filter capacity, pipework and total dynamic head.

For example, a 70 m³ pool requiring a 6-hour turnover would need approximately:

70 ÷ 6 = 11.7 m³/h

A 100 m³ pool requiring an 8-hour turnover would need:

100 ÷ 8 = 12.5 m³/h

The pump should therefore be selected according to the required flow at the actual system head, rather than simply selecting based on pool volume.

Advantages

  • 2.2 kW / 3.0 HP motor
  • 220 V single-phase operation
  • Maximum flow up to 500 L/min
  • Maximum capacity approximately 30 m³/h
  • Maximum head approximately 18 m
  • 25–500 L/min published flow range
  • 18–3.6 m published head range
  • 3.5 m maximum suction height
  • 2" × 2" inlet/outlet
  • Self-priming centrifugal design
  • Integrated pre-filter
  • Engineering-plastic pump body
  • Engineering-plastic impeller
  • AISI 304 stainless-steel shaft
  • Built-in thermal protection
  • Class F insulation
  • IPX5 protection
  • Suitable for pool filtration
  • Suitable for domestic swimming pools
  • Suitable for spa and jacuzzi circulation
  • Suitable for water-treatment systems
  • Suitable for landscape fountains
  • High-flow capability for demanding circulation systems

Important Selection Note

The LEO XKP-2204E is a high-capacity pool circulation and filtration pump, not a sewage or drainage pump.

Its 500 L/min / 30 m³/h maximum flow occurs at the low-head end of its hydraulic curve. At higher system resistance, the actual flow is considerably lower. For example, the published curve indicates approximately 13.4 m head at 18 m³/h and approximately 6.5 m head at 27 m³/h.

For proper selection, calculate:

  • Static elevation
  • Suction-line friction
  • Discharge-line friction
  • Filter pressure loss
  • Valves
  • Elbows
  • Skimmer resistance
  • Return fittings
  • Total dynamic head

The pump's operating point should then be checked against the hydraulic curve.

The connected filter and pipework must also be capable of handling the intended flow.

Technical Product Data

Brand: LEO
Model: XKP-2204E / XKP2204E
Category: Pool & Spa Pump
Pump Type: Self-Priming Centrifugal Pool Pump with Pre-Filter
Motor Power: 2.2 kW / 2,200 W / 3.0 HP
Voltage: 220 V
Frequency: 50 Hz
Phase: Single Phase
Flow Range: 25–500 L/min
Maximum Flow: 500 L/min
Maximum Flow: 30 m³/h
Head Range: 18–3.6 m
Maximum Head: Approx. 18 m
Maximum Suction: 3.5 m
Inlet: 2"
Outlet: 2"
Pump Body: Engineering Plastic
Impeller: Engineering Plastic
Shaft: AISI 304 Stainless Steel
Thermal Protection: Built-in
Insulation Class: F
Protection Class: IPX5
Maximum Liquid Temperature: 35°C in current Malaysian listing
Maximum Ambient Temperature: ≤40°C
Approx. Weight: 16–18 kg depending on version/packaging
Applications: Swimming pools, pool filtration, spas, water-treatment systems, landscape fountains and clean-water circulation.



 Inquiry - LEO POOL & SPA PUMPS - XKP-2204E