The LEO XKP-2204E is a high-capacity 2.2 kW / 3.0 HP self-priming swimming pool and spa circulation pump designed for water circulation and filtration in domestic and commercial-type pool systems. It is the larger model in the XKP series and is intended for applications requiring substantial flow and higher pumping head.
The XKP-2204E operates on 220 V, 50 Hz single phase, with a published flow range of approximately 25–500 L/min and a maximum head of approximately 18 m. It uses 2-inch suction and discharge connections and has a maximum suction height of approximately 3.5 m.
Product Description
The LEO XKP-2204E is a self-priming centrifugal pool pump incorporating a pre-filter/strainer for swimming-pool water circulation. It is designed to circulate pool water through sand filters, cartridge filters and other compatible filtration equipment.
With a 2.2 kW / 3 HP motor, the XKP-2204E provides considerably greater capacity than the XKP-804E and XKP-1604E. Its hydraulic curve reaches approximately 30 m³/h (500 L/min) at the low-head end and approximately 18 m head at zero flow.
LEO's XKP documentation describes the series as suitable for circulation in domestic swimming pools and for slightly dirty water containing suspended solids that can be filtered.
Key Specifications
| Specification | LEO XKP-2204E |
|---|---|
| Brand | LEO |
| Model | XKP-2204E / XKP2204E |
| Product Type | Pool & Spa Pump |
| Pump Type | Self-Priming Centrifugal Pool Pump |
| Application | Swimming Pool / Spa / Filtration |
| Motor Power | 2.2 kW / 2,200 W / 3.0 HP |
| Voltage | 220 V |
| Frequency | 50 Hz |
| Phase | Single Phase |
| Flow Range | 25–500 L/min |
| Maximum Flow | 500 L/min |
| Maximum Flow | 30 m³/h |
| Head Range | 18–3.6 m |
| Maximum Head | Approx. 18 m |
| Maximum Suction Height | 3.5 m |
| Inlet | 2" |
| Outlet | 2" |
| Pump Body | Engineering Plastic |
| Impeller | Engineering Plastic |
| Shaft | AISI 304 Stainless Steel |
| Motor Winding | Copper / regional specification may vary |
| Thermal Protection | Built-in |
| Insulation Class | F in LEO technical documentation |
| Protection Class | IPX5 |
| Maximum Liquid Temperature | 35°C in current Malaysian listings |
| Maximum Ambient Temperature | 40°C |
| Approx. Weight | 16–18 kg, depending on listing/packaging |
| Typical Application | Pool circulation and filtration |
Malaysian listings specify 2.2 kW / 3 HP, 220 V, 25–500 L/min, 18–3.6 m head, 3.5 m maximum suction and 2" × 2" connections.
Hydraulic Performance
The published XKP-2204E pump curve provides the following approximate performance:
| Flow | Approx. Head |
|---|---|
| 0 m³/h / 0 L/min | 18.0 m |
| 6 m³/h / 100 L/min | 17.3 m |
| 9 m³/h / 150 L/min | 16.5 m |
| 12 m³/h / 200 L/min | 16.0 m |
| 15 m³/h / 250 L/min | 14.8 m |
| 18 m³/h / 300 L/min | 13.4 m |
| 21 m³/h / 350 L/min | 11.7 m |
| 24 m³/h / 400 L/min | 9.5 m |
| 27 m³/h / 450 L/min | 6.5 m |
| 30 m³/h / 500 L/min | 3.3 m |
These values are taken from the published XKP hydraulic performance curve.
This table is important because 500 L/min is not available at 18 m head. At approximately 18 m³/h, for example, the pump curve indicates around 13.4 m head.
For an actual pool installation, the operating point will be determined by the intersection of the pump curve and the system's total dynamic head (TDH).
Maximum Flow
The XKP-2204E has a maximum published flow of:
500 L/min
Equivalent to:
- 30,000 L/h
- 30 m³/h
This makes the XKP-2204E suitable for relatively high-flow pool circulation systems.
The actual flow depends on:
- Filter resistance
- Suction pipe length
- Discharge pipe length
- Pipe diameter
- Number of elbows
- Valves
- Pool elevation
- Skimmer resistance
- Return fittings
- Overall system pressure
Therefore, 30 m³/h should be regarded as the maximum hydraulic capacity rather than the guaranteed operating flow.
Maximum Head
The published maximum head is approximately:
18 m
At zero or near-zero flow, the pump can generate its highest pressure/head. As flow increases, available head decreases according to the pump curve.
This relatively high head makes the XKP-2204E suitable for pool systems with greater hydraulic resistance, provided the filtration system and pipework are correctly sized.
Self-Priming Capability
The XKP-2204E is a self-priming centrifugal pump with a specified maximum suction height of approximately 3.5 m.
This allows surface installation where the pump is positioned above the water level within the manufacturer's permitted suction conditions.
For reliable operation:
- Use appropriately sized suction piping.
- Keep suction piping as short as practical.
- Minimise unnecessary elbows.
- Ensure all suction joints are airtight.
- Properly prime the pump.
- Keep the pre-filter basket clean.
- Prevent dry running.
Self-priming capability does not compensate for an undersized or poorly sealed suction line.
Integrated Pre-Filter
The XKP-2204E uses a pre-filter/strainer arrangement to help prevent larger debris from reaching the pump's impeller.
This is useful in swimming-pool applications where water may contain:
- Leaves
- Insects
- Hair
- Small debris
- Suspended particles
Regular inspection and cleaning of the filter basket is important. A blocked basket increases suction resistance and can reduce flow.
Swimming Pool Filtration
The XKP-2204E is designed to circulate pool water through filtration equipment.
A typical installation is:
Swimming Pool → Skimmer / Main Drain → Pump Pre-Filter → XKP-2204E → Sand/Cartridge Filter → Return Line → Swimming Pool
Because the pump can produce up to approximately 30 m³/h, the connected filter must be appropriately sized for the required operating flow.
A filter that is too small can create excessive pressure loss and restrict pump performance.
Applications
The LEO XKP-2204E can be used for:
- Swimming pools
- Domestic swimming pools
- Larger residential pools
- Pool filtration systems
- Spa circulation
- Jacuzzi circulation
- Water-treatment systems
- Landscape fountains
- Decorative water features
- Clean-water circulation
- Other applications requiring high-volume water circulation
LEO's XKP documentation identifies the series for swimming-pool water circulation and filtration and for slightly dirty water containing suspended solids that can be filtered.
Engineering-Plastic Pump Body
The XKP-2204E uses an engineering-plastic pump body.
This construction offers:
- Corrosion resistance
- Low susceptibility to external corrosion
- Reduced weight compared with many cast-metal pool pumps
- Compatibility with normal treated-pool water
- Durable hydraulic housing
LEO's technical documentation identifies the pump body as engineering plastic.
AISI 304 Stainless-Steel Shaft
The pump incorporates an AISI 304 stainless-steel shaft, providing corrosion resistance for swimming-pool and clean-water applications.
This is particularly useful in pool equipment where the hydraulic components are repeatedly exposed to treated water.
Motor Construction
The XKP-2204E uses a:
2.2 kW / 3 HP single-phase motor
with built-in thermal protection.
LEO technical documentation specifies Class F insulation and IPX5 enclosure protection for the XKP series.
The motor's built-in thermal protector helps protect against excessive temperature during abnormal operating conditions.
IPX5 Protection
The XKP-2204E is specified with IPX5 protection.
This provides protection against water jets from various directions, which is appropriate for pool-pump equipment installed in damp environments.
The motor should nevertheless be installed in a suitable protected location and must not be submerged.
Operating Temperature
Current Malaysian listings specify a maximum liquid temperature of approximately:
35°C
and maximum ambient temperature of approximately:
40°C.
Some regional XKP documentation gives a wider medium-temperature range of 5–50°C, so the exact temperature specification should be confirmed against the nameplate/manual supplied with the particular unit.
For standard swimming-pool operation, the pump is normally used well within the lower end of these limits.
2-Inch Inlet & Outlet
The XKP-2204E has:
2" × 2" suction and discharge connections
with Malaysian listings also describing the connections as approximately 50 mm.
The 2-inch connection is important because the pump is capable of moving up to 500 L/min.
Using undersized pipework can increase friction losses and significantly reduce actual flow.
High-Capacity Pool Pump
The XKP-2204E is the highest-capacity model in the commonly listed XKP-04 series:
| Model | Motor | Max. Head | Max. Flow |
|---|---|---|---|
| XKP-804E | 0.8 kW | 11 m | Approx. 18 m³/h |
| XKP-904E | 0.9 kW | 14 m | Approx. 21 m³/h |
| XKP-1104E | 1.1 kW | 15 m | Approx. 21 m³/h |
| XKP-1604E | 1.6 kW | 17 m | Approx. 27 m³/h |
| XKP-2204E | 2.2 kW | 18 m | 30 m³/h |
The LEO hydraulic performance table confirms the progression from the XKP-804E through the XKP-2204E, with the XKP-2204E reaching approximately 30 m³/h at the low-head end.
XKP-2204E vs XKP-1604E
| Feature | XKP-2204E | XKP-1604E |
|---|---|---|
| Motor Power | 2.2 kW / 3 HP | 1.6 kW / 2.1 HP |
| Voltage | 220 V | 220–230 V |
| Max. Flow | 500 L/min | 450 L/min |
| Max. Flow | 30 m³/h | 27 m³/h |
| Max. Head | 18 m | 17 m |
| Max. Suction | 3.5 m | 3.5 m |
| Inlet / Outlet | 2" × 2" | 2" × 2" |
| Pump Type | Self-priming centrifugal | Self-priming centrifugal |
| Pre-Filter | Yes | Yes |
| Shaft | AISI 304 SS | AISI 304 SS |
| Thermal Protection | Yes | Yes |
| Protection | IPX5 | IPX5 |
The XKP-2204E provides the highest flow and head capacity of the two and is appropriate where the filtration system requires greater circulation capacity.
Pool Size Consideration
Some market listings associate the XKP-2204E with pools in the approximate 70–100 m³ range.
This should not be treated as a universal maximum pool volume. Correct pump selection depends on the required pool turnover time, filter capacity, pipework and total dynamic head.
For example, a 70 m³ pool requiring a 6-hour turnover would need approximately:
70 ÷ 6 = 11.7 m³/h
A 100 m³ pool requiring an 8-hour turnover would need:
100 ÷ 8 = 12.5 m³/h
The pump should therefore be selected according to the required flow at the actual system head, rather than simply selecting based on pool volume.
Advantages
- 2.2 kW / 3.0 HP motor
- 220 V single-phase operation
- Maximum flow up to 500 L/min
- Maximum capacity approximately 30 m³/h
- Maximum head approximately 18 m
- 25–500 L/min published flow range
- 18–3.6 m published head range
- 3.5 m maximum suction height
- 2" × 2" inlet/outlet
- Self-priming centrifugal design
- Integrated pre-filter
- Engineering-plastic pump body
- Engineering-plastic impeller
- AISI 304 stainless-steel shaft
- Built-in thermal protection
- Class F insulation
- IPX5 protection
- Suitable for pool filtration
- Suitable for domestic swimming pools
- Suitable for spa and jacuzzi circulation
- Suitable for water-treatment systems
- Suitable for landscape fountains
- High-flow capability for demanding circulation systems
Important Selection Note
The LEO XKP-2204E is a high-capacity pool circulation and filtration pump, not a sewage or drainage pump.
Its 500 L/min / 30 m³/h maximum flow occurs at the low-head end of its hydraulic curve. At higher system resistance, the actual flow is considerably lower. For example, the published curve indicates approximately 13.4 m head at 18 m³/h and approximately 6.5 m head at 27 m³/h.
For proper selection, calculate:
- Static elevation
- Suction-line friction
- Discharge-line friction
- Filter pressure loss
- Valves
- Elbows
- Skimmer resistance
- Return fittings
- Total dynamic head
The pump's operating point should then be checked against the hydraulic curve.
The connected filter and pipework must also be capable of handling the intended flow.
Technical Product Data
Brand: LEO
Model: XKP-2204E / XKP2204E
Category: Pool & Spa Pump
Pump Type: Self-Priming Centrifugal Pool Pump with Pre-Filter
Motor Power: 2.2 kW / 2,200 W / 3.0 HP
Voltage: 220 V
Frequency: 50 Hz
Phase: Single Phase
Flow Range: 25–500 L/min
Maximum Flow: 500 L/min
Maximum Flow: 30 m³/h
Head Range: 18–3.6 m
Maximum Head: Approx. 18 m
Maximum Suction: 3.5 m
Inlet: 2"
Outlet: 2"
Pump Body: Engineering Plastic
Impeller: Engineering Plastic
Shaft: AISI 304 Stainless Steel
Thermal Protection: Built-in
Insulation Class: F
Protection Class: IPX5
Maximum Liquid Temperature: 35°C in current Malaysian listing
Maximum Ambient Temperature: ≤40°C
Approx. Weight: 16–18 kg depending on version/packaging
Applications: Swimming pools, pool filtration, spas, water-treatment systems, landscape fountains and clean-water circulation.
Inquiry - LEO POOL & SPA PUMPS - XKP-2204E