B116, C15 Jalan Haji Ahmad, Perkampungan Seri Setali, 25300 Kuantan, Pahang, Malaysia.

+6019-323 7617

kstoolsdepot@gmail.com


Share:


LEO MULTISTAGE CENTRIFUGAL PUMPS - 5ACM-100S



The LEO 5ACm100S is a five-stage stainless-steel horizontal multistage centrifugal pump designed for clean-water transfer, domestic water supply, pressure boosting, high-rise buildings, irrigation, industrial water supply and long-distance water transfer. It uses a 0.9 kW / 1.25 HP single-phase 220V motor, five-stage hydraulic construction and 1" × 1" suction/discharge connections. LEO identifies the ACm-S series for clean water and liquids with physical and chemical properties similar to water, including urban and domestic water supply and high-rise applications.

Product Specifications

Specification 5ACm100S
Brand LEO
Model 5ACm100S / 5ACM-100S
Pump Type Stainless Steel Horizontal Multistage Centrifugal Pump
Series ACm-S
Number of Stages 5
Motor Power 0.9 kW
Motor Rating 1.25 HP
Motor Type Single Phase
Voltage 220V
Frequency 50 Hz
Flow Range 5–100 L/min
Maximum Flow Approx. 6.0 m³/h
Head Range Approx. 55–8 m
Maximum Head Approx. 55 m
Maximum Suction Height 8 m
Suction Connection 1"
Discharge Connection 1"
Inlet / Outlet 1" × 1"
Hydraulic Design 5-Stage
Pump Construction Stainless Steel
Shaft AISI 304 Stainless Steel
Impeller Thermoplastic
Motor Winding Copper
Insulation Class F
Protection Class IPX4
Motor Protection Built-in Thermal Protector
Maximum Ambient Temperature Up to +50°C depending on regional specification
Typical Liquid Temperature Up to +60°C according to Malaysian listings

The Malaysian product specification lists 0.9 kW, 220V, 5–100 L/min flow, 55–8 m head, 8 m maximum suction and 1" × 1" connections.

Five-Stage Multistage Design

The "5" in the 5ACm100S model indicates the pump has five hydraulic stages/impellers.

The stages operate in series. Water passes through each stage sequentially, allowing pressure/head to build progressively. This five-stage configuration provides considerably higher head than the lower-stage 3ACm100S and 4ACm100S models.

The 5ACm100S is therefore suited to applications requiring:

  • Higher water pressure
  • Elevated water transfer
  • Domestic pressure boosting
  • High-rise water supply
  • Long-distance water transfer
  • Irrigation systems
  • Industrial clean-water transfer

LEO's 2026 European product information identifies the stainless-steel multistage range with 4- and 5-stage thermoplastic impeller configurations, with the five-stage model reaching approximately 6 m³/h maximum volume and 55 m maximum height.

Hydraulic Performance

Published Malaysian specifications give the following approximate operating range:

Parameter 5ACm100S
Minimum listed flow 5 L/min
Maximum flow 100 L/min
Maximum flow 6.0 m³/h
Maximum head 55 m
High-flow head Approx. 8 m
Maximum suction 8 m

The 55 m maximum head and 100 L/min maximum flow do not occur at the same operating point. The actual duty point must be determined from the pump curve and system resistance.

Factors affecting actual performance include:

  • Vertical elevation
  • Pipe length
  • Pipe diameter
  • Pipe friction
  • Number of fittings
  • Valves
  • Filters
  • Required outlet pressure
  • Water temperature

The published 5ACm100S specification gives 5–100 L/min flow and 55–8 m head.

0.9 kW / 1.25 HP Motor

The pump is equipped with a 0.9 kW / 1.25 HP single-phase motor operating on 220V.

Main motor characteristics:

  • Power: 0.9 kW
  • Rating: 1.25 HP
  • Voltage: 220V
  • Phase: Single phase
  • Frequency: 50 Hz
  • Copper winding
  • Class F insulation
  • IPX4 protection
  • Built-in thermal protection

The ACm-S series specifies a built-in thermal protector for single-phase motors, Class F insulation and IPX4 enclosure protection.

Stainless-Steel Construction

The 5ACm100S is part of LEO's ACm-S stainless-steel multistage range.

The stainless-steel construction is advantageous for clean-water applications because it provides improved resistance to corrosion compared with conventional cast-iron hydraulic construction.

Typical benefits include:

  • Corrosion resistance
  • Durable wetted components
  • Clean appearance
  • Suitable for domestic water systems
  • Suitable for commercial water transfer
  • Good resistance to normal clean-water service

LEO specifically positions the ACm-S series for industrial use, urban water supply, domestic water supply, high-rise buildings and long-distance water transfer.

AISI 304 Stainless-Steel Shaft

The pump incorporates an AISI 304 stainless-steel shaft.

The shaft is responsible for transmitting motor torque to the five impeller stages. AISI 304 provides good corrosion resistance and mechanical durability for clean-water applications.

Thermoplastic Impellers

The ACm-S series uses thermoplastic impellers.

The five-stage configuration allows multiple impellers to build pressure progressively while keeping the pump relatively compact.

Advantages include:

  • Lightweight hydraulic components
  • Corrosion resistance
  • Compact multistage construction
  • Suitable performance for clean-water applications
  • Reduced hydraulic assembly weight

LEO's 2026 brochure specifically describes the stainless-steel multistage models as using thermoplastic impellers.

1" × 1" Connections

The pump uses:

Suction: 1"
Discharge: 1"

This makes it suitable for many standard domestic and irrigation systems.

For optimum performance:

  • Use correctly sized suction piping.
  • Keep the suction pipe short.
  • Minimize sharp bends.
  • Avoid unnecessary restrictions.
  • Ensure all suction joints are airtight.
  • Support connected pipework independently.

Maximum Suction Height – 8 m

The specified maximum suction height is 8 m.

Actual suction performance depends on:

  • Atmospheric pressure
  • Installation altitude
  • Water temperature
  • Suction pipe diameter
  • Suction pipe length
  • Pipe fittings
  • Water level
  • Air leakage
  • Friction losses

For suction-lift installations, the suction line should be as short, direct and airtight as possible.

Suitable Fluids

The 5ACm100S is intended primarily for clean water and liquids with physical and chemical properties similar to water. LEO specifically identifies clean-water transfer as the intended service.

Suitable fluids/applications include:

  • Clean fresh water
  • Treated water
  • Storage-tank water
  • Clean well water
  • Irrigation water
  • Domestic water
  • General service water

It should not be used for abrasive slurry, heavily contaminated wastewater or aggressive chemicals without confirming material compatibility.

Domestic Water Supply

The five-stage hydraulic design makes the 5ACm100S particularly suitable for domestic systems requiring higher pressure.

Potential applications include:

  • House water supply
  • Water tank transfer
  • Shower pressure boosting
  • Residential booster systems
  • Garden water supply
  • Multiple-outlet distribution
  • Elevated water transfer

Its approximately 55 m maximum head provides considerably more pressure capability than the lower-stage models in the same family.

High-Rise Water Supply

The ACm-S range is specifically identified by LEO for high-rise building water supply.

The multistage configuration helps overcome:

  • Building elevation
  • Pipe friction
  • Pressure losses
  • Long distribution lines
  • Multiple fittings

For high-rise installations, the pump must be selected according to the required duty point, and the system should be checked for minimum and maximum pressure conditions.

Irrigation Applications

The 5ACm100S can be used for clean-water irrigation applications where the required flow and pressure fall within its hydraulic curve.

Suitable applications include:

  • Garden irrigation
  • Lawn sprinklers
  • Nursery irrigation
  • Greenhouse irrigation
  • Small agricultural irrigation
  • Orchard irrigation
  • Tank-to-field transfer

The maximum listed flow is approximately 100 L/min, equivalent to approximately 6.0 m³/h.

The actual flow available at the sprinkler or outlet will depend on system head.

Pressure Boosting

The five-stage arrangement makes this model suitable for pressure-boosting applications.

Common applications include:

  • Domestic pressure boosting
  • Tank outlet boosting
  • Building water boosting
  • Irrigation pressure boosting
  • Long-distance water supply
  • Commercial water distribution

The 5ACm100S should be selected based on required flow rate and total dynamic head rather than maximum head alone.

Long-Distance Water Transfer

The higher head capability is useful where water must be transferred over longer distances.

The pump can provide additional head to overcome:

  • Pipe friction
  • Elevation difference
  • Valves
  • Filters
  • Elbows and fittings
  • Other system resistance

Correct pipe sizing remains important. Undersized pipework can significantly reduce the actual flow delivered by the pump.

Industrial Applications

LEO specifies the ACm-S series for industrial use and urban water supply.

Potential applications include:

  • Process-water transfer
  • Utility-water supply
  • Equipment water supply
  • Tank filling
  • Clean-water circulation
  • Small industrial booster systems
  • General industrial water transfer

For liquids other than clean water, chemical and material compatibility should be verified before operation.

Motor Protection

The ACm-S series provides:

Insulation: Class F
Protection: IPX4
Thermal protection: Built-in for single-phase motors.

The thermal protector helps reduce the risk of motor winding damage caused by overheating.

Proper electrical protection and grounding should still be provided during installation.

Operating Temperature

A Malaysian product listing specifies a maximum water temperature of 60°C for the 5ACm100S.

Because LEO documentation can vary by market and product generation, the nameplate/manual supplied with your exact pump should be treated as the final temperature reference.

For normal website cataloguing, you can state:

Maximum liquid temperature: Up to 60°C — subject to manufacturer specification for supplied unit.

Installation Recommendations

For reliable operation:

  • Install the pump on a firm, level base.
  • Position it close to the water source.
  • Keep the suction line short and direct.
  • Ensure suction connections are airtight.
  • Use suitable 1" suction piping.
  • Install a foot valve/strainer where required.
  • Avoid excessive elbows and restrictions.
  • Support connected pipework independently.
  • Prime the pump before initial operation.
  • Confirm adequate water supply.
  • Provide proper electrical earthing.
  • Install suitable electrical protection.
  • Do not operate the pump dry.
  • Keep operation within the published pump curve.

Maintenance

Recommended maintenance includes:

  • Checking for water leakage
  • Inspecting the mechanical seal
  • Checking suction-line air leakage
  • Cleaning the suction strainer
  • Inspecting impellers
  • Inspecting diffusers
  • Checking abnormal vibration
  • Checking unusual noise
  • Monitoring motor temperature
  • Checking electrical connections
  • Monitoring pressure and flow
  • Inspecting valves and pipework

Regular maintenance helps maintain hydraulic performance and extend mechanical-seal and bearing life.

5ACm100S vs 4ACm100S

Specification 4ACm100S 5ACm100S
Number of Stages 4 5
Motor Power 0.75 kW 0.9 kW
Motor Rating 1 HP 1.25 HP
Voltage 220V 220V
Maximum Flow 90 L/min 100 L/min
Maximum Flow 5.4 m³/h 6.0 m³/h
Maximum Head Approx. 43.5–45 m Approx. 55 m
Maximum Suction 8 m 8 m
Connection 1" × 1" 1" × 1"
Main Advantage Moderate pressure/flow Higher pressure and capacity

The 5ACm100S adds one hydraulic stage and increases motor power to 0.9 kW, giving it higher head and flow capability. LEO's 2026 European brochure lists the five-stage stainless-steel configuration at approximately 6 m³/h maximum volume and 55 m maximum height.

5ACm100S vs 3ACm100S

Specification 3ACm100S 5ACm100S
Number of Stages 3 5
Motor Power 0.6 kW 0.9 kW
Motor Rating 0.8 HP 1.25 HP
Voltage 220V 220V
Maximum Flow Approx. 78–90 L/min* Approx. 100 L/min
Maximum Head Approx. 33.5–35 m* Approx. 55 m
Maximum Suction 8 m 8 m
Connection 1" × 1" 1" × 1"
Main Advantage Lower power Higher pressure/capacity

*Published regional specifications vary slightly for the 3ACm100S.

Key Advantages

Five-Stage Hydraulic Design: Provides high head from a compact horizontal pump.

1.25 HP / 0.9 kW Motor: Suitable for higher-demand water-supply and pressure applications.

Up to 100 L/min Flow: Provides approximately 6.0 m³/h maximum listed capacity.

Up to 55 m Head: Suitable for pressure boosting, elevated water transfer and long pipe runs.

Stainless-Steel Construction: Provides good corrosion resistance for clean-water applications.

AISI 304 Shaft: Provides corrosion resistance and mechanical durability.

Thermoplastic Impellers: Provide a compact and corrosion-resistant multistage hydraulic assembly.

8 m Maximum Suction: Suitable for appropriate suction-lift installations.

220V Single Phase: Suitable for standard single-phase electrical supplies.

1" × 1" Connections: Convenient for domestic and irrigation pipework.

Product Summary

The LEO 5ACm100S is a 1.25 HP / 0.9 kW, 220V single-phase, five-stage stainless-steel horizontal multistage centrifugal pump designed for clean-water transfer, domestic water supply, pressure boosting, high-rise water supply, irrigation, industrial water supply and long-distance water transfer. LEO specifically identifies the ACm-S range for clean-water transfer, urban/domestic water supply, high-rise buildings and long-distance applications.

The commonly published Malaysian specification is approximately 5–100 L/min flow, 55–8 m head, 8 m maximum suction height and 1" × 1" inlet/outlet connections, with a 0.9 kW / 1.25 HP 220V motor.



 Inquiry - LEO MULTISTAGE CENTRIFUGAL PUMPS - 5ACM-100S