The LEO AJM45S is a compact self-priming jet water pump from LEO's AJm-S stainless-steel jet pump range. It is designed for clean-water transfer, shallow-well water lifting, garden irrigation, domestic water supply and pressure boosting.
The pump is powered by a 0.45 kW / 0.6 HP, 220 V single-phase motor and provides approximately 5–40 L/min flow with a 35–16 m head range. It has 1" × 1" inlet and outlet connections and a maximum suction capability of approximately 9 m.
Technical Specifications
| Specification | LEO AJM45S |
|---|---|
| Brand | LEO |
| Series | AJm-S |
| Model | AJM45S |
| Pump Type | Self-Priming Jet Pump |
| Motor Power | 0.45 kW / 0.6 HP |
| Voltage | 220 V |
| Phase | Single Phase |
| Frequency | 50 Hz |
| Flow Range | 5–40 L/min |
| Maximum Flow | 40 L/min |
| Equivalent Maximum Flow | Approx. 2.4 m³/h |
| Head Range | 35–16 m |
| Maximum Head | Approx. 35 m |
| Maximum Suction | 9 m |
| Inlet | 1" |
| Outlet | 1" |
| Impeller | Stainless Steel |
| Pump Body | Stainless Steel for AJm-S configuration |
| Shaft | AISI 304 Stainless Steel |
| Motor Winding | Copper |
| Bearing | C&U |
| Thermal Protection | Built-In |
| Insulation Class | F |
| Protection Class | IPX4 |
| Maximum Liquid Temperature | +40°C to +60°C, depending on regional specification |
| Maximum Ambient Temperature | +40°C |
| Mechanical Seal | Carbon / Ceramic |
| Duty | Continuous |
LEO Europe identifies the AJm45S with a 0.45 kW motor, while the AJm-S construction uses an AISI 304 stainless-steel pump body, stainless-steel impeller and stainless-steel shaft. Malaysian suppliers commonly specify the model at 5–40 L/min, 35–16 m head and 9 m maximum suction.
Pump Performance
The AJM45S provides:
- Flow: 5–40 L/min
- Maximum flow: approximately 40 L/min
- Maximum head: approximately 35 m
- Head operating range: approximately 35–16 m
- Maximum suction: approximately 9 m
- Inlet/outlet: 1" × 1"
The 35 m maximum head and 40 L/min maximum flow are different points on the pump's performance curve; the pump does not deliver 40 L/min at 35 m head.
At higher flow rates, the available head decreases. This is important when selecting the pump according to the actual system duty point.
Self-Priming Jet Pump Design
The AJM45S uses a jet-pump self-priming system, making it suitable for drawing water from sources located below the pump.
Typical sources include:
- Shallow wells
- Underground tanks
- Ground-level storage tanks
- Water reservoirs
- Domestic water sources
The specified maximum suction is approximately 9 m.
Actual suction performance depends on installation conditions. Long suction pipes, excessive bends, undersized piping, high water temperature and air leakage can substantially reduce practical suction performance.
For reliable operation, the suction line should be properly sealed and appropriately sized.
Stainless-Steel Pump Construction
The AJm-S designation is important because the S-series uses a stainless-steel pump body.
LEO Europe lists the AJm45S construction as:
- Pump body: AISI 304 stainless steel
- Pump bottom: AISI 304 stainless steel
- Impeller: AISI 304 stainless steel
- Shaft: stainless steel
- Venturi tube: Noryl/PPO
- Diffuser: Noryl/PPO
- Mechanical seal: carbon/ceramic
- O-ring: NBR
Some Malaysian listings describe the AJM45S simply as a stainless-steel jet pump, while others list the standard AJM-S hydraulic construction separately. For catalogue purposes, the safest description is stainless-steel AJm-S jet pump with stainless-steel impeller and AISI 304 shaft.
Stainless-Steel Impeller
The AJM45S uses a stainless-steel impeller, providing good corrosion resistance and durability for clean-water applications.
This makes the pump suitable for:
- Domestic water supply
- Well-water pumping
- Garden irrigation
- Water transfer
- Pressure boosting
- General clean-water applications
The pump is not designed for significant quantities of abrasive solids, sludge, fibrous material or wastewater.
AISI 304 Shaft
The AISI 304 stainless-steel shaft provides good corrosion resistance and mechanical durability in the rotating assembly.
The combination of a stainless-steel impeller and AISI 304 shaft is particularly appropriate for normal clean-water pumping applications.
Motor Specifications
The AJM45S is equipped with a:
- 0.45 kW / 0.6 HP motor
- 220 V supply
- 50 Hz frequency
- Single-phase configuration
- Copper winding
- C&U bearing
- Built-in thermal protector
- Class F insulation
- IPX4 protection
Malaysian product listings specify the motor as 450 W / 0.6 HP at 220 V.
Motor Protection
The single-phase motor incorporates a built-in thermal protector to help protect the winding against overheating during abnormal operating conditions.
The motor is specified with:
Insulation Class: F
Protection Class: IPX4
Maximum Ambient Temperature: +40°C
These specifications are listed for the AJm-S series by Malaysian suppliers and LEO-related technical documentation.
Pump Connections
The AJM45S uses:
Inlet: 1"
Outlet: 1"
The 1" × 1" configuration makes the pump convenient for common domestic water, irrigation and plumbing installations.
The suction line should be kept as short and direct as practical, with adequate pipe diameter and properly sealed joints.
Mechanical Seal
The pump uses a carbon/ceramic mechanical seal. LEO's AJm-S technical documentation identifies the mechanical seal material as carbon/ceramic.
The mechanical seal helps prevent water leakage along the rotating shaft between the pump hydraulic section and motor assembly.
Pumping Medium
The AJM45S is intended for clean water or liquids with physical and chemical properties similar to water. LEO specifies the AJm-S series for clean-water transfer and related applications.
It should not be selected for:
- Sewage
- Sludge
- Heavy sediment
- Abrasive liquids
- Liquids containing large solids
- Fibrous wastewater
For these applications, a dedicated solids-handling or wastewater pump should be used.
Temperature Specification
There is some variation in published regional specifications.
One Malaysian AJM45S listing specifies maximum liquid temperature of +40°C, while another Malaysian listing gives up to +60°C.
LEO's European AJm45S information lists a maximum liquid temperature of +60°C and maximum ambient temperature of +40°C.
For a product catalogue, the temperature rating should therefore be matched to the exact regional model/nameplate supplied.
Recommended Applications
1. Domestic Water Supply
The AJM45S can be used to provide clean water to residential points where moderate pressure is required.
2. Well-Water Lifting
Its self-priming design and approximately 9 m maximum suction make it suitable for suitable shallow-well applications.
3. Garden Irrigation
Suitable for garden hoses, sprinklers and small irrigation systems.
4. Pressure Boosting
The pump can increase pressure in domestic and light-duty water systems where the required duty point falls within its performance curve.
5. Water Tank Transfer
Suitable for transferring clean water between storage tanks and other water points.
6. General Water Transfer
The compact 0.6 HP configuration makes it suitable for relatively small clean-water transfer duties.
LEO specifically identifies well-water lifting, garden irrigation, running-water pressure boosting and supporting equipment among the intended applications of the AJm-S range.
Main Advantages
The LEO AJM45S provides:
- 0.45 kW / 0.6 HP motor
- Self-priming jet-pump design
- 5–40 L/min flow
- 35–16 m head range
- Approximately 35 m maximum head
- Approximately 9 m maximum suction
- Stainless-steel pump construction
- Stainless-steel impeller
- AISI 304 stainless-steel shaft
- Copper motor winding
- C&U bearing
- Built-in thermal protection
- Class F insulation
- IPX4 protection
- 1" × 1" inlet/outlet
- Carbon/ceramic mechanical seal
- Compact construction
- Suitable for domestic, irrigation, well-water and pressure-boosting applications.
AJm-S Series Comparison
| Model | Motor | Flow Range | Head Range | Max. Suction | Inlet / Outlet |
|---|---|---|---|---|---|
| AJM30S | 0.30 kW | — | — | 9 m | 1" × 1" |
| AJM45S | 0.45 kW / 0.6 HP | 5–40 L/min | 35–16 m | 9 m | 1" × 1" |
| AJM60S | 0.60 kW | — | — | 9 m | 1" × 1" |
| AJM75S | 0.75 kW / 1 HP | 5–55 L/min | 40–20 m | 9 m | 1" × 1" |
| AJM90S | 0.90 kW / 1.2 HP | 5–60 L/min | 44–22 m | 9 m | 1" × 1" |
The AJM45S is the compact 0.6 HP stainless-steel AJm-S model, positioned below the higher-powered AJM75S and AJM90S.
Dimensions & Weight
LEO Europe lists the AJm45S pump dimensions at approximately:
- Length: 337 mm
- Width: 180 mm
- Height: 181.5 mm
Its listed packaging information is approximately:
- Packaging length: 350 mm
- Packaging width: 180 mm
- Packaging height: 220 mm
- Packaging weight: 6.9 kg
Malaysian suppliers list the unit weight at approximately 6–6.2 kg, with some differences depending on whether product or packaging dimensions are being quoted.
Product Description
LEO AJM45S Jet Pump 0.45kW / 0.6HP 220V is a compact stainless-steel self-priming water pump designed for clean-water transfer, well-water lifting, garden irrigation, domestic water supply and pressure boosting. Powered by a 0.45 kW / 0.6 HP single-phase motor, the AJM45S provides approximately 5–40 L/min flow with a 35–16 m head range, making it suitable for small to medium clean-water pumping applications.
The pump features a stainless-steel pump body, stainless-steel impeller and AISI 304 shaft, together with copper motor winding, C&U bearing, built-in thermal protection, Class F insulation and IPX4 protection. Its self-priming jet design provides approximately 9 m maximum suction capability, subject to actual installation conditions.
With 1" × 1" inlet and outlet connections, the LEO AJM45S is suitable for shallow-well water lifting, garden irrigation, domestic water supply, water tank transfer and pressure boosting where a compact and reliable self-priming pump is required.
SEO Product Title
LEO AJM45S Jet Pump 0.45kW 0.6HP 220V Stainless Steel Self-Priming Water Pump
Short Product Description
LEO AJM45S is a 0.45kW / 0.6HP 220V stainless-steel self-priming jet pump designed for clean-water transfer, well-water lifting, garden irrigation and pressure boosting. It delivers approximately 5–40 L/min flow with a 35–16 m head range, featuring a stainless-steel pump body, stainless-steel impeller, AISI 304 shaft, copper motor winding, built-in thermal protection, Class F insulation and IPX4 protection. With 1" × 1" connections and approximately 9 m maximum suction, it is suitable for domestic, irrigation and general clean-water pumping applications.
Inquiry - LEO JET PUMPS - AJM 45S